Access our premium database of error codes, common faults, and professional repair solutions for Whirlpool appliances.
Whirlpool F-22: NTC temperature sensor signal out of range (open or short circuit) in Tumble Dryer.
On Whirlpool Dryer: Defective NTC Temperature Sensor Probe (Thermistor), open/short circuit in the wiring harness, or faulty connector on the ntc temperature sensor & thermistor.
On Whirlpool Dryer: Test exhaust thermistor resistance. PRO TIP: 'Flow Sense' or restricted airflow errors mean you must clean the vent — this is the #1 fire hazard.
Whirlpool 6th Sense Supreme Care Heat Pump Tumble Dryer: Heat pump compressor discharge overtemperature warning F22; high-pressure line thermistor exceeds 115°C safety ceiling.
On Whirlpool heat pump dryers: Severely blocked bottom condenser filter choking airflow, slow evaporator blower fan, or micro-leak in R134a/R290 gas circuit.
Clean or replace lower foam condenser filter block. Vacuum aluminum heat exchanger fins. Verify secondary cooling fan operates freely during drying. Rotate cycle dial to 6 o'clock, press Start 3 times, rotate to 7 o'clock, press Start 3 times, then return to Off.
Whirlpool 6th Sense Supreme Care & FreshCare+ Washing Machine: Motor drive inverter module overcurrent fault F22; IPM power silicon senses short circuit or excessive motor stator phase current.
On Whirlpool washing appliances: Shorted winding in 3-phase BLDC motor stator, locked drum mechanical assembly, or punctured IGBT bridge on power board.
Measure resistance between motor phase pins U-V, V-W, U-W (must be symmetrical, 6.5–8.5 Ω per phase). Test for zero resistance across IGBT output terminals. Turn cycle selector to 6 o'clock (Drain/Spin), press Cancel/Reset button 4 times within 5 seconds, then cycle power.
Whirlpool F-23: NTC temperature sensor signal out of range (open or short circuit) in Tumble Dryer.
On Whirlpool Dryer: Defective NTC Temperature Sensor Probe (Thermistor), open/short circuit in the wiring harness, or faulty connector on the ntc temperature sensor & thermistor.
On Whirlpool Dryer: Test exhaust thermistor resistance. PRO TIP: 'Flow Sense' or restricted airflow errors mean you must clean the vent — this is the #1 fire hazard.
Whirlpool 6th Sense Supreme Care Heat Pump Tumble Dryer: Lower condenser filter blockage warning F23; differential pressure switch or temperature delta detects restricted air path.
On Whirlpool tumble dryers: Compressed sponge filter saturated with damp lint in bottom plinth compartment, or warped filter frame allowing air bypass.
Open plinth door, pull out foam filter element, wash thoroughly under running water, squeeze dry with towel, and reinstall firmly into cassette housing. Rotate cycle dial to 6 o'clock, press Start 3 times, rotate to 7 o'clock, press Start 3 times, then return to Off.
Whirlpool 6th Sense Supreme Care & FreshCare+ Washing Machine: Simultaneous empty and full pressure switch signals F23; logic inconsistency detected between dual pressure contacts.
On Whirlpool washers: Moisture inside mechanical pressure switch capsule, oxidation on pressure contacts, or soap scum blocking pressure tube orifice.
Inspect and clear pressure switch nipple and chamber. Check continuity across contact pins 11-12 (empty, 0 Ω) and 11-14 (full, open when tub is drained). Turn cycle selector to 6 o'clock (Drain/Spin), press Cancel/Reset button 4 times within 5 seconds, then cycle power.
Whirlpool 6th Sense Supreme Care Heat Pump Tumble Dryer: Electronic humidity sensing amplifier calibration drift F24; analog-to-digital converter reports uncalibrated reference voltage.
On Whirlpool tumble dryers: High ambient humidity during calibration check, dried-out electrolytic filtering capacitor on PCB, or defective operational amplifier IC.
