OEM VERIFIED BENCH

OFFICIAL FAULT CODEE19

Schulthess // OFFICIAL DIAGNOSTIC BENCH

Schulthess E19

Washing MachineWater Inlet Valve, Aquastop & Flowmeter

Washing Machine

Other Brands Sharing Code E19:BoschE19 SiemensE19 SamsungE19 LGE19 BekoE19 NeffE19 V-ZugE19 GaggenauE19 HisenseE19 AskoE19

Symptom / Description

FAULT

Schulthess Spirit / Champion / ProLine Swiss Engineering Washer: Hot water intake fault E19; secondary hot water inlet valve fails to supply water within allocated filling phase.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Schulthess washing machines featuring Spirit 3D washing motion, antibacterial profiles, heavy-duty Swiss suspension, and brushless inverter motor: Closed hot water tap, sediment-blocked hot inlet filter, or open hot solenoid coil (~3.6–4.6 kΩ).

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Check hot water tap supply. Clean the hot inlet hose mesh filter. Measure electrical resistance of hot solenoid coil (~3.6–4.6 kΩ). Press and hold the Start/Stop key for 5 seconds until the display shows '--:--'. Switch the master power button off, wait 30 seconds, and turn back on.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Schulthess Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLWater Inlet Valve, Aquastop & FlowmeterWashing Machine

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

3.5kΩ–4.5kΩ (Standard 230V) / 2.0kΩ–4.2kΩ (Aquastop)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Solenoid Valve Coil / Aquastop Pneumatic Valve

Test Pins & Connections

PROBE (+)

PROBE (-)

Across coil spade terminals (disconnect harness first)

Tolerance & Diagnostic Criteria±10%. Open circuit (OL) indicates burned solenoid coil. Flowmeter turbine reed switch pulses on flow.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Disconnect electrical power before touching solenoid valve coils or Aquastop connectors.
!Firmly shut off the domc water supply tap before unscrewing the inlet hose fitting.
!Check safety base drip tray for accumulated water triggering the anti-flood polystyrene float switch.

3. Preliminary Mechanical & Visual Checks

Remove and clean sediment and sand particles from the 3/4" inlet hose metal mesh filter.
Verify domestic dynamic water pressure is between 1.0 and 10.0 bar (0.1 to 1.0 MPa).
Inspect outer Aquastop hose jacket for expansion, pinch damage, or internal leak reservoir triggering.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Schulthess E19

FAQ TREE

What does error code E19 mean on a Schulthess appliance?

Schulthess error code E19 indicates: Schulthess Spirit / Champion / ProLine Swiss Engineering Washer: Hot water intake fault E19; secondary hot water inlet valve fails to supply water within allocated filling phase..

What is the root cause of Schulthess error code E19?

The primary root cause for Schulthess code E19 is: On Schulthess washing machines featuring Spirit 3D washing motion, antibacterial profiles, heavy-duty Swiss suspension, and brushless inverter motor: Closed hot water tap, sediment-blocked hot inlet filter, or open hot solenoid coil (~3.6–4.6 kΩ)..

How do I fix or resolve Schulthess error code E19?

To resolve error code E19: Check hot water tap supply. Clean the hot inlet hose mesh filter. Measure electrical resistance of hot solenoid coil (~3.6–4.6 kΩ). Press and hold the Start/Stop key for 5 seconds until the display shows '--:--'. Switch the master power button off, wait 30 seconds, and turn back on.

Is it safe to clear Schulthess error code E19 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Schulthess code E19 persists, the physical component causing On Schulthess washing machines featuring Spirit 3D washing motion, antibacterial profiles, heavy-duty Swiss suspension, and brushless inverter motor: Closed hot water tap, sediment-blocked hot inlet filter, or open hot solenoid coil (~3.6–4.6 kΩ). must be inspected or replaced.

How do I test electrical resistance for Schulthess code E19 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Solenoid Valve Coil / Aquastop Pneumatic Valve across Across coil spade terminals (disconnect harness first). Expected nominal reading is 3.5kΩ–4.5kΩ (Standard 230V) / 2.0kΩ–4.2kΩ (Aquastop). Tolerance: ±10%. Open circuit (OL) indicates burned solenoid coil. Flowmeter turbine reed switch pulses on flow..

What safety protocol must be followed before servicing Schulthess code E19?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEE19

Schulthess // OFFICIAL DIAGNOSTIC BENCH

Schulthess E19

Washing MachineWater Inlet Valve, Aquastop & Flowmeter

Washing Machine

Other Brands Sharing Code E19:BoschE19 SiemensE19 SamsungE19 LGE19 BekoE19 NeffE19 V-ZugE19 GaggenauE19 HisenseE19 AskoE19

Symptom / Description

FAULT

Schulthess Spirit / Champion / ProLine Swiss Engineering Washer: Hot water intake fault E19; secondary hot water inlet valve fails to supply water within allocated filling phase.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Schulthess Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLWater Inlet Valve, Aquastop & FlowmeterWashing Machine

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

3.5kΩ–4.5kΩ (Standard 230V) / 2.0kΩ–4.2kΩ (Aquastop)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Solenoid Valve Coil / Aquastop Pneumatic Valve

Test Pins & Connections

PROBE (+)

PROBE (-)

Across coil spade terminals (disconnect harness first)

Tolerance & Diagnostic Criteria±10%. Open circuit (OL) indicates burned solenoid coil. Flowmeter turbine reed switch pulses on flow.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Disconnect electrical power before touching solenoid valve coils or Aquastop connectors.
!Firmly shut off the domc water supply tap before unscrewing the inlet hose fitting.
!Check safety base drip tray for accumulated water triggering the anti-flood polystyrene float switch.

3. Preliminary Mechanical & Visual Checks

Remove and clean sediment and sand particles from the 3/4" inlet hose metal mesh filter.
Verify domestic dynamic water pressure is between 1.0 and 10.0 bar (0.1 to 1.0 MPa).
Inspect outer Aquastop hose jacket for expansion, pinch damage, or internal leak reservoir triggering.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Schulthess E19

FAQ TREE

What does error code E19 mean on a Schulthess appliance?

What is the root cause of Schulthess error code E19?

How do I fix or resolve Schulthess error code E19?

Is it safe to clear Schulthess error code E19 by resetting power?

How do I test electrical resistance for Schulthess code E19 using a multimeter?

What safety protocol must be followed before servicing Schulthess code E19?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Schulthess E19

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Schulthess E19

Community Verification

Related Schulthess Washing Machine Error Codes

Schulthess E19

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Schulthess E19

Community Verification

Related Schulthess Washing Machine Error Codes