Skip to content
CodesErreur.comSWISS PRO ENGINE
Core Diagnostics
DiagnosticsBrandsOEM ManualsSpecialistsAI EngineerPRO
Workshop Tools
Diagnostic ToolsNEW
Hardware interfaces & test probes
Find Rating Plate
Locate exact E-Nr, PNC & serial codes
Parts Locator
Global OEM spare parts suppliers
Community & Career
Academy & Courses
Masterclasses by senior technicians
Certification ExamsPRO
Verify your B2B technical credentials
Elite Forum
Peer-to-peer field troubleshooting
Tech Jobs
B2B recruitment & field opportunities
Leaderboard
Global ranking of verified specialists
Certified Appliance Engineering EcosystemApply for Certification →
Language Selector
Account & Access
Upgrade PRO
Back to Search
OEM VERIFIED BENCH
OFFICIAL FAULT CODEE02
Fors
Fors // OFFICIAL DIAGNOSTIC BENCH

Fors E02

Washing MachineWater Inlet Valve, Aquastop & Flowmeter
Luxury front-loading washing machine in brushed titanium with illuminated dark glass drum
Washing Machine
Other Brands Sharing Code E02:BoschE02ElectroluxE02AEGE02CandyE02HooverE02ZanussiE02Arthur MartinE02GaggenauE02RosieresE02Schaub LorenzE02

Symptom / Description

FAULT

Machine is not filling with water or filling very slowly.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

Low water pressure, a kinked inlet hose, or a faulty water inlet valve.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED
1Ensure the water tap is fully open. Check the inlet hose for kinks or blockages. Clean the filter inside the inlet valve. Replace the valve if it's defective.
AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time
AI WORKSHOP PROTOCOL ENGINE
Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH
Need Help? Call a Certified TechnicianWorldwide Fors Parts Finder
Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLWater Inlet Valve, Aquastop & FlowmeterWashing Machine
2. Multimeter & Electrical Bench Tests (Ω)
MODE: OHMMETER (Ω)AUTO-RANGE
Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board
CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)
Nominal Resistance (Ω)
3.5kΩ–4.5kΩ (Standard 230V) / 2.0kΩ–4.2kΩ (Aquastop)NOMINAL
0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)
▲ NOMINAL OPERATING WINDOW
Target Component:Solenoid Valve Coil / Aquastop Pneumatic Valve
Test Pins & Connections
PROBE (+)
PROBE (-)
Across coil spade terminals (disconnect harness first)
Tolerance & Diagnostic Criteria±10%. Open circuit (OL) indicates burned solenoid coil. Flowmeter turbine reed switch pulses on flow.
1. Pre-Intervention Electrical Safety Protocols
  • !Electrical Safety Protocol: Disconnect electrical power before touching solenoid valve coils or Aquastop connectors.
  • !Firmly shut off the domc water supply tap before unscrewing the inlet hose fitting.
  • !Check safety base drip tray for accumulated water triggering the anti-flood polystyrene float switch.
3. Preliminary Mechanical & Visual Checks
  • Remove and clean sediment and sand particles from the 3/4" inlet hose metal mesh filter.
  • Verify domestic dynamic water pressure is between 1.0 and 10.0 bar (0.1 to 1.0 MPa).
  • Inspect outer Aquastop hose jacket for expansion, pinch damage, or internal leak reservoir triggering.
Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Fors E02

FAQ TREE
What does error code E02 mean on a Fors appliance?

Fors error code E02 indicates: Machine is not filling with water or filling very slowly..

What is the root cause of Fors error code E02?

The primary root cause for Fors code E02 is: Low water pressure, a kinked inlet hose, or a faulty water inlet valve..

How do I fix or resolve Fors error code E02?

To resolve error code E02: Ensure the water tap is fully open. Check the inlet hose for kinks or blockages. Clean the filter inside the inlet valve. Replace the valve if it's defective.

Is it safe to clear Fors error code E02 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Fors code E02 persists, the physical component causing Low water pressure, a kinked inlet hose, or a faulty water inlet valve. must be inspected or replaced.

How do I test electrical resistance for Fors code E02 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Solenoid Valve Coil / Aquastop Pneumatic Valve across Across coil spade terminals (disconnect harness first). Expected nominal reading is 3.5kΩ–4.5kΩ (Standard 230V) / 2.0kΩ–4.2kΩ (Aquastop). Tolerance: ±10%. Open circuit (OL) indicates burned solenoid coil. Flowmeter turbine reed switch pulses on flow..

What safety protocol must be followed before servicing Fors code E02?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

SEMANTIC KNOWLEDGE GRAPH // FORS

Related Fors Washing Machine Error Codes

Diagnostic Link Mesh14 OEM Cross-References

Cross-referenced diagnostic codes for technicians inspecting similar component subsystems.

E03Drainage System & Drain Pump
Machine is not draining water or pump runs continuously.
Inspect Protocol
E04Water Level Pressure Switch & Air Dome
Machine has overfilled with water, potential for leaking.
Inspect Protocol
E05NTC Temperature Sensor & Thermistor
Water is not heating up during the wash cycle.
Inspect Protocol
E06Drive Motor, Inverter & Tachometer Sensor
The drum is not turning or spinning.
Inspect Protocol
E08Drive Motor, Inverter & Tachometer Sensor
Drum may spin uncontrollably to high speed or not at all.
Inspect Protocol
E10Electronic Control Board (PCB) & Bus Communications
Machine stops mid-cycle, display may flash or be unresponsive.
Inspect Protocol
E21Drainage System & Drain Pump
Drainage is slow or incomplete.
Inspect Protocol
E01Door Lock Mechanism & Safety Interlock
Door cannot be locked or machine won't start.
Inspect Protocol
E1General System & Mechanical Integration
The hob shuts down during use.
Inspect Protocol
E2General System & Mechanical Integration
A specific cooking zone shuts down.
Inspect Protocol
E3General System & Mechanical Integration
The hob does not turn on or shows an error immediately.
Inspect Protocol
E4Refrigeration Compressor, Defrost Heater & PTC Relay
Refrigerator is not cooling properly and there is a large ice block behind the back panel.
Inspect Protocol
E6Electronic Control Board (PCB) & Bus Communications
One side of the induction hob (usually two zones) is not working.
Inspect Protocol
FGeneral System & Mechanical Integration
A cooking zone will not turn on, and 'F' is flashing on its display.
Inspect Protocol
CodesErreur.com

Premium appliance diagnostics & repair database.
Powered by AI to help certified technicians worldwide.

Trusted by professionals in CH & FR

Platform

Search DatabasePRO Diagnostic AIPRODiagnostic ToolsBrands

Workshop Tools

Brands (87)OEM ManualsFind Rating PlateParts Locator

For Technicians

SpecialistsTechnician ForumTech JobsPremium

Corporate

Terms of ServicePrivacy PolicyOfficial Swiss Repair Partner: Electroassistance
OPERATIONAL SAFETY SPECIFICATION

SAFETY DISCLAIMER

The technical information, diagnostic guides, error codes, and AI-generated suggestions provided on this website are intended exclusively for certified and qualified professionals. Appliance repair involves severe electrical hazards, high voltages, and mechanical risks that can result in fatal injury or severe property damage. If you are not a trained technician, do not attempt to repair any appliances. CodesErreur assumes no responsibility or liability for any damage, injury, or consequential losses resulting from the use of the information provided on this platform. You use all information entirely at your own risk.

© 2026 CodesErreur. All rights reserved.

Official Swiss Repair Partner: Electroassistance Terms of Service Privacy Policy