Ventilate laundry room to lower ambient humidity below 70%. Ensure drum is completely empty and dry. Execute factory diagnostic self-calibration routine. Rotate cycle dial to 6 o'clock, press Start 3 times, rotate to 7 o'clock, press Start 3 times, then return to Off.
Whirlpool 6th Sense Supreme Care & FreshCare+ Washing Machine: Overflow water level threshold tripped F24; critical safety level exceeded, engaging emergency drain routine.
On Whirlpool washers: Mechanically jammed inlet water valve allowing unmetered filling, or defective triac supplying continuous 230V to inlet solenoid.
Shut off water isolation valve. Check if water continues flowing with mains unplugged (valve jammed open). If stops, test triac output on main board. Turn cycle selector to 6 o'clock (Drain/Spin), press Cancel/Reset button 4 times within 5 seconds, then cycle power.
Whirlpool 6th Sense FlexiCook & CleanProtect Induction Cooktop: Rear induction zone center temperature sensor disconnect F25; glass ceramic sensor spring probe circuit open.
On Whirlpool cooktops: Broken copper wire at coil center spring eyelet, oxidized plug on generator board, or cracked ceramic thermistor chip.
Unclip glass top and access rear induction coil. Measure center spring NTC probe resistance (nominal ~100 kΩ at 25°C). Replace central coil sensor. Disconnect mains supply at isolation switch for 2 minutes, clean cooktop glass surface, and restore power.
Whirlpool 6th Sense Supreme Care & FreshCare+ Washing Machine: Main drain pump triac driver fault F26; power board detects shorted or open triac output stage to pump motor.
On Whirlpool washing machines: Water ingress into drain pump motor body causing winding short circuit that punctures the board triac driver.
Inspect drain pump for signs of water leaking down shaft into coil. Measure pump resistance (160–185 Ω). Replace pump and repair or replace power module. Turn cycle selector to 6 o'clock (Drain/Spin), press Cancel/Reset button 4 times within 5 seconds, then cycle power.
Whirlpool 6th Sense Supreme Care & FreshCare+ Washing Machine: Drum reversing motor relay contact stuck F27; motor can rotate in only one direction due to welded relay contacts.
On Whirlpool washing appliances: High inductive arc discharge during drum reversal under heavy laundry load welding reversing relay contacts on PCB.
De-energize machine. Tap relay casing lightly or measure contact continuity with power off (normally open contacts must read infinite ohms). Replace PCB relay. Turn cycle selector to 6 o'clock (Drain/Spin), press Cancel/Reset button 4 times within 5 seconds, then cycle power.
Whirlpool 6th Sense Supreme Care & FreshCare+ Washing Machine: Motor stator tap field weakening failure F28; high-speed spin field switching relay does not engage.
On Whirlpool washers: Open circuit in stator intermediate winding tap, broken motor wiring harness terminal, or defective field-weakening relay.
Measure resistance across stator tap winding connections on motor terminal block (nominal 1.2–2.5 Ω). Check 12V DC coil activation on field relay. Turn cycle selector to 6 o'clock (Drain/Spin), press Cancel/Reset button 4 times within 5 seconds, then cycle power.
Whirlpool 6th Sense Supreme Care & FreshCare+ Washing Machine: Door lock interlock failure F29; latch microswitch contact fails to close within 15 seconds of cycle start command.
On Whirlpool washing appliances: Broken door latch hook, sagging door hinges, burnt PTC wax tablet, or open solenoid coil in motorized door lock.
Inspect door latch alignment with front strike plate. Measure door lock solenoid resistance (nominal 800–1100 Ω) or PTC tablet (700–1200 Ω). Replace lock mechanism. Turn cycle selector to 6 o'clock (Drain/Spin), press Cancel/Reset button 4 times within 5 seconds, then cycle power.
On Whirlpool Oven: Oven not heating or inaccurate temperature
On Whirlpool Oven: Open circuit detected in the oven temperature sensor (thermistor).
