OEM VERIFIED BENCH

OFFICIAL FAULT CODEF01

Samet // OFFICIAL DIAGNOSTIC BENCH

Samet F01

OvenNTC Temperature Sensor & Thermistor

Oven

Other Brands Sharing Code F01:WhirlpoolF-01 IndesitF01 BauknechtF01 AristonF01 HisenseF01 FAGORF01 ScholtèsF01 Schaub LorenzF01 ArdoF01 AtlanticF01

Symptom / Description

FAULT

Oven temperature sensor error (Open circuit)

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

The oven's NTC temperature sensor is disconnected or has failed.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Check the connection of the sensor to the control board. Test the sensor's resistance; replace if it shows an open circuit.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Samet Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLNTC Temperature Sensor & ThermistorOven / Microwave

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

4.8kΩ–12kΩ (at 20°C–25°C)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:NTC Temperature Sensor Probe (Thermistor)

Test Pins & Connections

PROBE (+)

PROBE (-)

Across sensor pins 1-2 (unplugged harness)

Tolerance & Diagnostic CriteriaNegative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Disconnect 230V electrical mains power before removing appliance side or rear panels.
!Ensure tub water or heating chamber has cooled below 30°C before unclipping thermistor probe.
!Use CAT III 600V/1000V insulated test probes when tng at PCB edge connectors.

3. Preliminary Mechanical & Visual Checks

Inspect sensor immersion sleeve for calcification, limescale scale, or thermal paste degradation.
Check wiring harness for pinch points, chafing against chassis metal, and terminal pin oxidation.
Verify probe is firmly seated in its rubber grommet or bracket inside the water/air circuit.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Samet F01

FAQ TREE

What does error code F01 mean on a Samet appliance?

Samet error code F01 indicates: Oven temperature sensor error (Open circuit).

What is the root cause of Samet error code F01?

The primary root cause for Samet code F01 is: The oven's NTC temperature sensor is disconnected or has failed..

How do I fix or resolve Samet error code F01?

To resolve error code F01: Check the connection of the sensor to the control board. Test the sensor's resistance; replace if it shows an open circuit.

Is it safe to clear Samet error code F01 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Samet code F01 persists, the physical component causing The oven's NTC temperature sensor is disconnected or has failed. must be inspected or replaced.

How do I test electrical resistance for Samet code F01 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test NTC Temperature Sensor Probe (Thermistor) across Across sensor pins 1-2 (unplugged harness). Expected nominal reading is 4.8kΩ–12kΩ (at 20°C–25°C). Tolerance: Negative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit..

What safety protocol must be followed before servicing Samet code F01?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEF01

Samet // OFFICIAL DIAGNOSTIC BENCH

Samet F01

OvenNTC Temperature Sensor & Thermistor

Oven

Other Brands Sharing Code F01:WhirlpoolF-01 IndesitF01 BauknechtF01 AristonF01 HisenseF01 FAGORF01 ScholtèsF01 Schaub LorenzF01 ArdoF01 AtlanticF01

Symptom / Description

FAULT

Oven temperature sensor error (Open circuit)

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

The oven's NTC temperature sensor is disconnected or has failed.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Check the connection of the sensor to the control board. Test the sensor's resistance; replace if it shows an open circuit.

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Samet Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLNTC Temperature Sensor & ThermistorOven / Microwave

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

4.8kΩ–12kΩ (at 20°C–25°C)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:NTC Temperature Sensor Probe (Thermistor)

Test Pins & Connections

PROBE (+)

PROBE (-)

Across sensor pins 1-2 (unplugged harness)

Tolerance & Diagnostic CriteriaNegative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Disconnect 230V electrical mains power before removing appliance side or rear panels.
!Ensure tub water or heating chamber has cooled below 30°C before unclipping thermistor probe.
!Use CAT III 600V/1000V insulated test probes when tng at PCB edge connectors.

3. Preliminary Mechanical & Visual Checks

Inspect sensor immersion sleeve for calcification, limescale scale, or thermal paste degradation.
Check wiring harness for pinch points, chafing against chassis metal, and terminal pin oxidation.
Verify probe is firmly seated in its rubber grommet or bracket inside the water/air circuit.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Samet F01

FAQ TREE

What does error code F01 mean on a Samet appliance?

Samet error code F01 indicates: Oven temperature sensor error (Open circuit).

What is the root cause of Samet error code F01?

The primary root cause for Samet code F01 is: The oven's NTC temperature sensor is disconnected or has failed..

How do I fix or resolve Samet error code F01?

To resolve error code F01: Check the connection of the sensor to the control board. Test the sensor's resistance; replace if it shows an open circuit.

Is it safe to clear Samet error code F01 by resetting power?

How do I test electrical resistance for Samet code F01 using a multimeter?

What safety protocol must be followed before servicing Samet code F01?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Samet F01

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Samet F01

Community Verification

Related Samet Oven / Microwave Error Codes

Samet F01

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Samet F01

Community Verification

Related Samet Oven / Microwave Error Codes