Access our premium database of error codes, common faults, and professional repair solutions for Baumatic appliances.
Freezer high temperature alarm
The temperature in the freezer is too high. This could be from the door being left open, a power cut, or a system fault.
Check that the door is fully closed and the seal is intact. Avoid opening the door to allow it to cool. If it doesn't resolve, there may be a cooling system issue.
Refrigerator high temperature alarm
The temperature in the fridge is too high. Caused by a door left ajar, blocked air vents, or a cooling fault.
Ensure the door is closed and that food items are not blocking the air circulation vents inside.
Baumatic E01: Door lock safety interlock fault in Washing Machine; door switch contact fails to close or open.
The washing machine door is not closed properly, or the door lock mechanism has failed.
Ensure the door is firmly shut. Check for obstructions. If the problem persists, the door interlock may need replacement.
Baumatic E1: Water/air heating failure in Hob / Cooktop; heating circuit does not reach set temperature.
The internal electronics of the hob are too hot. This is usually caused by blocked ventilation or a failed cooling fan.
Turn off the hob and ensure the ventilation slots underneath are not blocked. Allow it to cool. If the fan is not working, it needs repair.
Baumatic E02: Water inlet / filling timeout in Washing Machine; appliance fails to fill to minimum operational level.
The machine has failed to fill with water in the allotted time. The water tap may be off, the hose kinked, or the inlet valve faulty.
Check that the water supply is turned on and the inlet hose is not bent. Clean the filter in the inlet valve.
Cooking zone sensor overheat
The surface temperature sensor for a cooking zone is too hot, often from an empty pan being left on high heat.
Remove the cookware from the zone and turn it off. Allow the hob surface to cool down completely.
Baumatic E03: Water drainage failure detected in Washing Machine; drain pump cannot evacuate water within safety time limit.
The machine has failed to drain water within the set time. The drain filter is likely blocked, or the drain hose is obstructed.
Open the small door at the bottom front of the machine. Unscrew the filter, clean it thoroughly, and check the pump impeller.
Baumatic E3: Operational cycle fault detected during Hob / Cooktop program execution.
The hob has detected that the incoming power supply voltage is too high or too low for safe operation.
This is an issue with the home's electrical supply. Consult an electrician to check the voltage at the outlet.
Overfill or anti-flood error
Too much water has entered the drum, often due to a faulty pressure switch or a stuck water inlet valve.
Turn off the machine and the water supply. Check the pressure switch hose for blockages. May require a new inlet valve.
Overfilling / Leak detected
The machine has detected too much water in the tub or a leak in the base, activating the anti-flood switch.
Turn off the water supply immediately. Carefully tilt the machine to drain water from the base. Find and repair the source of the leak.
Temperature sensor (NTC) error
The temperature sensor is providing an incorrect reading, is open circuit, or short-circuited.
This error typically requires an engineer to test the NTC sensor with a multimeter and replace it if faulty.
Baumatic E06: Motor drive or inverter rotation anomaly in Washing Machine; drum/motor fails to spin at target RPM.
An issue with the main drive motor has been detected. This could be worn carbon brushes, a wiring issue, or a motor failure.
Check and replace motor carbon brushes if they are worn down. Check all motor connections. If the problem persists, the motor may need replacement.
No pan detected / Unsuitable pan
There is no pan on the cooking zone, the pan is not induction-compatible (not magnetic), or it is too small or off-center.
Place a suitable, magnetic-bottom pan in the center of the cooking zone.
Motor jammed or door lock overheat
This code can indicate either a jammed motor that is unable to turn, or an issue with the door lock overheating.
Check if the drum can be turned by hand (when empty). Inspect the door lock wiring and mechanism. This may need professional diagnosis.
Baumatic E7: NTC temperature sensor signal out of range (open or short circuit) in Dishwasher.
The machine has detected a dangerously high temperature, often due to a faulty NTC or a stuck heating element relay.
Disconnect the appliance from power. This is a critical safety issue and requires a qualified technician to diagnose and repair.
Baumatic E08: Motor drive or inverter rotation anomaly in Washing Machine; drum/motor fails to spin at target RPM.
The tacho coil, which measures the motor's speed, is faulty or has a bad connection.
Check the wiring and small tacho coil on the end of the motor. The entire motor may need to be replaced if the tacho is not a separate part.
Cooling fan air intake blocked
The air inlet for the internal cooling fan is obstructed, preventing proper airflow.
Check underneath the hob and ensure there are no objects, dust, or debris blocking the air vents.
Software configuration / Touchpad error
A button on the control panel is stuck, or there is a software mismatch/corruption on the main board.
Try cleaning the control panel. Perform a power reset. If the error persists, the control panel or main board may need replacement.
Drum sensor or drive motor fault
The control board is not receiving a signal from the drum position sensor or has detected a major motor fault.
This is a complex fault requiring an engineer to diagnose the specific component (motor, sensor, or control board).
Baumatic E11: NTC temperature sensor signal out of range (open or short circuit) in Washer Dryer.
On a washer-dryer, the temperature sensor for the drying circuit has failed.
The dryer NTC sensor needs to be located, tested, and likely replaced by a service technician.
Communication error between boards
The main control board and the display board cannot communicate with each other due to a wiring or component fault.
Check the wiring harness connecting the control modules. This fault often requires replacement of one of the circuit boards.
Drain pump blockage detected
A significant blockage in the drain filter or pump is preventing water from being expelled effectively.
Perform a thorough clean of the drain pump filter and check that the pump impeller can spin freely.
Door lock mechanism failure
Indicates a definitive failure of the door lock, different from a 'door open' signal.
The door lock assembly needs to be replaced.
No heating during wash cycle
The machine has detected that the water is not heating up. The heating element or its wiring is likely faulty.
Requires an engineer to test the heating element, thermostat, and wiring connections to the main control board.
Stuck button or key on control panel
A button on the oven's control panel has been pressed for too long or is physically stuck.
Wipe the control panel clean and press the indicated button to try and release it. If it's a touch panel, a power reset may help.
Persistent fault / Flashing symbol
A continuous flashing 'F' or other symbol often indicates a sensor failure or a more serious internal electronic fault.
Try resetting the hob by turning off the power at the breaker for 10 minutes. If the fault persists, it requires a technician.
Baumatic F01: NTC temperature sensor signal out of range (open or short circuit) in Oven / Microwave.
The oven's temperature sensor (thermistor) is open or short-circuited.
Disconnect power to the oven. Test the sensor for resistance. If faulty, replace the sensor.
Baumatic F1: NTC temperature sensor signal out of range (open or short circuit) in Refrigerator / Freezer.
The temperature sensor (NTC) inside the freezer compartment has failed.
The freezer NTC sensor needs to be tested and replaced by a qualified technician.
Baumatic F02: Operational cycle fault detected during Oven / Microwave program execution.
The cooling fan is not working, ventilation is blocked, or the temperature control relay is stuck on.
Ensure oven ventilation is not obstructed. Check if the cooling fan operates. If the issue persists, the main control board may need repair.
Refrigerator sensor fault
The temperature sensor (NTC) inside the fresh food (refrigerator) compartment has failed.
The refrigerator NTC sensor needs to be tested and replaced by a qualified technician.
Our official certified partners service Baumatic appliances in your area.