OEM VERIFIED BENCH

OFFICIAL FAULT CODELDS-10

H-Koenig // OFFICIAL DIAGNOSTIC BENCH

H-Koenig Robot Vacuum LDS-10

Q: What does error code LDS-10 mean on a H.Koenig appliance?

H.Koenig error code LDS-10 indicates: H.Koenig SWRC90 / SWRC110 / WaterMop Laser LDS Smart Robotic Vacuum & Mop: Diagnostic fault code LDS-10 registered by the microcomputer controller. BLDC brushless suction vacuum turbine fan motor overcurrent or driver trip.

Q: What is the root cause of H.Koenig error code LDS-10?

The primary root cause for H.Koenig code LDS-10 is: On H.Koenig appliances engineered with 360° laser LDS distance turret (5-8 Hz), twin DC wheel drive motors with encoders, 20W BLDC suction fan, and 14.8V 2600mAh lithium battery with thermal cut-off: wet liquid sucked into high-speed turbine (20000 RPM) causing shorted stator winding Metrological tolerance verification: BLDC turbine 3-phase resistance 2.2 Ω to 3.8 Ω balanced; running current 0.8A to 2.4A..

Q: How do I fix or resolve H.Koenig error code LDS-10?

To resolve error code LDS-10: Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: check exhaust duct for wet sludge; measure motor phase resistance; replace suction motor. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: turn off the mechanical master rocker switch under the chassis, clean optical cliff sensors and wheel hubs, place robot on charging dock, and hold Auto for 5 seconds.

Q: Is it safe to clear H.Koenig error code LDS-10 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if H.Koenig code LDS-10 persists, the physical component causing On H.Koenig appliances engineered with 360° laser LDS distance turret (5-8 Hz), twin DC wheel drive motors with encoders, 20W BLDC suction fan, and 14.8V 2600mAh lithium battery with thermal cut-off: wet liquid sucked into high-speed turbine (20000 RPM) causing shorted stator winding Metrological tolerance verification: BLDC turbine 3-phase resistance 2.2 Ω to 3.8 Ω balanced; running current 0.8A to 2.4A. must be inspected or replaced.

Q: How do I test electrical resistance for H.Koenig code LDS-10 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Drain Pump Motor Stator Coils across Across pump motor spade terminals (L-N unclipped). Expected nominal reading is 160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC). Tolerance: ±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ..

Q: What safety protocol must be followed before servicing H.Koenig code LDS-10?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Robot VacuumDrainage System & Drain Pump

Luxury front-loading washing machine in brushed titanium with illuminated dark glass drum

Robot Vacuum

Symptom / Description

FAULT

H.Koenig SWRC90 / SWRC110 / WaterMop Laser LDS Smart Robotic Vacuum & Mop: Diagnostic fault code LDS-10 registered by the microcomputer controller. BLDC brushless suction vacuum turbine fan motor overcurrent or driver trip

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On H.Koenig appliances engineered with 360° laser LDS distance turret (5-8 Hz), twin DC wheel drive motors with encoders, 20W BLDC suction fan, and 14.8V 2600mAh lithium battery with thermal cut-off: wet liquid sucked into high-speed turbine (20000 RPM) causing shorted stator winding Metrological tolerance verification: BLDC turbine 3-phase resistance 2.2 Ω to 3.8 Ω balanced; running current 0.8A to 2.4A.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: check exhaust duct for wet sludge; measure motor phase resistance; replace suction motor. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: turn off the mechanical master rocker switch under the chassis, clean optical cliff sensors and wheel hubs, place robot on charging dock, and hold Auto for 5 seconds.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide H-Koenig Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

SWISS ATELIER TECHNICAL BLUEPRINT // 2026 SCHEMATIC STANDARD

Hydraulic & Drainage Loop

Drain Pump M2, Impeller Chamber, Sump Filter & Analog Pressostat

CALIBRATED TEST POINTS (TP1 / TP2)

ACTIVE MULTIMETER BENCH

Target Component

Drain Pump Motor Stator Coils

Nominal Resistance / Test Range

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)

Test Harness Pins

Across pump motor spade terminals (L-N unclipped)

Diagnostic Verification Rule

Measure coil resistance unplugged. If OL (open loop) or < 50 Ω (shorted), replace pump assembly.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpHousehold Appliance

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: H-Koenig LDS-10

FAQ TREE

What does error code LDS-10 mean on a H.Koenig appliance?