On Whirlpool Oven: Test the sensor with a multimeter for resistance (should be ~1100 Ohms at room temp). If open, replace the sensor.
On Whirlpool Oven: Oven overheating or inaccurate temperature
On Whirlpool Oven: Shorted oven temperature sensor (thermistor).
On Whirlpool Oven: Test the sensor with a multimeter. If it shows a short (near zero Ohms), it needs to be replaced.
On Whirlpool Oven: Oven gets too hot during preheat or cooking
On Whirlpool Oven: Oven is overheating. This can be caused by a faulty temperature sensor or a stuck relay on the control board.
On Whirlpool Oven: Check the temperature sensor first. If it tests okay, the main control board is likely the cause.
Whirlpool 6th Sense FlexiCook & CleanProtect Induction Cooktop: Front left induction coil NTC sensor calibration drift F36; analog voltage reading indicates out-of-range temperature curve.
On Whirlpool cooktops: Thermal degradation of sensor bead due to repeated overheating, dry silicone thermal coupling, or moisture on sensor connector.
Measure front left coil NTC resistance: ~100 kΩ at 25°C (falling to ~10 kΩ at 80°C). Clean sensor contact face and renew thermal paste. Replace NTC if drifted. Disconnect mains supply at isolation switch for 2 minutes, clean cooktop glass surface, and restore power.
Whirlpool 6th Sense FlexiCook & CleanProtect Induction Cooktop: Power board mains input voltage out of tolerance F37; line monitoring circuit detects voltage below 160V or exceeding 285V RMS.
On Whirlpool cooktops: Electrical grid brownout, defective neutral bonding in home panel, or degraded voltage sensing resistor divider on filter board.
Test mains supply voltage at cooktop terminal block under load. If household supply is normal (230V ± 10%), inspect voltage sensing circuit on filter PCB. Disconnect mains supply at isolation switch for 2 minutes, clean cooktop glass surface, and restore power.
On Whirlpool Oven: Meat probe function is not working.
On Whirlpool Oven: The meat probe sensor is shorted.
On Whirlpool Oven: Unplug the meat probe. If the error disappears, replace the meat probe. If it remains, check the probe receptacle and wiring.
Whirlpool 6th Sense FlexiCook & CleanProtect Induction Cooktop: Left induction generator module bus communication failure F40; power inverter microcontroller fails to respond to poll command.
On Whirlpool cooktops: Open circuit on internal serial data link, blown auxiliary low-voltage fuse on left generator, or failed power supply regulator.
Check internal bus wiring connecting left generator board. Verify onboard SMD fuses (T3.15A / T2A) and test 5V DC and 12V DC power supply rails. Disconnect mains supply at isolation switch for 2 minutes, clean cooktop glass surface, and restore power.
Whirlpool 6th Sense FlexiCook & CleanProtect Induction Cooktop: Incorrect mains line supply connection F42; 400V phase-to-phase accidentally wired to 230V phase-to-neutral terminal.
On Whirlpool cooktops: Missing neutral copper link bridge on terminal board, or neutral connected to second 400V live line in domestic wall junction.
Shut off power immediately. Inspect terminal box wiring diagram. Install copper bridge between N1 and N2 terminals. Verify true Neutral (0V to Earth). Disconnect mains supply at isolation switch for 2 minutes, clean cooktop glass surface, and restore power.
Whirlpool 6th Sense FlexiCook & CleanProtect Induction Cooktop: LIN bus communication lost between touch UI and power filter PCB F47; master controller drops link to auxiliary filter board.
On Whirlpool cooktops: Loose multi-pin LIN bus connector, moisture condensation on filter board transceiver, or blown power supply resistor.
Inspect LIN bus harness connecting touch UI and filter PCB. Reseat connectors firmly. Verify 12V DC input to filter transceiver IC. Replace harness if damaged. Disconnect mains supply at isolation switch for 2 minutes, clean cooktop glass surface, and restore power.
