OEM VERIFIED BENCH

OFFICIAL FAULT CODEAL5

AEG // OFFICIAL DIAGNOSTIC BENCH

AEG AL5

DishwasherWater Level Pressure Switch & Air Dome

Dishwasher

Other Brands Sharing Code AL5:ElectroluxAL5 ZanussiAL5 Arthur MartinAL5 CastorAL5 FaureAL5 ZoppasAL5

Symptom / Description

FAULT

AEG Favorit / ProClean / ComfortLift Series: Water fill failure AL5 (legacy EDW1500 alphanumeric); inlet valve open but required water level not reached.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On AEG (AEG Favorit / ProClean / ComfortLift Series) models: Closed supply tap, blocked inlet filter, defective 230V solenoid valve coil (nominal 3.8–4.4 kΩ), or airlock in water softener matrix.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Verify tap water pressure. Clean mesh filter in inlet fitting. Measure solenoid coil resistance (expected 3.8–4.4 kΩ). Rotate selector to 12 o'clock (OFF), press and hold Start/Pause and Exit simultaneously for 4 seconds until the diagnostic LED sequence resets error memory.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide AEG Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLWater Level Pressure Switch & Air DomeDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

Mechanical: Continuity 0.0Ω–0.2Ω (Empty: 11-12, Full: 11-14). Electronic: 20Ω–45Ω coil resistance.NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Mechanical Pressure Switch Contacts / Inductive Frequency Sensor

Test Pins & Connections

PROBE (+)

PROBE (-)

Across switch spade contacts with harness unplugged; electronic output: 40Hz–50Hz frequency signal

Tolerance & Diagnostic CriteriaMechanical switch contacts must transition cleanly on gentle breath pressure. Coil ~22Ω ±5%.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Cut 230V mains power before accessing the upper chassis or pressure switch terminals.
!Drain appliance tub completely before disconnecting pressure switch sensing hoses.
!Never blow high-pressure compressed air into electronic analog pressure sensors: internal diaphragms will rupture!

3. Preliminary Mechanical & Visual Checks

Disconnect the silicone pressure tube from the lower air trap and inspect for soap sludge, lint, or water blockage.
Inspect the flexible rubber hose along its entire length for pinholes, cracks, or loose clamp fit.
Thoroughly flush the lower compression chamber (air dome) with hot water to dissolve detergent buildup.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: AEG AL5

FAQ TREE

What does error code AL5 mean on a AEG appliance?

AEG error code AL5 indicates: AEG Favorit / ProClean / ComfortLift Series: Water fill failure AL5 (legacy EDW1500 alphanumeric); inlet valve open but required water level not reached..

What is the root cause of AEG error code AL5?

The primary root cause for AEG code AL5 is: On AEG (AEG Favorit / ProClean / ComfortLift Series) models: Closed supply tap, blocked inlet filter, defective 230V solenoid valve coil (nominal 3.8–4.4 kΩ), or airlock in water softener matrix..

How do I fix or resolve AEG error code AL5?

To resolve error code AL5: Verify tap water pressure. Clean mesh filter in inlet fitting. Measure solenoid coil resistance (expected 3.8–4.4 kΩ). Rotate selector to 12 o'clock (OFF), press and hold Start/Pause and Exit simultaneously for 4 seconds until the diagnostic LED sequence resets error memory.

Is it safe to clear AEG error code AL5 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if AEG code AL5 persists, the physical component causing On AEG (AEG Favorit / ProClean / ComfortLift Series) models: Closed supply tap, blocked inlet filter, defective 230V solenoid valve coil (nominal 3.8–4.4 kΩ), or airlock in water softener matrix. must be inspected or replaced.

How do I test electrical resistance for AEG code AL5 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Mechanical Pressure Switch Contacts / Inductive Frequency Sensor across Across switch spade contacts with harness unplugged; electronic output: 40Hz–50Hz frequency signal. Expected nominal reading is Mechanical: Continuity 0.0Ω–0.2Ω (Empty: 11-12, Full: 11-14). Electronic: 20Ω–45Ω coil resistance.. Tolerance: Mechanical switch contacts must transition cleanly on gentle breath pressure. Coil ~22Ω ±5%..

What safety protocol must be followed before servicing AEG code AL5?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEAL5

AEG // OFFICIAL DIAGNOSTIC BENCH

AEG AL5

DishwasherWater Level Pressure Switch & Air Dome

Dishwasher

Other Brands Sharing Code AL5:ElectroluxAL5 ZanussiAL5 Arthur MartinAL5 CastorAL5 FaureAL5 ZoppasAL5

Symptom / Description

FAULT

AEG Favorit / ProClean / ComfortLift Series: Water fill failure AL5 (legacy EDW1500 alphanumeric); inlet valve open but required water level not reached.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On AEG (AEG Favorit / ProClean / ComfortLift Series) models: Closed supply tap, blocked inlet filter, defective 230V solenoid valve coil (nominal 3.8–4.4 kΩ), or airlock in water softener matrix.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide AEG Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLWater Level Pressure Switch & Air DomeDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

Mechanical: Continuity 0.0Ω–0.2Ω (Empty: 11-12, Full: 11-14). Electronic: 20Ω–45Ω coil resistance.NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Mechanical Pressure Switch Contacts / Inductive Frequency Sensor

Test Pins & Connections

PROBE (+)

PROBE (-)

Across switch spade contacts with harness unplugged; electronic output: 40Hz–50Hz frequency signal

Tolerance & Diagnostic CriteriaMechanical switch contacts must transition cleanly on gentle breath pressure. Coil ~22Ω ±5%.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Cut 230V mains power before accessing the upper chassis or pressure switch terminals.
!Drain appliance tub completely before disconnecting pressure switch sensing hoses.
!Never blow high-pressure compressed air into electronic analog pressure sensors: internal diaphragms will rupture!

3. Preliminary Mechanical & Visual Checks

Disconnect the silicone pressure tube from the lower air trap and inspect for soap sludge, lint, or water blockage.
Inspect the flexible rubber hose along its entire length for pinholes, cracks, or loose clamp fit.
Thoroughly flush the lower compression chamber (air dome) with hot water to dissolve detergent buildup.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: AEG AL5

FAQ TREE

What does error code AL5 mean on a AEG appliance?

AEG error code AL5 indicates: AEG Favorit / ProClean / ComfortLift Series: Water fill failure AL5 (legacy EDW1500 alphanumeric); inlet valve open but required water level not reached..

What is the root cause of AEG error code AL5?

How do I fix or resolve AEG error code AL5?

Is it safe to clear AEG error code AL5 by resetting power?

How do I test electrical resistance for AEG code AL5 using a multimeter?

What safety protocol must be followed before servicing AEG code AL5?

Community Verification

COMMUNITY

Did this solution resolve the issue?

AEG AL5

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: AEG AL5

Community Verification

Related AEG Dishwasher Error Codes

AEG AL5

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: AEG AL5

Community Verification

Related AEG Dishwasher Error Codes