Electrolux Error Codes & Diagnostics

Heater shorted to ground.

Inspect the heating coil for touching the metal casing. PRO TIP: 'Flow Sense' or restricted airflow errors mean you must clean the vent — this is the #1 fire hazard.

Heater open circuit (most common call).

Inspect and replace the heating element. PRO TIP: 'Flow Sense' or restricted airflow errors mean you must clean the vent — this is the #1 fire hazard.

Appliance is completely unresponsive or behaves erratically.

Info: Communication error between the main control board and other electronic components.

Flashing 'F' on a cooking zone.

Info: No suitable cookware is detected on the induction zone, or the cookware is not centered.

Oven does not heat or function correctly.

Info: Failure in the main electronic control board (PCB).

Oven has overheated and locked the door.

Info: Oven temperature has exceeded its maximum limit, possibly due to a faulty cooling fan or a stuck relay on the control board.

Incorrect temperature readings or oven not heating.

Info: The temperature sensor (thermistor) is faulty or has an open circuit.

Incorrect temperature readings, possibly overheating.

Info: The temperature sensor (thermistor) has a short circuit.

5 Elite Techs Verified

Oven controls are unresponsive or display is erratic.

Info: Communication error between the main control board and the display or touch control board.

Door cannot be locked or unlocked, especially for pyrolytic cleaning.

Info: A fault has been detected with the motorized door lock mechanism.

Oven shuts down unexpectedly.

Info: Internal wiring problem or a checksum error in the control board's memory.

NTC humidity sensor error in the air exhaust duct.

Info: Faulty NTC humidity sensor or its associated circuit in the air exhaust duct.

Condenser NTC sensor error near the compressor.

Info: Faulty Condenser NTC sensor or its associated circuit located near the compressor.

Steam generator NTC sensor error.

Info: Faulty Steam generator NTC sensor or related component within the steam generator unit.

Alarm sound and/or a flashing temperature light or icon.

Info: The internal temperature has risen above a safe level. This can be due to a door left open, a recent large grocery load, or a cooling system failure.

Dishwasher stops filling or has filling issues.

Info: The filling phase timed out. This can be caused by low water pressure or a partial blockage in the inlet.

Dishwasher does not fill with water.

Info: Water supply tap is turned off, inlet hose is bent, or the filter is blocked.

Dishwasher does not drain the water.

Info: Filters are clogged, drain hose is blocked or kinked, or the connection to the sink drain is blocked.

Cycle stops and dishwasher beeps continuously.

Info: The anti-flood protection system has been activated due to a water leak in the base.

Dishwasher fills and drains repeatedly or shows incorrect water level.

Info: Fault with the pressure sensor or level switch, possibly due to clogged filters.

Wash cycle stops, and there is a humming or buzzing noise.

Info: Problem with the main wash motor (circulation pump), often a seized motor or a faulty capacitor.

Dishes are not being cleaned properly, water is cold.

Info: Water is not reaching the correct temperature. This could be a faulty heating element, temperature sensor, or main control board.

Controls are unresponsive, 'L' is displayed.

Info: The Child Lock feature is activated.

A warning alert is displayed regarding the lint filter (as indicated by 'Alerte relative au nettoyage du filtre à peluches').

Info: The lint filter needs cleaning.

The display shows the message 'Not possible' in the text line. This occurs on user interfaces of the TC1 level (BLUE FIRE INSPIRATION models). No buzzer melody is played, and the Start/Pause button LED does not flash.

Info: An option button was pressed that is incompatible with the selected washing program, OR an option button was pressed or the selector was turned during a program run.

Temperature in freezer is not regulated correctly.

Info: The freezer compartment temperature sensor has an open circuit (it's broken or disconnected).

Oven controls are locked and do not respond.

Info: The child safety lock feature is activated.

For TC2, TC3, TC4 user interfaces: 'Err' text flashes on the hour digits. For TC1 user interface: 'Not possible' message appears on the text line. The acoustic signal does not play a specific melody, and the Start/Pause LED does not flash.

Info: An option button incompatible with the selected wash program was pressed OR an option button was pressed OR the selector was moved during cycle execution.

On TC2, TC3, TC4 user interfaces, the text 'Err' flashes in the area displaying the cycle duration numbers. On the TC1 user interface, the message 'Impossible' appears on the text line. The buzzer does not emit a specific melody, and the Start/Pause LED does not flash as on older platforms. This signal is displayed for approximately 1 second.

Info: 1. An option key incompatible with the selected wash program is pressed. 2. An option key is pressed or the selector is moved during an active cycle.

Selection errors are notified to the customer. On UI levels TC2, TC3, TC4, the text 'Err' flashes on the hour digits. On UI level TC1, the message 'Not possible' appears on the text line. The acoustic signal does not play a specific melody, and the Start/Pause LED does not flash. The notification is displayed for approximately 1 second.

Info: An option button incompatible with the selected program was pressed, OR an option button was pressed, or the selector was moved during the cycle execution.