OEM VERIFIED BENCH

OFFICIAL FAULT CODEi58

Arthur Martin // OFFICIAL DIAGNOSTIC BENCH

Arthur Martin i58

Q: What does error code I58 mean on a Arthur Martin appliance?

Arthur Martin error code I58 indicates: Arthur Martin ASF Series / Calypso / Electrolux Luxe Dishwasher: Circulation pump motor phase disconnected or stator open circuit i58; inverter senses missing phase current..

Q: What is the root cause of Arthur Martin error code I58?

The primary root cause for Arthur Martin code I58 is: On Arthur Martin (Arthur Martin ASF Series / Calypso / Electrolux Luxe Dishwasher) models: Cut wire in three-phase motor cable harness, terminal pin backed out of plastic housing, or open stator winding inside motor..

Q: How do I fix or resolve Arthur Martin error code I58?

To resolve error code I58: Test electrical continuity of each phase lead from inverter board to motor terminals (< 0.5 Ω). Replace motor if winding is open (infinite Ω). Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

Q: Is it safe to clear Arthur Martin error code I58 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Arthur Martin code I58 persists, the physical component causing On Arthur Martin (Arthur Martin ASF Series / Calypso / Electrolux Luxe Dishwasher) models: Cut wire in three-phase motor cable harness, terminal pin backed out of plastic housing, or open stator winding inside motor. must be inspected or replaced.

Q: How do I test electrical resistance for Arthur Martin code I58 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test 3-Phase Motor Windings / Tacho Generator / Carbon Brushes across Across phase pins U-V, V-W, U-W on motor harness; across tacho pins. Expected nominal reading is 3Ω–6Ω (BLDC phase U-V-W) / 60Ω–180Ω (Tacho coil) / 1.5Ω–3.5Ω (Universal stator). Tolerance: BLDC phase winding values must be strictly balanced within ±0.3Ω. Hand rotation generates 1V–4V AC on tacho..

Q: What safety protocol must be followed before servicing Arthur Martin code I58?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

DishwasherDrive Motor, Inverter & Tachometer Sensor

Dishwasher

Other Brands Sharing Code i58:ElectroluxI58 AEGI58 ZanussiI58 CastorI58 FaureI58 FrigidaireI58 KelvinatorI58 WestinghouseI58 ZoppasI58

Symptom / Description

FAULT

Arthur Martin ASF Series / Calypso / Electrolux Luxe Dishwasher: Circulation pump motor phase disconnected or stator open circuit i58; inverter senses missing phase current.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Arthur Martin (Arthur Martin ASF Series / Calypso / Electrolux Luxe Dishwasher) models: Cut wire in three-phase motor cable harness, terminal pin backed out of plastic housing, or open stator winding inside motor.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Test electrical continuity of each phase lead from inverter board to motor terminals (< 0.5 Ω). Replace motor if winding is open (infinite Ω). Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Arthur Martin Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrive Motor, Inverter & Tachometer SensorDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

3Ω–6Ω (BLDC phase U-V-W) / 60Ω–180Ω (Tacho coil) / 1.5Ω–3.5Ω (Universal stator)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:3-Phase Motor Windings / Tacho Generator / Carbon Brushes

Test Pins & Connections

PROBE (+)

PROBE (-)

Across phase pins U-V, V-W, U-W on motor harness; across tacho pins

Tolerance & Diagnostic CriteriaBLDC phase winding values must be strictly balanced within ±0.3Ω. Hand rotation generates 1V–4V AC on tacho.

1. Pre-Intervention Electrical Safety Protocols

!High-Voltage Safety Protocol & DC Bus: Wait at least 5 minutes after power cutoff to allow inverter DC bus capacitors (380V DC) to bleed down.
!Verify 0V DC across inverter filter capacitors before unplugging motor harness connectors.
!Keep hands clear of drive belt and pulleys during any manual rotation tng.

3. Preliminary Mechanical & Visual Checks

Slip off drive belt and spin drum/motor shaft by hand to check for roaring or seized ball bearings.
For universal motors: verify carbon brushes have at least 10mm remaining length and smooth contact faces.
Inspect motor suspension rubber mounts and drive belt tension/groove profile.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Arthur Martin I58

FAQ TREE

What does error code I58 mean on a Arthur Martin appliance?

