Skip to content
CodesErreur.comSWISS PRO ENGINE
Core Diagnostics
DiagnosticsBrandsOEM ManualsSpecialistsAI EngineerPRO
Workshop Tools
Diagnostic ToolsNEW
Hardware interfaces & test probes
Find Rating Plate
Locate exact E-Nr, PNC & serial codes
Parts Locator
Global OEM spare parts suppliers
Community & Career
Academy & Courses
Masterclasses by senior technicians
Certification ExamsPRO
Verify your B2B technical credentials
Elite Forum
Peer-to-peer field troubleshooting
Tech Jobs
B2B recruitment & field opportunities
Leaderboard
Global ranking of verified specialists
Certified Appliance Engineering EcosystemApply for Certification →
Language Selector
ENFRDEITESPT
ENEnglishFRFrançaisDEDeutschITItalianoESEspañolPTPortuguês
Account & Access
Upgrade PRO
Back to Search
OEM VERIFIED BENCH
OFFICIAL FAULT CODEE08
Siemens
Siemens // OFFICIAL DIAGNOSTIC BENCH

Siemens Dishwasher E08

DishwasherWater Level Pressure Switch & Air Dome
Premium built-in dishwasher with open illuminated stainless steel interior and precision spray arms
Dishwasher
Select Appliance Type
0ms Instant Telemetry Switch
BSH Group: Equivalent Code Across OEM Group Brands
BSH Electronic Architecture (Bosch / Siemens / Neff / Gaggenau)
BoschE08NeffE08GaggenauE08
Other Brands Sharing Code E08:SamsungE08LGE08BekoE08HaierE08CandyE08V-ZugE08HooverE08LiebherrE08

Symptom / Description

FAULT

Siemens iQ300 / iQ500 / iQ700 / iQ800 studioLine Zeolith & varioSpeed Plus: Low water level in sump during heating E08; heat pump detects insufficient water coverage over heating ring.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Siemens dishwashers: Excess foam from hand dishwashing soap, overturned bowl collecting rinse water, sluggish water intake, or clogged sump filter.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED
1Remove excessive foam with cold water rinse. Inspect microfilter in sump. Verify inlet flow rate (> 2.5 L/min). Ensure deep bowls face downwards. Press and hold Start button for 4 seconds until display indicates '0:01', wait for evacuation pump, then power off.
AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time
AI WORKSHOP PROTOCOL ENGINE
Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH
Need Help? Call a Certified TechnicianWorldwide Siemens Parts Finder
Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

SWISS ATELIER TECHNICAL BLUEPRINT // 2026 SCHEMATIC STANDARD

Hydraulic & Drainage Loop

Drain Pump M2, Impeller Chamber, Sump Filter & Analog Pressostat

CALIBRATED TEST POINTS (TP1 / TP2)
ACTIVE MULTIMETER BENCH
MAIN PCB CONTROLLER32-BIT MCUFIRMWARE v26.4SOLID-STATE RELAYTRIAC TY1 // 16A 600V230V AC MAINSLINE FILTER L-NJ1J2TP1TP2PRECISION BENCH METERAUTO-RANGE ΩCAT III168.4 ΩVΩCOMDRAIN PUMP M2DRAIN OUTFLOWRATED COIL: 150-280Ω
Target Component
Mechanical Pressure Switch Contacts / Inductive Frequency Sensor
Nominal Resistance / Test Range
Mechanical: Continuity 0.0Ω–0.2Ω (Empty: 11-12, Full: 11-14). Electronic: 20Ω–45Ω coil resistance.
Test Harness Pins
Across switch spade contacts with harness unplugged; electronic output: 40Hz–50Hz frequency signal
Diagnostic Verification Rule
Measure coil resistance unplugged. If OL (open loop) or < 50 Ω (shorted), replace pump assembly.
CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLWater Level Pressure Switch & Air DomeDishwasher
2. Multimeter & Electrical Bench Tests (Ω)
MODE: OHMMETER (Ω)AUTO-RANGE
Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board
CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)
Nominal Resistance (Ω)
Mechanical: Continuity 0.0Ω–0.2Ω (Empty: 11-12, Full: 11-14). Electronic: 20Ω–45Ω coil resistance.NOMINAL
0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)
▲ NOMINAL OPERATING WINDOW
Target Component:Mechanical Pressure Switch Contacts / Inductive Frequency Sensor
Test Pins & Connections
PROBE (+)
PROBE (-)
Across switch spade contacts with harness unplugged; electronic output: 40Hz–50Hz frequency signal
Tolerance & Diagnostic CriteriaMechanical switch contacts must transition cleanly on gentle breath pressure. Coil ~22Ω ±5%.
1. Pre-Intervention Electrical Safety Protocols
  • !Electrical Safety Protocol: Cut 230V mains power before accessing the upper chassis or pressure switch terminals.
  • !Drain appliance tub completely before disconnecting pressure switch sensing hoses.
  • !Never blow high-pressure compressed air into electronic analog pressure sensors: internal diaphragms will rupture!
3. Preliminary Mechanical & Visual Checks
  • Disconnect the silicone pressure tube from the lower air trap and inspect for soap sludge, lint, or water blockage.
  • Inspect the flexible rubber hose along its entire length for pinholes, cracks, or loose clamp fit.
  • Thoroughly flush the lower compression chamber (air dome) with hot water to dissolve detergent buildup.
Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Siemens E08

FAQ TREE
What does error code E08 mean on a Siemens appliance?

