Access our premium database of error codes, common faults, and professional repair solutions for Sangiorgio appliances.
Freezer high temperature alarm
The freezer temperature has risen above a safe level, possibly after a power cut or due to a system fault.
Check that the door is sealed correctly. Press the alarm reset button. If the alarm returns, there is a fault in the cooling system.
Refrigerator high temperature alarm
The fridge compartment temperature is too high. Usually caused by the door being left open.
Check for items obstructing the door from closing fully. Ensure the door seal is clean and making good contact.
Sangiorgio AL01: Water inlet / filling timeout in Dishwasher; appliance fails to fill to minimum operational level.
Synonymous with E4. The anti-flood system in the base has been activated by a leak.
Unplug the appliance, absorb water from the base tray, locate the source of the leak (hoses, seals) and repair it.
Sangiorgio AL03: Water drainage failure detected in Dishwasher; drain pump cannot evacuate water within safety time limit.
The dishwasher is unable to drain water within the allotted time. Clogged filters or blocked drain hose.
Thoroughly clean all filters in the sump area. Check the drain hose for kinks and ensure it is not blocked.
Circulation pump / Wash motor fault
The main wash motor is blocked, its capacitor has failed, or the motor itself is faulty.
Check the wash motor for any obstructions like glass or plastic. Test the motor's start capacitor. If these are fine, the motor may need replacement.
Sangiorgio E01: Door lock safety interlock fault in Washing Machine; door switch contact fails to close or open.
The door is not closed properly, the door lock mechanism is faulty, or there is a wiring issue to the lock.
Ensure the door is firmly closed. Check wiring to the door lock. If the issue persists, replace the door interlock.
Water fill timeout or leak detected
Water supply is off, inlet hose blocked, or the anti-flood system in the base has been activated by a leak.
Check water supply and inlet hose. If water is present in the base of the dishwasher, find and repair the leak before resetting.
Water fill problem / Timeout
Water supply is turned off, inlet hose is kinked or its filter is blocked, or the water inlet valve is faulty.
Check that the water tap is open. Straighten the inlet hose and clean the filter at the tap end. Test and replace the inlet solenoid valve if necessary.
Sangiorgio E2: Water drainage failure detected in Dishwasher; drain pump cannot evacuate water within safety time limit.
Filters are blocked, the drain hose is obstructed or kinked, or the drain pump is faulty.
Clean the main filter and microfilter. Check the drain hose for any kinks. Inspect the drain pump for blockages.
Sangiorgio E03: Water drainage failure detected in Washing Machine; drain pump cannot evacuate water within safety time limit.
The drain filter is clogged, the drain pump is blocked or faulty, or the drain hose is kinked or blocked.
Clean the drain pump filter. Check the pump impeller for obstructions. Ensure the drain hose is not kinked and is clear.
Sangiorgio E3: NTC temperature sensor signal out of range (open or short circuit) in Dishwasher.
The heating element or the temperature sensor (NTC) has failed, or there is a wiring issue.
Test the heating element for continuity and check its connections. Test the NTC sensor. The main board could also be at fault.
Overfill or anti-flood switch activated
Too much water in the drum, likely due to a faulty pressure switch or a stuck water inlet valve.
Check the pressure switch and its connecting hose for blockages. Inspect the water inlet valve to ensure it's not letting water in when powered off.
Leak detected / Anti-flood activated
Water has leaked into the base of the machine, tripping the anti-flood float switch.
Disconnect power. Tilt the dishwasher to drain the base. Find the source of the leak (hoses, seals, pump) and repair it.
Temperature sensor (NTC) fault
The NTC temperature sensor is faulty, or there's a problem with its wiring or connection to the control board.
Check the wiring and connections to the NTC sensor. Test the sensor's resistance with a multimeter; replace if out of range.
Temperature sensor (NTC) fault
The NTC sensor is giving an incorrect reading, is open circuit, or short circuit.
Check the wiring to the NTC sensor. Test the sensor with a multimeter and replace if the resistance value is incorrect.
Machine unbalanced or control board fault
The laundry load is severely unbalanced, or the machine's control board has a calibration or component fault.
Stop the machine and redistribute the laundry. If the error persists with a balanced load, the main control board may need replacement.
Sangiorgio E6: Water inlet / filling timeout in Dishwasher; appliance fails to fill to minimum operational level.
The water inlet valve (solenoid) has an open circuit or is faulty.
Test the coil on the inlet valve for continuity. If it's an open circuit, the valve assembly needs to be replaced.
Motor fault / Drum not turning
The motor is jammed, motor brushes are worn, or the motor's tacho sensor is faulty.
Check if the drum turns by hand. Inspect motor brushes for wear and replace if shorter than 15mm. Check motor and tacho wiring.
Flow meter or diverter valve fault
The flow meter that measures water intake is not working, or the diverter valve that directs water to the spray arms is stuck.
Check the flow meter for blockages or faulty wiring. Check the diverter valve motor and mechanism for free movement.
Motor speed sensor (tacho) fault
The motor's tachometer coil has an open circuit, the magnet is dislodged, or wiring is faulty.
Inspect the tacho coil and its magnet on the motor's shaft. Check for continuity on the coil and verify wiring to the control board.
Motor triac fault on control board
A short circuit in the motor's power controller (triac) on the main PCB. Motor may run at full speed immediately.
This fault requires professional diagnosis. The main control board (PCB) usually needs to be replaced.
Dryer sensor open circuit
The temperature sensor for the drying circuit is faulty or its wiring is disconnected.
Applicable to washer-dryers only. Check the wiring to the dryer NTC sensor and replace the sensor if it tests as open circuit.
Communication error between control boards
The connection between the main control board and the display board is lost or corrupted.
Check the wiring harness and connectors between the two electronic boards. Reseat the connectors. The fault could be with either board.
Sangiorgio E14: NTC temperature sensor signal out of range (open or short circuit) in Washing Machine.
The heating element has failed, or there is an issue with the wiring or the NTC temperature sensor.
Test the heating element for continuity. Check the NTC sensor and all related wiring for damage or loose connections.
Control board programming error
The memory chip (EEPROM) on the control board is not programmed or has become corrupted.
The main control board needs to be reprogrammed by a qualified technician or replaced.
Heater insulation fault / Short circuit
The heating element's insulation has failed, causing a short circuit which may trip the mains power.
Disconnect the machine and test the heating element for a short to earth using a multimeter. Replace the heating element.
Touch control communication fault
The touch control panel is not communicating correctly with the main board.
Perform a hard reset by turning off the appliance at the breaker for 5 minutes. If the error returns, the touch control panel may need replacement.
Freezer compartment sensor fault
The NTC temperature sensor in the freezer section is faulty (open or short circuit).
The freezer NTC sensor needs to be tested and likely replaced. This often requires partial disassembly of the freezer interior.
Refrigerator compartment sensor fault
The NTC temperature sensor in the fridge section is faulty (open or short circuit).
The fridge NTC sensor needs to be tested with a multimeter and replaced if faulty.
Sangiorgio F3: Cooling circuit or defrost system anomaly in Refrigerator / Freezer; compartment temperature deviation.
The defrost termination sensor located on the evaporator coil has failed.
This sensor prevents the evaporator from overheating during a defrost cycle. It requires access to the evaporator coil for replacement.
Our official certified partners service Sangiorgio appliances in your area.