Skip to content
CodesErreur.comSWISS PRO ENGINE
Core Diagnostics
DiagnosticsBrandsOEM ManualsSpecialistsAI EngineerPRO
Workshop Tools
Diagnostic ToolsNEW
Hardware interfaces & test probes
Find Rating Plate
Locate exact E-Nr, PNC & serial codes
Parts Locator
Global OEM spare parts suppliers
Community & Career
Academy & Courses
Masterclasses by senior technicians
Certification ExamsPRO
Verify your B2B technical credentials
Elite Forum
Peer-to-peer field troubleshooting
Tech Jobs
B2B recruitment & field opportunities
Leaderboard
Global ranking of verified specialists
Certified Appliance Engineering EcosystemApply for Certification →
Language Selector
Account & Access
Upgrade PRO
Back to Search
OEM VERIFIED BENCH
OFFICIAL FAULT CODEE05
Nardi
Nardi // OFFICIAL DIAGNOSTIC BENCH

Nardi E05

Washing MachineNTC Temperature Sensor & Thermistor
Luxury front-loading washing machine in brushed titanium with illuminated dark glass drum
Washing Machine
Other Brands Sharing Code E05:BoschE05SiemensE05SamsungE05LGE05ElectroluxE05AEGE05BekoE05HaierE05CandyE05NeffE05

Symptom / Description

FAULT

Water is not heating up or cycle gets stuck.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

The NTC temperature sensor is faulty (open or short circuit).

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED
1Test the resistance of the NTC sensor (should be around 20k ohms at room temperature). Check wiring to the sensor. Replace the NTC sensor if faulty.
AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time
AI WORKSHOP PROTOCOL ENGINE
Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH
Need Help? Call a Certified TechnicianWorldwide Nardi Parts Finder
Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLNTC Temperature Sensor & ThermistorWashing Machine
2. Multimeter & Electrical Bench Tests (Ω)
MODE: OHMMETER (Ω)AUTO-RANGE
Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board
CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)
Nominal Resistance (Ω)
4.8kΩ–12kΩ (at 20°C–25°C)NOMINAL
0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)
▲ NOMINAL OPERATING WINDOW
Target Component:NTC Temperature Sensor Probe (Thermistor)
Test Pins & Connections
PROBE (+)
PROBE (-)
Across sensor pins 1-2 (unplugged harness)
Tolerance & Diagnostic CriteriaNegative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit.
1. Pre-Intervention Electrical Safety Protocols
  • !Electrical Safety Protocol: Disconnect 230V electrical mains power before removing appliance side or rear panels.
  • !Ensure tub water or heating chamber has cooled below 30°C before unclipping thermistor probe.
  • !Use CAT III 600V/1000V insulated test probes when tng at PCB edge connectors.
3. Preliminary Mechanical & Visual Checks
  • Inspect sensor immersion sleeve for calcification, limescale scale, or thermal paste degradation.
  • Check wiring harness for pinch points, chafing against chassis metal, and terminal pin oxidation.
  • Verify probe is firmly seated in its rubber grommet or bracket inside the water/air circuit.
Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Nardi E05

FAQ TREE
What does error code E05 mean on a Nardi appliance?

Nardi error code E05 indicates: Water is not heating up or cycle gets stuck..

What is the root cause of Nardi error code E05?

The primary root cause for Nardi code E05 is: The NTC temperature sensor is faulty (open or short circuit)..

How do I fix or resolve Nardi error code E05?

To resolve error code E05: Test the resistance of the NTC sensor (should be around 20k ohms at room temperature). Check wiring to the sensor. Replace the NTC sensor if faulty.

Is it safe to clear Nardi error code E05 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Nardi code E05 persists, the physical component causing The NTC temperature sensor is faulty (open or short circuit). must be inspected or replaced.

How do I test electrical resistance for Nardi code E05 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test NTC Temperature Sensor Probe (Thermistor) across Across sensor pins 1-2 (unplugged harness). Expected nominal reading is 4.8kΩ–12kΩ (at 20°C–25°C). Tolerance: Negative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit..

What safety protocol must be followed before servicing Nardi code E05?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

SEMANTIC KNOWLEDGE GRAPH // NARDI

Related Nardi Washing Machine Error Codes

Diagnostic Link Mesh14 OEM Cross-References

Cross-referenced diagnostic codes for technicians inspecting similar component subsystems.

E07Drive Motor, Inverter & Tachometer Sensor
Motor not turning or spinning erratically.
Inspect Protocol
E09Drive Motor, Inverter & Tachometer Sensor
Motor is not running at all or runs at full speed uncontrollably.
Inspect Protocol
E16Heating Element, Thermostat & Safety Fuse
Machine trips the circuit breaker, or water does not heat.
Inspect Protocol
E01Door Lock Mechanism & Safety Interlock
Door will not lock or machine thinks the door is open.
Inspect Protocol
E02Water Inlet Valve, Aquastop & Flowmeter
Machine is not filling with water or filling very slowly.
Inspect Protocol
E03Drainage System & Drain Pump
Machine fails to drain the water.
Inspect Protocol
E04Water Level Pressure Switch & Air Dome
Machine has overfilled with water or leak detected in base.
Inspect Protocol
E1Water Inlet Valve, Aquastop & Flowmeter
Dishwasher fails to fill with water within the expected time.
Inspect Protocol
E2Drainage System & Drain Pump
Dishwasher is not draining the water.
Inspect Protocol
E3Heating Element, Thermostat & Safety Fuse
Water is not heating up, resulting in poor wash performance.
Inspect Protocol
E4Drainage System & Drain Pump
Dishwasher has stopped mid-cycle and may show signs of leaking.
Inspect Protocol
F1NTC Temperature Sensor & Thermistor
Oven not heating correctly, displays error.
Inspect Protocol
F2NTC Temperature Sensor & Thermistor
Oven overheating or not heating correctly.
Inspect Protocol
F3Heating Element, Thermostat & Safety Fuse
Oven has shut down and displays an error.
Inspect Protocol
CodesErreur.com

Premium appliance diagnostics & repair database.
Powered by AI to help certified technicians worldwide.

Trusted by professionals in CH & FR

Platform

Search DatabasePRO Diagnostic AIPRODiagnostic ToolsBrands

Workshop Tools

Brands (87)OEM ManualsFind Rating PlateParts Locator

For Technicians

SpecialistsTechnician ForumTech JobsPremium

Corporate

Terms of ServicePrivacy PolicyOfficial Swiss Repair Partner: Electroassistance
OPERATIONAL SAFETY SPECIFICATION

SAFETY DISCLAIMER

The technical information, diagnostic guides, error codes, and AI-generated suggestions provided on this website are intended exclusively for certified and qualified professionals. Appliance repair involves severe electrical hazards, high voltages, and mechanical risks that can result in fatal injury or severe property damage. If you are not a trained technician, do not attempt to repair any appliances. CodesErreur assumes no responsibility or liability for any damage, injury, or consequential losses resulting from the use of the information provided on this platform. You use all information entirely at your own risk.

© 2026 CodesErreur. All rights reserved.

Official Swiss Repair Partner: Electroassistance Terms of Service Privacy Policy