OEM VERIFIED BENCH

OFFICIAL FAULT CODEE10

Haier // OFFICIAL DIAGNOSTIC BENCH

Haier E10

DishwasherDrive Motor, Inverter & Tachometer Sensor

Dishwasher

Select Appliance Type

0ms Instant Telemetry Switch

Other Brands Sharing Code E10:BoschE10 SiemensE10 SamsungE10 LGE10 ElectroluxE10 AEGE10 BekoE10 CandyE10 NeffE10 V-ZugE10

Symptom / Description

FAULT

Haier I-Pro Shine / Washlogix Ultra Silence Dishwasher: Water diverter valve timeout E10; motorized spray arm alternator disc fails to reach requested position microswitch contact.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Haier dishwashers utilizing I-Pro Shine Ultra Silence brushless wash circulation pump, dual-zone inverter spray system, and micro-filtration: Jammed ceramic disc in diverter body, open synchronous drive motor winding (~4–9 kΩ), or defective microswitch.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Measure synchronous motor winding resistance (~4–9 kΩ). Verify cam microswitch continuity when actuated. Inspect diverter disc for foreign matter. Press Power button off, hold Half Load and Start buttons together while powering on until diagnostic test mode 01 displays, then power off.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Haier Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrive Motor, Inverter & Tachometer SensorDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

3Ω–6Ω (BLDC phase U-V-W) / 60Ω–180Ω (Tacho coil) / 1.5Ω–3.5Ω (Universal stator)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:3-Phase Motor Windings / Tacho Generator / Carbon Brushes

Test Pins & Connections

PROBE (+)

PROBE (-)

Across phase pins U-V, V-W, U-W on motor harness; across tacho pins

Tolerance & Diagnostic CriteriaBLDC phase winding values must be strictly balanced within ±0.3Ω. Hand rotation generates 1V–4V AC on tacho.

1. Pre-Intervention Electrical Safety Protocols

!High-Voltage Safety Protocol & DC Bus: Wait at least 5 minutes after power cutoff to allow inverter DC bus capacitors (380V DC) to bleed down.
!Verify 0V DC across inverter filter capacitors before unplugging motor harness connectors.
!Keep hands clear of drive belt and pulleys during any manual rotation tng.

3. Preliminary Mechanical & Visual Checks

Slip off drive belt and spin drum/motor shaft by hand to check for roaring or seized ball bearings.
For universal motors: verify carbon brushes have at least 10mm remaining length and smooth contact faces.
Inspect motor suspension rubber mounts and drive belt tension/groove profile.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Haier E10

FAQ TREE

What does error code E10 mean on a Haier appliance?

Haier error code E10 indicates: Haier I-Pro Shine / Washlogix Ultra Silence Dishwasher: Water diverter valve timeout E10; motorized spray arm alternator disc fails to reach requested position microswitch contact..

What is the root cause of Haier error code E10?

The primary root cause for Haier code E10 is: On Haier dishwashers utilizing I-Pro Shine Ultra Silence brushless wash circulation pump, dual-zone inverter spray system, and micro-filtration: Jammed ceramic disc in diverter body, open synchronous drive motor winding (~4–9 kΩ), or defective microswitch..

How do I fix or resolve Haier error code E10?

To resolve error code E10: Measure synchronous motor winding resistance (~4–9 kΩ). Verify cam microswitch continuity when actuated. Inspect diverter disc for foreign matter. Press Power button off, hold Half Load and Start buttons together while powering on until diagnostic test mode 01 displays, then power off.

Is it safe to clear Haier error code E10 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Haier code E10 persists, the physical component causing On Haier dishwashers utilizing I-Pro Shine Ultra Silence brushless wash circulation pump, dual-zone inverter spray system, and micro-filtration: Jammed ceramic disc in diverter body, open synchronous drive motor winding (~4–9 kΩ), or defective microswitch. must be inspected or replaced.

How do I test electrical resistance for Haier code E10 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test 3-Phase Motor Windings / Tacho Generator / Carbon Brushes across Across phase pins U-V, V-W, U-W on motor harness; across tacho pins. Expected nominal reading is 3Ω–6Ω (BLDC phase U-V-W) / 60Ω–180Ω (Tacho coil) / 1.5Ω–3.5Ω (Universal stator). Tolerance: BLDC phase winding values must be strictly balanced within ±0.3Ω. Hand rotation generates 1V–4V AC on tacho..

What safety protocol must be followed before servicing Haier code E10?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEE10

Haier // OFFICIAL DIAGNOSTIC BENCH

Haier E10

DishwasherDrive Motor, Inverter & Tachometer Sensor

Dishwasher

Select Appliance Type

0ms Instant Telemetry Switch

Other Brands Sharing Code E10:BoschE10 SiemensE10 SamsungE10 LGE10 ElectroluxE10 AEGE10 BekoE10 CandyE10 NeffE10 V-ZugE10

Symptom / Description

FAULT

Haier I-Pro Shine / Washlogix Ultra Silence Dishwasher: Water diverter valve timeout E10; motorized spray arm alternator disc fails to reach requested position microswitch contact.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Haier Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrive Motor, Inverter & Tachometer SensorDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

3Ω–6Ω (BLDC phase U-V-W) / 60Ω–180Ω (Tacho coil) / 1.5Ω–3.5Ω (Universal stator)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:3-Phase Motor Windings / Tacho Generator / Carbon Brushes

Test Pins & Connections

PROBE (+)

PROBE (-)

Across phase pins U-V, V-W, U-W on motor harness; across tacho pins

Tolerance & Diagnostic CriteriaBLDC phase winding values must be strictly balanced within ±0.3Ω. Hand rotation generates 1V–4V AC on tacho.

1. Pre-Intervention Electrical Safety Protocols

!High-Voltage Safety Protocol & DC Bus: Wait at least 5 minutes after power cutoff to allow inverter DC bus capacitors (380V DC) to bleed down.
!Verify 0V DC across inverter filter capacitors before unplugging motor harness connectors.
!Keep hands clear of drive belt and pulleys during any manual rotation tng.

3. Preliminary Mechanical & Visual Checks

Slip off drive belt and spin drum/motor shaft by hand to check for roaring or seized ball bearings.
For universal motors: verify carbon brushes have at least 10mm remaining length and smooth contact faces.
Inspect motor suspension rubber mounts and drive belt tension/groove profile.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Haier E10

FAQ TREE

What does error code E10 mean on a Haier appliance?

What is the root cause of Haier error code E10?

How do I fix or resolve Haier error code E10?

Is it safe to clear Haier error code E10 by resetting power?

How do I test electrical resistance for Haier code E10 using a multimeter?

What safety protocol must be followed before servicing Haier code E10?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Haier E10

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Haier E10

Community Verification

Related Haier Dishwasher Error Codes

Haier E10

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Haier E10

Community Verification

Related Haier Dishwasher Error Codes