OEM VERIFIED BENCH

OFFICIAL FAULT CODEErr

AEG // OFFICIAL DIAGNOSTIC BENCH

AEG Err

Tumble DryerDrainage System & Drain Pump

Tumble Dryer

Other Brands Sharing Code Err:ElectroluxERR GEERR

Symptom / Description

FAULT

A blinking 'Err' text is displayed in the program duration (for TC2, TC3, TC4 levels) or a 'Not possible' message appears in the text line (for TC1 level). The buzzer does not play a melody, and the Start/Pause button LED does not flash. These signals are shown for approximately 1 second.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

An option button incompatible with the currently selected program was pressed. An option button was pressed or the selector switch was turned during an active program run.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Ensure that selected options are compatible with the chosen program. Avoid pressing option buttons or turning the selector switch during an active program cycle.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide AEG Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpTumble Dryer

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: AEG ERR

FAQ TREE

What does error code ERR mean on a AEG appliance?

AEG error code ERR indicates: A blinking 'Err' text is displayed in the program duration (for TC2, TC3, TC4 levels) or a 'Not possible' message appears in the text line (for TC1 level). The buzzer does not play a melody, and the Start/Pause button LED does not flash. These signals are shown for approximately 1 second..

What is the root cause of AEG error code ERR?

The primary root cause for AEG code ERR is: An option button incompatible with the currently selected program was pressed. An option button was pressed or the selector switch was turned during an active program run..

How do I fix or resolve AEG error code ERR?

To resolve error code ERR: Ensure that selected options are compatible with the chosen program. Avoid pressing option buttons or turning the selector switch during an active program cycle.

Is it safe to clear AEG error code ERR by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if AEG code ERR persists, the physical component causing An option button incompatible with the currently selected program was pressed. An option button was pressed or the selector switch was turned during an active program run. must be inspected or replaced.

How do I test electrical resistance for AEG code ERR using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Drain Pump Motor Stator Coils across Across pump motor spade terminals (L-N unclipped). Expected nominal reading is 160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC). Tolerance: ±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ..

What safety protocol must be followed before servicing AEG code ERR?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?