H.Koenig error code LDS-10 indicates: H.Koenig SWRC90 / SWRC110 / WaterMop Laser LDS Smart Robotic Vacuum & Mop: Diagnostic fault code LDS-10 registered by the microcomputer controller. BLDC brushless suction vacuum turbine fan motor overcurrent or driver trip.

What is the root cause of H.Koenig error code LDS-10?

The primary root cause for H.Koenig code LDS-10 is: On H.Koenig appliances engineered with 360° laser LDS distance turret (5-8 Hz), twin DC wheel drive motors with encoders, 20W BLDC suction fan, and 14.8V 2600mAh lithium battery with thermal cut-off: wet liquid sucked into high-speed turbine (20000 RPM) causing shorted stator winding Metrological tolerance verification: BLDC turbine 3-phase resistance 2.2 Ω to 3.8 Ω balanced; running current 0.8A to 2.4A..

How do I fix or resolve H.Koenig error code LDS-10?

To resolve error code LDS-10: Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: check exhaust duct for wet sludge; measure motor phase resistance; replace suction motor. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: turn off the mechanical master rocker switch under the chassis, clean optical cliff sensors and wheel hubs, place robot on charging dock, and hold Auto for 5 seconds.

Is it safe to clear H.Koenig error code LDS-10 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if H.Koenig code LDS-10 persists, the physical component causing On H.Koenig appliances engineered with 360° laser LDS distance turret (5-8 Hz), twin DC wheel drive motors with encoders, 20W BLDC suction fan, and 14.8V 2600mAh lithium battery with thermal cut-off: wet liquid sucked into high-speed turbine (20000 RPM) causing shorted stator winding Metrological tolerance verification: BLDC turbine 3-phase resistance 2.2 Ω to 3.8 Ω balanced; running current 0.8A to 2.4A. must be inspected or replaced.

How do I test electrical resistance for H.Koenig code LDS-10 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Drain Pump Motor Stator Coils across Across pump motor spade terminals (L-N unclipped). Expected nominal reading is 160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC). Tolerance: ±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ..

What safety protocol must be followed before servicing H.Koenig code LDS-10?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODELDS-10

H-Koenig // OFFICIAL DIAGNOSTIC BENCH

H-Koenig Robot Vacuum LDS-10

Robot VacuumDrainage System & Drain Pump

Robot Vacuum

Symptom / Description

FAULT

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide H-Koenig Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

SWISS ATELIER TECHNICAL BLUEPRINT // 2026 SCHEMATIC STANDARD

Hydraulic & Drainage Loop

Drain Pump M2, Impeller Chamber, Sump Filter & Analog Pressostat

CALIBRATED TEST POINTS (TP1 / TP2)

ACTIVE MULTIMETER BENCH

Target Component

Drain Pump Motor Stator Coils

Nominal Resistance / Test Range

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)

Test Harness Pins

Across pump motor spade terminals (L-N unclipped)

Diagnostic Verification Rule

Measure coil resistance unplugged. If OL (open loop) or < 50 Ω (shorted), replace pump assembly.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpHousehold Appliance

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: H-Koenig LDS-10

FAQ TREE

What does error code LDS-10 mean on a H.Koenig appliance?

What is the root cause of H.Koenig error code LDS-10?

How do I fix or resolve H.Koenig error code LDS-10?

Is it safe to clear H.Koenig error code LDS-10 by resetting power?

How do I test electrical resistance for H.Koenig code LDS-10 using a multimeter?

What safety protocol must be followed before servicing H.Koenig code LDS-10?

Community Verification

COMMUNITY

Did this solution resolve the issue?

H-Koenig Robot Vacuum LDS-10

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Hydraulic & Drainage Loop

Workshop Verification & Safety Checklist

Frequently Asked Questions: H-Koenig LDS-10

Community Verification

Related H.Koenig Appliance Error Codes

H-Koenig Robot Vacuum LDS-10

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Hydraulic & Drainage Loop

Workshop Verification & Safety Checklist

Frequently Asked Questions: H-Koenig LDS-10

Community Verification

Related H.Koenig Appliance Error Codes