OEM VERIFIED BENCH

OFFICIAL FAULT CODEFA

Ignis // OFFICIAL DIAGNOSTIC BENCH

Ignis FA

DishwasherDrainage System & Drain Pump

Dishwasher

Other Brands Sharing Code FA:WhirlpoolFA IndesitFA BauknechtFA AristonFA PhilipsFA AirluxFA Gree / MaceFA HotpointFA

Symptom / Description

FAULT

Ignis ADL & TuttoinUno Platinum Compact Dishwasher: Optical Water Indicator (OWI) turbidity sensor failure FA; infra-red optoelectronic receiver signal distorted or disconnected.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Ignis dishwashers: Soil deposition on OWI prism lenses, defective phototransistor diode, or wiring harness disconnect on base sump interface.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Clean optical prism face of OWI sensor inside sump. Verify 5V DC supply and signal line to main board. Replace OWI sensor assembly if cleaning fails. Press and hold Start button for 5 seconds to force drain cycle, wait 60s, then switch off power switch.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Ignis Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Ignis FA

FAQ TREE

What does error code FA mean on a Ignis appliance?

Ignis error code FA indicates: Ignis ADL & TuttoinUno Platinum Compact Dishwasher: Optical Water Indicator (OWI) turbidity sensor failure FA; infra-red optoelectronic receiver signal distorted or disconnected..

What is the root cause of Ignis error code FA?

The primary root cause for Ignis code FA is: On Ignis dishwashers: Soil deposition on OWI prism lenses, defective phototransistor diode, or wiring harness disconnect on base sump interface..

How do I fix or resolve Ignis error code FA?

To resolve error code FA: Clean optical prism face of OWI sensor inside sump. Verify 5V DC supply and signal line to main board. Replace OWI sensor assembly if cleaning fails. Press and hold Start button for 5 seconds to force drain cycle, wait 60s, then switch off power switch.

Is it safe to clear Ignis error code FA by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Ignis code FA persists, the physical component causing On Ignis dishwashers: Soil deposition on OWI prism lenses, defective phototransistor diode, or wiring harness disconnect on base sump interface. must be inspected or replaced.

How do I test electrical resistance for Ignis code FA using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Drain Pump Motor Stator Coils across Across pump motor spade terminals (L-N unclipped). Expected nominal reading is 160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC). Tolerance: ±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ..

What safety protocol must be followed before servicing Ignis code FA?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEFA

Ignis // OFFICIAL DIAGNOSTIC BENCH

Ignis FA

DishwasherDrainage System & Drain Pump

Dishwasher

Other Brands Sharing Code FA:WhirlpoolFA IndesitFA BauknechtFA AristonFA PhilipsFA AirluxFA Gree / MaceFA HotpointFA

Symptom / Description

FAULT

Ignis ADL & TuttoinUno Platinum Compact Dishwasher: Optical Water Indicator (OWI) turbidity sensor failure FA; infra-red optoelectronic receiver signal distorted or disconnected.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Ignis dishwashers: Soil deposition on OWI prism lenses, defective phototransistor diode, or wiring harness disconnect on base sump interface.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Ignis Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Ignis FA

FAQ TREE

What does error code FA mean on a Ignis appliance?

What is the root cause of Ignis error code FA?

The primary root cause for Ignis code FA is: On Ignis dishwashers: Soil deposition on OWI prism lenses, defective phototransistor diode, or wiring harness disconnect on base sump interface..

How do I fix or resolve Ignis error code FA?

Is it safe to clear Ignis error code FA by resetting power?

How do I test electrical resistance for Ignis code FA using a multimeter?

What safety protocol must be followed before servicing Ignis code FA?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Ignis FA

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Ignis FA

Community Verification

Related Ignis Dishwasher Error Codes

Ignis FA

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Ignis FA

Community Verification

Related Ignis Dishwasher Error Codes