OEM VERIFIED BENCH

OFFICIAL FAULT CODEF10

Whirlpool // OFFICIAL DIAGNOSTIC BENCH

Whirlpool F10

DishwasherDrainage System & Drain Pump

Dishwasher

Select Appliance Type

0ms Instant Telemetry Switch

Other Brands Sharing Code F10:MieleF10 IndesitF10 BauknechtF10 AristonF10 BrandtF10 De DietrichF10 LiebherrF10 SchulthessF10 SauterF10 ScholtèsF10

Symptom / Description

FAULT

Whirlpool 6th Sense PowerClean Pro & MaxiSpace Dishwasher: Heating circuit safety relay stuck open F10; DEA700 power module fails to close high-current heater contact.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Whirlpool dishwashers: Open relay driver transistor on DEA700 PCB, defective relay coil, or broken trace in high-current heating loop.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Inspect DEA700 power module for burned solder pads under heater relay. Measure relay coil continuity (nominal 350–450 Ω). Replace power board if relay damaged. Hold Cancel/Drain button for 5 seconds until drain cycle begins, allow 60s for sump evacuation, then power off and on.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Whirlpool Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Whirlpool F10

FAQ TREE

What does error code F10 mean on a Whirlpool appliance?

Whirlpool error code F10 indicates: Whirlpool 6th Sense PowerClean Pro & MaxiSpace Dishwasher: Heating circuit safety relay stuck open F10; DEA700 power module fails to close high-current heater contact..

What is the root cause of Whirlpool error code F10?

The primary root cause for Whirlpool code F10 is: On Whirlpool dishwashers: Open relay driver transistor on DEA700 PCB, defective relay coil, or broken trace in high-current heating loop..

How do I fix or resolve Whirlpool error code F10?

To resolve error code F10: Inspect DEA700 power module for burned solder pads under heater relay. Measure relay coil continuity (nominal 350–450 Ω). Replace power board if relay damaged. Hold Cancel/Drain button for 5 seconds until drain cycle begins, allow 60s for sump evacuation, then power off and on.

Is it safe to clear Whirlpool error code F10 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Whirlpool code F10 persists, the physical component causing On Whirlpool dishwashers: Open relay driver transistor on DEA700 PCB, defective relay coil, or broken trace in high-current heating loop. must be inspected or replaced.

How do I test electrical resistance for Whirlpool code F10 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Drain Pump Motor Stator Coils across Across pump motor spade terminals (L-N unclipped). Expected nominal reading is 160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC). Tolerance: ±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ..

What safety protocol must be followed before servicing Whirlpool code F10?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEF10

Whirlpool // OFFICIAL DIAGNOSTIC BENCH

Whirlpool F10

DishwasherDrainage System & Drain Pump

Dishwasher

Select Appliance Type

0ms Instant Telemetry Switch

Other Brands Sharing Code F10:MieleF10 IndesitF10 BauknechtF10 AristonF10 BrandtF10 De DietrichF10 LiebherrF10 SchulthessF10 SauterF10 ScholtèsF10

Symptom / Description

FAULT

Whirlpool 6th Sense PowerClean Pro & MaxiSpace Dishwasher: Heating circuit safety relay stuck open F10; DEA700 power module fails to close high-current heater contact.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Whirlpool dishwashers: Open relay driver transistor on DEA700 PCB, defective relay coil, or broken trace in high-current heating loop.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Whirlpool Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Whirlpool F10

FAQ TREE

What does error code F10 mean on a Whirlpool appliance?

What is the root cause of Whirlpool error code F10?

The primary root cause for Whirlpool code F10 is: On Whirlpool dishwashers: Open relay driver transistor on DEA700 PCB, defective relay coil, or broken trace in high-current heating loop..

How do I fix or resolve Whirlpool error code F10?

Is it safe to clear Whirlpool error code F10 by resetting power?

How do I test electrical resistance for Whirlpool code F10 using a multimeter?

What safety protocol must be followed before servicing Whirlpool code F10?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Whirlpool F10

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Whirlpool F10

Community Verification

Related Whirlpool Dishwasher Error Codes

Whirlpool F10

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Whirlpool F10

Community Verification

Related Whirlpool Dishwasher Error Codes