Siemens error code E08 indicates: Siemens iQ300 / iQ500 / iQ700 / iQ800 studioLine Zeolith & varioSpeed Plus: Low water level in sump during heating E08; heat pump detects insufficient water coverage over heating ring..

What is the root cause of Siemens error code E08?

The primary root cause for Siemens code E08 is: On Siemens dishwashers: Excess foam from hand dishwashing soap, overturned bowl collecting rinse water, sluggish water intake, or clogged sump filter..

How do I fix or resolve Siemens error code E08?

To resolve error code E08: Remove excessive foam with cold water rinse. Inspect microfilter in sump. Verify inlet flow rate (> 2.5 L/min). Ensure deep bowls face downwards. Press and hold Start button for 4 seconds until display indicates '0:01', wait for evacuation pump, then power off.

Is it safe to clear Siemens error code E08 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Siemens code E08 persists, the physical component causing On Siemens dishwashers: Excess foam from hand dishwashing soap, overturned bowl collecting rinse water, sluggish water intake, or clogged sump filter. must be inspected or replaced.

How do I test electrical resistance for Siemens code E08 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Mechanical Pressure Switch Contacts / Inductive Frequency Sensor across Across switch spade contacts with harness unplugged; electronic output: 40Hz–50Hz frequency signal. Expected nominal reading is Mechanical: Continuity 0.0Ω–0.2Ω (Empty: 11-12, Full: 11-14). Electronic: 20Ω–45Ω coil resistance.. Tolerance: Mechanical switch contacts must transition cleanly on gentle breath pressure. Coil ~22Ω ±5%..

What safety protocol must be followed before servicing Siemens code E08?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

What does Siemens error code E08 mean on a Dishwasher?

Siemens error code E08 on a Dishwasher indicates: Siemens iQ300 / iQ500 / iQ700 / iQ800 studioLine Zeolith & varioSpeed Plus: Low water level in sump during heating E08; heat pump detects insufficient water coverage over heating ring.. Primary cause: On Siemens dishwashers: Excess foam from hand dishwashing soap, overturned bowl collecting rinse water, sluggish water intake, or clogged sump filter.. Recommended solution: Remove excessive foam with cold water rinse. Inspect microfilter in sump. Verify inlet flow rate (> 2.5 L/min). Ensure deep bowls face downwards. Press and hold Start button for 4 seconds until display indicates '0:01', wait for evacuation pump, then power off..

What does Siemens error code E08 mean on a Tumble Dryer?

Siemens error code E08 on a Tumble Dryer indicates: Siemens iQ500 / iQ700 / iQ800 studioLine selfCleaning condenser & sensoFresh: Heat pump auxiliary relay / defrost fault E08; heat pump evaporator icing up or defrost cycle fails to initiate.. Primary cause: On Siemens tumble dryers: Defective defrost changeover valve solenoid, stuck auxiliary compressor relay, or low refrigerant charge causing freeze-up.. Recommended solution: Defrost machine completely. Measure defrost solenoid coil resistance (~2.0–2.5 kΩ). Inspect compressor auxiliary relays on control board. Turn selector from Off to 6 o'clock, hold Gentle/Delicates key, advance knob to position 7, release and return to Off..

Community Verification

COMMUNITY

Did this solution resolve the issue?

Siemens E08 — Multi-Appliance Technical Reference

Verified OEM diagnostic specifications across all appliance systems sharing this fault code.

Siemens E08 — Dishwasher

[ACTIVE]
Symptom / Description:

Siemens iQ300 / iQ500 / iQ700 / iQ800 studioLine Zeolith & varioSpeed Plus: Low water level in sump during heating E08; heat pump detects insufficient water coverage over heating ring.

Root Cause:

On Siemens dishwashers: Excess foam from hand dishwashing soap, overturned bowl collecting rinse water, sluggish water intake, or clogged sump filter.

Repair Instructions:

Remove excessive foam with cold water rinse. Inspect microfilter in sump. Verify inlet flow rate (> 2.5 L/min). Ensure deep bowls face downwards. Press and hold Start button for 4 seconds until display indicates '0:01', wait for evacuation pump, then power off.

Siemens E08 — Dryer

Symptom / Description:

Siemens iQ500 / iQ700 / iQ800 studioLine selfCleaning condenser & sensoFresh: Heat pump auxiliary relay / defrost fault E08; heat pump evaporator icing up or defrost cycle fails to initiate.

