OEM VERIFIED BENCH

OFFICIAL FAULT CODEE16

Bosch // OFFICIAL DIAGNOSTIC BENCH

Bosch E16

DishwasherDrainage System & Drain Pump

Dishwasher

Other Brands Sharing Code E16:CandyE16 NeffE16 HooverE16 RosieresE16 AirluxE16 IbernaE16 NardiE16 SangiorgioE16 SiltalE16 ZerowattE16

Symptom / Description

FAULT

Water loading (impulses from flow meter) without solenoid valve control or appliance recognizes impulses from tachometric generator although no water is loaded (cycle interrupted with drain)

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

Defective PCB Power Supply Rails & DC Bus Filter Capacitors, open/short circuit in the wiring harness, or faulty connector on the electronic control board (pcb) & bus communications.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Check the loading valve and its control. Check the loading solenoid valve.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Bosch Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Bosch E16

FAQ TREE

What does error code E16 mean on a Bosch appliance?

Bosch error code E16 indicates: Water loading (impulses from flow meter) without solenoid valve control or appliance recognizes impulses from tachometric generator although no water is loaded (cycle interrupted with drain).

What is the root cause of Bosch error code E16?

The primary root cause for Bosch code E16 is: Defective PCB Power Supply Rails & DC Bus Filter Capacitors, open/short circuit in the wiring harness, or faulty connector on the electronic control board (pcb) & bus communications..

How do I fix or resolve Bosch error code E16?

To resolve error code E16: Check the loading valve and its control. Check the loading solenoid valve.

Is it safe to clear Bosch error code E16 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Bosch code E16 persists, the physical component causing Defective PCB Power Supply Rails & DC Bus Filter Capacitors, open/short circuit in the wiring harness, or faulty connector on the electronic control board (pcb) & bus communications. must be inspected or replaced.

How do I test electrical resistance for Bosch code E16 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Drain Pump Motor Stator Coils across Across pump motor spade terminals (L-N unclipped). Expected nominal reading is 160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC). Tolerance: ±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ..

What safety protocol must be followed before servicing Bosch code E16?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEE16

Bosch // OFFICIAL DIAGNOSTIC BENCH

Bosch E16

DishwasherDrainage System & Drain Pump

Dishwasher

Other Brands Sharing Code E16:CandyE16 NeffE16 HooverE16 RosieresE16 AirluxE16 IbernaE16 NardiE16 SangiorgioE16 SiltalE16 ZerowattE16

Symptom / Description

FAULT

Water loading (impulses from flow meter) without solenoid valve control or appliance recognizes impulses from tachometric generator although no water is loaded (cycle interrupted with drain)

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

Defective PCB Power Supply Rails & DC Bus Filter Capacitors, open/short circuit in the wiring harness, or faulty connector on the electronic control board (pcb) & bus communications.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Check the loading valve and its control. Check the loading solenoid valve.

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Bosch Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Bosch E16

FAQ TREE

What does error code E16 mean on a Bosch appliance?

What is the root cause of Bosch error code E16?

How do I fix or resolve Bosch error code E16?

To resolve error code E16: Check the loading valve and its control. Check the loading solenoid valve.

Is it safe to clear Bosch error code E16 by resetting power?

How do I test electrical resistance for Bosch code E16 using a multimeter?

What safety protocol must be followed before servicing Bosch code E16?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Bosch E16

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Bosch E16

Community Verification

Related Bosch Dishwasher Error Codes

Bosch E16

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Bosch E16

Community Verification

Related Bosch Dishwasher Error Codes