OEM VERIFIED BENCH

OFFICIAL FAULT CODEE2

Sekom // OFFICIAL DIAGNOSTIC BENCH

Sekom E2

DishwasherDrainage System & Drain Pump

Dishwasher

Other Brands Sharing Code E2:BoschE2 SiemensE2 LGE2 WhirlpoolE2 ElectroluxE2 AEGE2 BekoE2 HaierE2 CandyE2 NeffE2

Symptom / Description

FAULT

Sekom E2: Water drainage failure detected in Dishwasher; drain pump cannot evacuate water within safety time limit.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

The dishwasher is unable to drain water within the specified time. Caused by blocked filters, a kinked drain hose, or a faulty drain pump.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Clean the main filter and microfilter inside the dishwasher. Check the drain hose for any kinks or blockages. Inspect the drain pump for obstructions.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Sekom Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Sekom E2

FAQ TREE

What does error code E2 mean on a Sekom appliance?

Sekom error code E2 indicates: Sekom E2: Water drainage failure detected in Dishwasher; drain pump cannot evacuate water within safety time limit..

What is the root cause of Sekom error code E2?

The primary root cause for Sekom code E2 is: The dishwasher is unable to drain water within the specified time. Caused by blocked filters, a kinked drain hose, or a faulty drain pump..

How do I fix or resolve Sekom error code E2?

To resolve error code E2: Clean the main filter and microfilter inside the dishwasher. Check the drain hose for any kinks or blockages. Inspect the drain pump for obstructions.

Is it safe to clear Sekom error code E2 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Sekom code E2 persists, the physical component causing The dishwasher is unable to drain water within the specified time. Caused by blocked filters, a kinked drain hose, or a faulty drain pump. must be inspected or replaced.

How do I test electrical resistance for Sekom code E2 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Drain Pump Motor Stator Coils across Across pump motor spade terminals (L-N unclipped). Expected nominal reading is 160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC). Tolerance: ±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ..

What safety protocol must be followed before servicing Sekom code E2?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEE2

Sekom // OFFICIAL DIAGNOSTIC BENCH

Sekom E2

DishwasherDrainage System & Drain Pump

Dishwasher

Other Brands Sharing Code E2:BoschE2 SiemensE2 LGE2 WhirlpoolE2 ElectroluxE2 AEGE2 BekoE2 HaierE2 CandyE2 NeffE2

Symptom / Description

FAULT

Sekom E2: Water drainage failure detected in Dishwasher; drain pump cannot evacuate water within safety time limit.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

The dishwasher is unable to drain water within the specified time. Caused by blocked filters, a kinked drain hose, or a faulty drain pump.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Clean the main filter and microfilter inside the dishwasher. Check the drain hose for any kinks or blockages. Inspect the drain pump for obstructions.

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Sekom Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Sekom E2

FAQ TREE

What does error code E2 mean on a Sekom appliance?

Sekom error code E2 indicates: Sekom E2: Water drainage failure detected in Dishwasher; drain pump cannot evacuate water within safety time limit..

What is the root cause of Sekom error code E2?

The primary root cause for Sekom code E2 is: The dishwasher is unable to drain water within the specified time. Caused by blocked filters, a kinked drain hose, or a faulty drain pump..

How do I fix or resolve Sekom error code E2?

To resolve error code E2: Clean the main filter and microfilter inside the dishwasher. Check the drain hose for any kinks or blockages. Inspect the drain pump for obstructions.

Is it safe to clear Sekom error code E2 by resetting power?

How do I test electrical resistance for Sekom code E2 using a multimeter?

What safety protocol must be followed before servicing Sekom code E2?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Sekom E2

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Sekom E2

Community Verification

Related Sekom Dishwasher Error Codes

Sekom E2

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Sekom E2

Community Verification

Related Sekom Dishwasher Error Codes