Hoover Error Codes & Diagnostics
Complete B2B dictionary of fault codes, troubleshooting steps, and repair manuals for Hoover home appliances, including Washing Machines, Dishwashers, Ovens, Dryers, and Refrigerators.
37 Verified Codes in Database
Are you a Certified Technician?Stamp unverified codes below to earn +10 Reputation Points.
(Only available for users logged in with a Google account)
(Only available for users logged in with a Google account)
| Code | Fault / Diagnostics | Appliances | Action |
|---|---|---|---|
| AL03 | Water Heating Timeout Info: The dishwasher failed to reach the target temperature within the expected time frame. | Dishwasher | |
| E01 | Door Lock Fault Info: The door is not closed properly, the lock mechanism is faulty, or there's a wiring issue to the lock. | Washing Machine | |
| E1 | Refrigerator Sensor Fault Info: The temperature sensor in the refrigerator compartment is faulty (open or short circuit). | Refrigerator | |
| E02 | Water Fill Timeout Info: Water supply is turned off, inlet hose is kinked, or the water inlet valve is blocked or faulty. | Washing Machine | |
| E2 | Electronics Overheating Info: The internal electronic components of the hob have exceeded their safe operating temperature. | Hob | |
| E03 | Water Drain Timeout Info: The drain filter is blocked, the drain hose is kinked or blocked, or the drain pump is faulty. | Washing Machine | |
| E3 | Defrost Sensor Fault Info: The defrost sensor located on the evaporator coil is faulty. | Refrigerator | |
| E04 | Anti-Flood Activated / Overfill Info: Too much detergent causing over-foaming, or a faulty pressure switch or water inlet valve. | Washing Machine | |
| E4 | Cooking Zone Overheating Info: A cooking zone has overheated, possibly due to an empty pan being left on high heat. | Hob | |
| E05 | NTC Temperature Sensor Fault Info: The water temperature sensor (NTC) has an open or short circuit, or a wiring fault. | Washing Machine | |
| E06 | Unbalanced Load or Control Board Fault Info: The laundry load is severely unbalanced, or the main electronic control board (PCB) is faulty. | Washing Machine | |
| E6 | Power Board Communication Fault Info: There is a communication error between the control interface and one of the power boards. | Hob | |
| E07 | Motor Jammed or Door Lock Rapid Operation Info: Motor is jammed, preventing rotation, or a fault in the door lock mechanism is causing rapid cycling. | Washing Machine | |
| E7 | Flow Meter Fault Info: The flow meter (turbine) that measures water intake is not spinning or sending a signal. | Dishwasher | |
| E08 | Motor Speed Sensor Fault Info: The motor tacho sensor, which measures drum speed, is faulty or has a bad connection. | Washing Machine | |
| E8 | Ventilation Fault Info: Air circulation to the main control board is insufficient, often due to an installation issue. | Hob | |
| E09 | Motor Triac Fault Info: The motor's power control component (triac) on the main PCB has short-circuited. | Washing Machine | |
| E9 | Internal Electronics Fault Info: A general hardware or software fault has occurred on the main control board. | Hob | |
| E10 | Drum Sensor or Timer Fault Info: On older models, this indicates a timer fault. On newer models, it can relate to a drum position sensor. | Washing Machine | |
| E11 | Dryer Sensor Open Circuit Info: The sensor for the drying cycle is faulty or its wiring is disconnected. | Washer Dryer | |
| E12 | PCB Communication Error Info: Communication is lost between the main control board and the display board. | Washer Dryer | |
| E13 | Main Control Board (PCB) Fault Info: A general fault has been detected on the main electronic module. | Washing Machine | |
| E14 | Water Heating Fault Info: The machine is unable to heat the water. The heating element or NTC sensor is faulty. | Washer Dryer | |
| E15 | Control Board Programming Error Info: The memory chip on the control board is corrupt or the board has not been programmed correctly. | Washing Machine | |
| E16 | Heater Insulation Fault / Short Circuit Info: The heating element's insulation has failed, causing a short circuit that can trip the home's circuit breaker. | Washing Machine | |
| E17 | Motor Tacho Signal Issue Info: The motor speed sensor (tacho) is providing an incorrect or unstable signal to the control board. | Washing Machine | |
| E18 | Control Board Input Signal Fault Info: The main control board has detected an incorrect input frequency from the mains supply. | Washing Machine | |
| E20 | Drain Fault (alternative code) Info: This is often the same as E03; indicates a problem with the draining system, such as a blocked filter or pump. | Washing Machine | |
| F | Pan Not Detected Info: No pan is on the cooking zone, or the pan is not suitable for induction cooking (e.g., not magnetic). | Hob | |
| F1 | NTC Sensor Open Circuit Info: The oven's temperature sensor (NTC) or its wiring is open circuit. | Oven |