On Whirlpool Oven: Self-clean cycle won't start, door won't lock
On Whirlpool Oven: The door lock mechanism has failed to lock.
On Whirlpool Oven: Check for obstructions in the door path. Inspect the motorized door lock assembly for damage or failure.
Whirlpool F5 E2: Water inlet / filling timeout in Refrigerator / Freezer; appliance fails to fill to minimum operational level.
On Whirlpool Refrigerator: Defective PTC Heater Pellet / Pulse Solenoid / Microswitch Contacts, open/short circuit in the wiring harness, or faulty connector on the door lock mechanism & safety interlock.
On Whirlpool Refrigerator: Check door switch and hinges for alignment. PRO TIP: If your fridge is showing any 'E' code and it's under 5 years old, always try a hard reset (unplug 10 minutes) before calling. 60% of the time it clears temporary glitches.
On Whirlpool Dryer: User interface board failure.
On Whirlpool Dryer: Defective PCB Power Supply Rails & DC Bus Filter Capacitors, open/short circuit in the wiring harness, or faulty connector on the electronic control board (pcb) & bus communications.
On Whirlpool Dryer: Check connection between user interface and main board. PRO TIP: 'Flow Sense' or restricted airflow errors mean you must clean the vent — this is the #1 fire hazard.
On Whirlpool Dryer: User interface board failure.
On Whirlpool Dryer: Defective PCB Power Supply Rails & DC Bus Filter Capacitors, open/short circuit in the wiring harness, or faulty connector on the electronic control board (pcb) & bus communications.
On Whirlpool Dryer: Check connection between user interface and main board. PRO TIP: 'Flow Sense' or restricted airflow errors mean you must clean the vent — this is the #1 fire hazard.
On Whirlpool Oven: Oven not working, error displayed
On Whirlpool Oven: Mismatch in wiring or component checksum error on the control board.
On Whirlpool Oven: Check for any miswired components after a repair. Often requires replacing the main control board.
Whirlpool 6th Sense PowerClean Pro & MaxiSpace Dishwasher: Optical Water Indicator (OWI) turbidity sensor failure FA; infra-red optoelectronic receiver signal distorted or disconnected.
On Whirlpool dishwashers: Soil deposition on OWI prism lenses, defective phototransistor diode, or wiring harness disconnect on base sump interface.
Clean optical prism face of OWI sensor inside sump. Verify 5V DC supply and signal line to main board. Replace OWI sensor assembly if cleaning fails. Hold Cancel/Drain button for 5 seconds until drain cycle begins, allow 60s for sump evacuation, then power off and on.
Whirlpool 6th Sense PowerClean Pro & MaxiSpace Dishwasher: Motorized Diverter Valve (MDV) microswitch failure FB; cam switch does not pulse during diverter disc positioning.
On Whirlpool dishwashers: Broken nylon gear teeth in MDV actuator, burnt drive motor winding, or oxidized internal microswitch wiper contacts.
Measure MDV synchronous drive motor resistance (6.0–7.5 kΩ). Check microswitch continuity with manual gear rotation (must switch between 0 Ω and infinite). Replace MDV. Hold Cancel/Drain button for 5 seconds until drain cycle begins, allow 60s for sump evacuation, then power off and on.
Whirlpool 6th Sense PowerClean Pro & MaxiSpace Dishwasher: Water softener hardness sensor circuit fault FC; salt concentration conductivity measurement signal interrupted.
On Whirlpool dishwashers: Salt bridge in brine tank preventing sensor contact, corroded conductivity electrode pins, or disconnected softener wiring harness.
Stir salt container with wooden spoon to break crusts. Add 500ml warm water. Clean electrode pins and check wiring continuity to main control PCB. Hold Cancel/Drain button for 5 seconds until drain cycle begins, allow 60s for sump evacuation, then power off and on.
Our official certified partners service Whirlpool appliances in your area.