OEM VERIFIED BENCH

OFFICIAL FAULT CODEE42

Faure // OFFICIAL DIAGNOSTIC BENCH

Faure E42

Washing MachineDrainage System & Drain Pump

Washing Machine

Other Brands Sharing Code E42:ElectroluxE42 AEGE42 ZanussiE42 Arthur MartinE42 CastorE42 FrigidaireE42 KelvinatorE42 WestinghouseE42 ZoppasE42

Symptom / Description

FAULT

Faure FWG / FWF Series / Magic'45 Compact Washer: Door unlocking aperture failure E42; door interlock fails to release latch mechanism after cycle completes.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Faure (Faure FWG / FWF Series / Magic'45 Compact Washer) models: PTC bi-metal strip failed to cool down, mechanical bimetal latch jammed, or instant pulse unlock solenoid coil open circuit (nominal 120–250 Ω).

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Wait 3 minutes for bi-metal to cool. If still locked, use manual emergency release cord located behind drain filter flap. Replace door interlock. Press and hold Départ/Pause and Annulation buttons for 6 seconds until all status indicators flash synchronously and clear fault memory.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Faure Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpWashing Machine

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Faure E42

FAQ TREE

What does error code E42 mean on a Faure appliance?

Faure error code E42 indicates: Faure FWG / FWF Series / Magic'45 Compact Washer: Door unlocking aperture failure E42; door interlock fails to release latch mechanism after cycle completes..

What is the root cause of Faure error code E42?

The primary root cause for Faure code E42 is: On Faure (Faure FWG / FWF Series / Magic'45 Compact Washer) models: PTC bi-metal strip failed to cool down, mechanical bimetal latch jammed, or instant pulse unlock solenoid coil open circuit (nominal 120–250 Ω)..

How do I fix or resolve Faure error code E42?

To resolve error code E42: Wait 3 minutes for bi-metal to cool. If still locked, use manual emergency release cord located behind drain filter flap. Replace door interlock. Press and hold Départ/Pause and Annulation buttons for 6 seconds until all status indicators flash synchronously and clear fault memory.

Is it safe to clear Faure error code E42 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Faure code E42 persists, the physical component causing On Faure (Faure FWG / FWF Series / Magic'45 Compact Washer) models: PTC bi-metal strip failed to cool down, mechanical bimetal latch jammed, or instant pulse unlock solenoid coil open circuit (nominal 120–250 Ω). must be inspected or replaced.

How do I test electrical resistance for Faure code E42 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Drain Pump Motor Stator Coils across Across pump motor spade terminals (L-N unclipped). Expected nominal reading is 160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC). Tolerance: ±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ..

What safety protocol must be followed before servicing Faure code E42?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEE42

Faure // OFFICIAL DIAGNOSTIC BENCH

Faure E42

Washing MachineDrainage System & Drain Pump

Washing Machine

Other Brands Sharing Code E42:ElectroluxE42 AEGE42 ZanussiE42 Arthur MartinE42 CastorE42 FrigidaireE42 KelvinatorE42 WestinghouseE42 ZoppasE42

Symptom / Description

FAULT

Faure FWG / FWF Series / Magic'45 Compact Washer: Door unlocking aperture failure E42; door interlock fails to release latch mechanism after cycle completes.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Faure Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpWashing Machine

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Faure E42

FAQ TREE

What does error code E42 mean on a Faure appliance?

Faure error code E42 indicates: Faure FWG / FWF Series / Magic'45 Compact Washer: Door unlocking aperture failure E42; door interlock fails to release latch mechanism after cycle completes..

What is the root cause of Faure error code E42?

How do I fix or resolve Faure error code E42?

Is it safe to clear Faure error code E42 by resetting power?

How do I test electrical resistance for Faure code E42 using a multimeter?

What safety protocol must be followed before servicing Faure code E42?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Faure E42

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Faure E42

Community Verification

Related Faure Washing Machine Error Codes

Faure E42

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Faure E42

Community Verification

Related Faure Washing Machine Error Codes