Arthur Martin error code I58 indicates: Arthur Martin ASF Series / Calypso / Electrolux Luxe Dishwasher: Circulation pump motor phase disconnected or stator open circuit i58; inverter senses missing phase current..

What is the root cause of Arthur Martin error code I58?

The primary root cause for Arthur Martin code I58 is: On Arthur Martin (Arthur Martin ASF Series / Calypso / Electrolux Luxe Dishwasher) models: Cut wire in three-phase motor cable harness, terminal pin backed out of plastic housing, or open stator winding inside motor..

How do I fix or resolve Arthur Martin error code I58?

To resolve error code I58: Test electrical continuity of each phase lead from inverter board to motor terminals (< 0.5 Ω). Replace motor if winding is open (infinite Ω). Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

Is it safe to clear Arthur Martin error code I58 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Arthur Martin code I58 persists, the physical component causing On Arthur Martin (Arthur Martin ASF Series / Calypso / Electrolux Luxe Dishwasher) models: Cut wire in three-phase motor cable harness, terminal pin backed out of plastic housing, or open stator winding inside motor. must be inspected or replaced.

How do I test electrical resistance for Arthur Martin code I58 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test 3-Phase Motor Windings / Tacho Generator / Carbon Brushes across Across phase pins U-V, V-W, U-W on motor harness; across tacho pins. Expected nominal reading is 3Ω–6Ω (BLDC phase U-V-W) / 60Ω–180Ω (Tacho coil) / 1.5Ω–3.5Ω (Universal stator). Tolerance: BLDC phase winding values must be strictly balanced within ±0.3Ω. Hand rotation generates 1V–4V AC on tacho..

What safety protocol must be followed before servicing Arthur Martin code I58?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEi58

Arthur Martin // OFFICIAL DIAGNOSTIC BENCH

Arthur Martin i58

DishwasherDrive Motor, Inverter & Tachometer Sensor

Dishwasher

Other Brands Sharing Code i58:ElectroluxI58 AEGI58 ZanussiI58 CastorI58 FaureI58 FrigidaireI58 KelvinatorI58 WestinghouseI58 ZoppasI58

Symptom / Description

FAULT

Arthur Martin ASF Series / Calypso / Electrolux Luxe Dishwasher: Circulation pump motor phase disconnected or stator open circuit i58; inverter senses missing phase current.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Arthur Martin Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrive Motor, Inverter & Tachometer SensorDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

3Ω–6Ω (BLDC phase U-V-W) / 60Ω–180Ω (Tacho coil) / 1.5Ω–3.5Ω (Universal stator)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:3-Phase Motor Windings / Tacho Generator / Carbon Brushes

Test Pins & Connections

PROBE (+)

PROBE (-)

Across phase pins U-V, V-W, U-W on motor harness; across tacho pins

Tolerance & Diagnostic CriteriaBLDC phase winding values must be strictly balanced within ±0.3Ω. Hand rotation generates 1V–4V AC on tacho.

1. Pre-Intervention Electrical Safety Protocols

!High-Voltage Safety Protocol & DC Bus: Wait at least 5 minutes after power cutoff to allow inverter DC bus capacitors (380V DC) to bleed down.
!Verify 0V DC across inverter filter capacitors before unplugging motor harness connectors.
!Keep hands clear of drive belt and pulleys during any manual rotation tng.

3. Preliminary Mechanical & Visual Checks

Slip off drive belt and spin drum/motor shaft by hand to check for roaring or seized ball bearings.
For universal motors: verify carbon brushes have at least 10mm remaining length and smooth contact faces.
Inspect motor suspension rubber mounts and drive belt tension/groove profile.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Arthur Martin I58

FAQ TREE

What does error code I58 mean on a Arthur Martin appliance?

What is the root cause of Arthur Martin error code I58?

How do I fix or resolve Arthur Martin error code I58?

Is it safe to clear Arthur Martin error code I58 by resetting power?

How do I test electrical resistance for Arthur Martin code I58 using a multimeter?

What safety protocol must be followed before servicing Arthur Martin code I58?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Arthur Martin i58

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Arthur Martin I58

Community Verification

Related Arthur Martin Dishwasher Error Codes

Arthur Martin i58

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Arthur Martin I58

Community Verification

Related Arthur Martin Dishwasher Error Codes