Electrolux Error Codes & Diagnostics

Error code E74 is displayed, and the drying cycle stops or fails to start.

Info: The drying NTC temperature sensor is detected by the control board as being in the wrong position or dislodged from its housing.

Auto-dry circuit malfunction.

Check moisture sensor bars for residue. PRO TIP: 'Flow Sense' or restricted airflow errors mean you must clean the vent — this is the #1 fire hazard.

Appliance stops mid-cycle, humming noise.

Info: The circulation pump is blocked or jammed.

An alarm (indicated by 'Alerte relative au bac d’eau de condensation') is automatically displayed at the end of each cycle (if not manually disabled).

Info: The condensation water tank is full.

A warning alert is displayed regarding the condenser (as indicated by 'Alerte relative au nettoyage du condenseur').

Info: The condenser needs cleaning.

Appliance is not filling with water.

Info: Water inlet fault, similar to i10. Can be a faulty water valve.

Oven door lock does not engage or disengage correctly.

Info: Fault with the door lock sensor or the lock mechanism itself.

Machine stops working, leak detected.

Info: Leak detected and anti-flood device activated. Similar to i30.

Machine stops mid-cycle, often during spin.

Info: An imbalance in the drum has been detected by the motor sensor.

Lights are on, but the refrigerator is not cooling.

Info: The appliance is in 'Demo' or 'Shop' mode.

Water has been detected in the base of the machine.

Info: Internal leak has activated the Aqua Control or flood protection switch.

Appliance will not start or has no power.

Info: Power supply problem. The voltage or frequency is outside of the appliance's normal operating range.

Appliance is dead or has intermittent power.

Info: Incompatibility between the main electronic control board and the safety relay.

The screen displays "Err" and the Start/Pause indicator light flashes.

Info: The appliance door (hublot) is open during a cycle or when attempting to start a cycle.

For user interfaces of TC2, TC3, and TC4 levels, a blinking 'Err' text appears in the program duration display. For TC1 level user interfaces, the message 'Not possible' appears in the text line. The buzzer does not sound a melody, and the Start/Pause button LED does not flash. These signals are displayed for approximately 1 second.

Info: An option button incompatible with the selected program was pressed, OR an option button was pressed or the selector knob was turned during a program cycle.

Hob switches off during use.

Info: The electronics are overheating, possibly due to a faulty cooling fan or blocked ventilation.

Hob does not work or displays error immediately.

Info: The mains voltage supply is outside the acceptable range (either too high or too low).

Water leakage detected, machine stops.

Info: Severe leak detected by the Aqua Control system, often due to a burst hose or major component failure.

One or more cooking zones are not working.

Info: Communication failure between the user interface and the power board for a specific zone.

Hob is completely unresponsive.

Info: Communication failure between the two power modules (in larger hobs) or between control and power boards.

Hob shows error code and does not operate.

Info: Configuration error in the control board electronics.

Water is not entering the appliance.

Info: Water tap is closed, inlet hose is kinked or blocked, or water inlet valve filter is blocked.

No water entering the appliance during wash cycle.

Info: Problem with solenoid valve or wiring to the valve.

Appliance is not draining water.

Info: The drain filter is clogged, drain pump is blocked, or the drain hose is kinked or blocked.

Difficulty draining water, especially during spin cycle.

Info: Faulty drain pump or problem with the pump's wiring or control board connection.

Washing machine overfills with water.

Info: Faulty analogue pressure sensor. It's not correctly detecting the water level.

The door will not lock, or the cycle will not start.

Info: Faulty door lock mechanism, wiring issue, or the door is not closed properly.

Drum does not turn or spins erratically.

Info: Faulty signal from the tacho generator on the motor, indicating an issue with motor speed sensing.

Clothes are not drying, no heat.

Info: General heating fault. Could be the heating element, thermostat, or related wiring.

Water does not heat up during the wash cycle.

Info: Heating circuit fault. The heating element has failed or there is insufficient heating during the wash.