Root Cause:

On Siemens tumble dryers: Defective defrost changeover valve solenoid, stuck auxiliary compressor relay, or low refrigerant charge causing freeze-up.

Repair Instructions:

Defrost machine completely. Measure defrost solenoid coil resistance (~2.0–2.5 kΩ). Inspect compressor auxiliary relays on control board. Turn selector from Off to 6 o'clock, hold Gentle/Delicates key, advance knob to position 7, release and return to Off.

SEMANTIC KNOWLEDGE GRAPH // SIEMENS

Related Siemens Dishwasher Error Codes

Diagnostic Link Mesh14 OEM Cross-References

Cross-referenced diagnostic codes for technicians inspecting similar component subsystems.

E09Dishwasher
Drainage System & Drain Pump
Siemens iQ300 / iQ500 / iQ700 / iQ800 studioLine Zeolith & varioSpeed Plus: Heating circuit ...
Inspect Protocol
E10Dishwasher
Drainage System & Drain Pump
Siemens iQ300 / iQ500 / iQ700 / iQ800 studioLine Zeolith & varioSpeed Plus: Scale build-up o...
Inspect Protocol
E11Dishwasher
NTC Temperature Sensor & Thermistor
Siemens iQ300 / iQ500 / iQ700 / iQ800 studioLine Zeolith & varioSpeed Plus: NTC temperature ...
Inspect Protocol
E12Dishwasher
Drainage System & Drain Pump
Siemens iQ300 / iQ500 / iQ700 / iQ800 studioLine Zeolith & varioSpeed Plus: Severe lime scal...
Inspect Protocol
E13Dishwasher
NTC Temperature Sensor & Thermistor
Siemens iQ300 / iQ500 / iQ700 / iQ800 studioLine Zeolith & varioSpeed Plus: High water inlet...
Inspect Protocol
E14Dishwasher
Drainage System & Drain Pump
Siemens iQ300 / iQ500 / iQ700 / iQ800 studioLine Zeolith & varioSpeed Plus: Flowmeter turbin...
Inspect Protocol
E15Dishwasher
Water Level Pressure Switch & Air Dome
Siemens iQ300 / iQ500 / iQ700 / iQ800 studioLine Zeolith & varioSpeed Plus: AquaStop safety ...
Inspect Protocol
E16Dishwasher
Drainage System & Drain Pump
Siemens iQ300 / iQ500 / iQ700 / iQ800 studioLine Zeolith & varioSpeed Plus: Uncontrolled wat...
Inspect Protocol
E17Dishwasher
Drainage System & Drain Pump
Siemens iQ300 / iQ500 / iQ700 / iQ800 studioLine Zeolith & varioSpeed Plus: High water inlet...
Inspect Protocol
E18Dishwasher
Drainage System & Drain Pump
Siemens iQ300 / iQ500 / iQ700 / iQ800 studioLine Zeolith & varioSpeed Plus: Low water flow i...
Inspect Protocol
E19Dishwasher
Drainage System & Drain Pump
Siemens iQ300 / iQ500 / iQ700 / iQ800 studioLine Zeolith & varioSpeed Plus: Dispenser actuat...
Inspect Protocol
E20Dishwasher
Drainage System & Drain Pump
Siemens iQ300 / iQ500 / iQ700 / iQ800 studioLine Zeolith & varioSpeed Plus: Circulation pump...
Inspect Protocol
E21Dishwasher
Drainage System & Drain Pump
Siemens iQ300 / iQ500 / iQ700 / iQ800 studioLine Zeolith & varioSpeed Plus: Circulation pump...
Inspect Protocol
E22Dishwasher
Drainage System & Drain Pump
Siemens iQ300 / iQ500 / iQ700 / iQ800 studioLine Zeolith & varioSpeed Plus: Sump filter bloc...
Inspect Protocol
CodesErreur.com

Premium appliance diagnostics & repair database.
Powered by AI to help certified technicians worldwide.

Trusted by professionals in CH & FR

Platform

Search DatabasePRO Diagnostic AIPRODiagnostic ToolsBrands

Workshop Tools

Brands (87)OEM ManualsFind Rating PlateParts Locator

For Technicians

SpecialistsTechnician ForumTech JobsPremium

Corporate

Terms of ServicePrivacy PolicyOfficial Swiss Repair Partner: Electroassistance
OPERATIONAL SAFETY SPECIFICATION

SAFETY DISCLAIMER

The technical information, diagnostic guides, error codes, and AI-generated suggestions provided on this website are intended exclusively for certified and qualified professionals. Appliance repair involves severe electrical hazards, high voltages, and mechanical risks that can result in fatal injury or severe property damage. If you are not a trained technician, do not attempt to repair any appliances. CodesErreur assumes no responsibility or liability for any damage, injury, or consequential losses resulting from the use of the information provided on this platform. You use all information entirely at your own risk.

© 2026 CodesErreur. All rights reserved.

Terms of Service Privacy Policy