OEM VERIFIED BENCH

OFFICIAL FAULT CODEEH2

AEG // OFFICIAL DIAGNOSTIC BENCH

AEG EH2

Q: What does error code EH2 mean on a AEG appliance?

AEG error code EH2 indicates: AEG Lavamat / ProSteam 7000/8000/9000 Series: Mains supply overvoltage alarm EH2; mains electrical supply exceeds 275V RMS..

Q: What is the root cause of AEG error code EH2?

The primary root cause for AEG code EH2 is: On AEG (AEG Lavamat / ProSteam 7000/8000/9000 Series) models: Lightning strike on local grid, loss of neutral in three-phase building distribution causing 400V phase shift, or transient power surges..

Q: How do I fix or resolve AEG error code EH2?

To resolve error code EH2: Unplug washing machine immediately to prevent board destruction. Have an electrician test mains voltage (must not exceed 253V AC maximum). Rotate selector to 12 o'clock (OFF), press and hold Start/Pause and Exit simultaneously for 4 seconds until the diagnostic LED sequence resets error memory.

Q: Is it safe to clear AEG error code EH2 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if AEG code EH2 persists, the physical component causing On AEG (AEG Lavamat / ProSteam 7000/8000/9000 Series) models: Lightning strike on local grid, loss of neutral in three-phase building distribution causing 400V phase shift, or transient power surges. must be inspected or replaced.

Q: How do I test electrical resistance for AEG code EH2 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test PCB Power Supply Rails & DC Bus Filter Capacitors across Across SMPS output electrolytic capacitors on low-voltage side (test bench verification). Expected nominal reading is Low-voltage rails: +5.0V DC (Logic), +12.0V DC (Relays), +3.3V DC (MCU). Relay coils: 200Ω–450Ω.. Tolerance: DC rail ripple must remain <50mV. Direct continuity (0Ω) across DC bus rails indicates dead short..

Q: What safety protocol must be followed before servicing AEG code EH2?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Washing MachineElectronic Control Board (PCB) & Bus Communications

Washing Machine

Other Brands Sharing Code EH2:ElectroluxEH2 ZanussiEH2 Arthur MartinEH2 CastorEH2 FaureEH2 ZoppasEH2

Symptom / Description

FAULT

AEG Lavamat / ProSteam 7000/8000/9000 Series: Mains supply overvoltage alarm EH2; mains electrical supply exceeds 275V RMS.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On AEG (AEG Lavamat / ProSteam 7000/8000/9000 Series) models: Lightning strike on local grid, loss of neutral in three-phase building distribution causing 400V phase shift, or transient power surges.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Unplug washing machine immediately to prevent board destruction. Have an electrician test mains voltage (must not exceed 253V AC maximum). Rotate selector to 12 o'clock (OFF), press and hold Start/Pause and Exit simultaneously for 4 seconds until the diagnostic LED sequence resets error memory.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide AEG Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLElectronic Control Board (PCB) & Bus CommunicationsWashing Machine

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

Low-voltage rails: +5.0V DC (Logic), +12.0V DC (Relays), +3.3V DC (MCU). Relay coils: 200Ω–450Ω.NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:PCB Power Supply Rails & DC Bus Filter Capacitors

Test Pins & Connections

PROBE (+)

PROBE (-)

Across SMPS output electrolytic capacitors on low-voltage side (test bench verification)

Tolerance & Diagnostic CriteriaDC rail ripple must remain <50mV. Direct continuity (0Ω) across DC bus rails indicates dead short.

1. Pre-Intervention Electrical Safety Protocols

!High-Voltage Safety Protocol: Disconnect 230V power before unplugging edge connectors or removing PCB.
!High Voltage DC Warning: Wait at least 5 minutes for SMPS and inverter filter capacitors (up to 380V DC) to discharge safely.
!Electrostatic Discharge (ESD): Ground yourself to the metal chassis or wear an antistatic wrist strap before touching circuit tracks.

3. Preliminary Mechanical & Visual Checks

Inspect PCB tracks with a magnifying glass for blown triacs, darkened copper tracks, or cold solder joints on power relays.
Check electrolytic capacitors for bulging tops or leaked electrolyte residue around pins.
Verify edge connector locking clips are intact and pins are free of vibration fretting corrosion.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: AEG EH2

FAQ TREE

What does error code EH2 mean on a AEG appliance?

AEG error code EH2 indicates: AEG Lavamat / ProSteam 7000/8000/9000 Series: Mains supply overvoltage alarm EH2; mains electrical supply exceeds 275V RMS..

What is the root cause of AEG error code EH2?

The primary root cause for AEG code EH2 is: On AEG (AEG Lavamat / ProSteam 7000/8000/9000 Series) models: Lightning strike on local grid, loss of neutral in three-phase building distribution causing 400V phase shift, or transient power surges..

How do I fix or resolve AEG error code EH2?

To resolve error code EH2: Unplug washing machine immediately to prevent board destruction. Have an electrician test mains voltage (must not exceed 253V AC maximum). Rotate selector to 12 o'clock (OFF), press and hold Start/Pause and Exit simultaneously for 4 seconds until the diagnostic LED sequence resets error memory.

Is it safe to clear AEG error code EH2 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if AEG code EH2 persists, the physical component causing On AEG (AEG Lavamat / ProSteam 7000/8000/9000 Series) models: Lightning strike on local grid, loss of neutral in three-phase building distribution causing 400V phase shift, or transient power surges. must be inspected or replaced.

How do I test electrical resistance for AEG code EH2 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test PCB Power Supply Rails & DC Bus Filter Capacitors across Across SMPS output electrolytic capacitors on low-voltage side (test bench verification). Expected nominal reading is Low-voltage rails: +5.0V DC (Logic), +12.0V DC (Relays), +3.3V DC (MCU). Relay coils: 200Ω–450Ω.. Tolerance: DC rail ripple must remain <50mV. Direct continuity (0Ω) across DC bus rails indicates dead short..

What safety protocol must be followed before servicing AEG code EH2?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEEH2

AEG // OFFICIAL DIAGNOSTIC BENCH

AEG EH2

Washing MachineElectronic Control Board (PCB) & Bus Communications

Washing Machine

Other Brands Sharing Code EH2:ElectroluxEH2 ZanussiEH2 Arthur MartinEH2 CastorEH2 FaureEH2 ZoppasEH2

Symptom / Description

FAULT

AEG Lavamat / ProSteam 7000/8000/9000 Series: Mains supply overvoltage alarm EH2; mains electrical supply exceeds 275V RMS.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On AEG (AEG Lavamat / ProSteam 7000/8000/9000 Series) models: Lightning strike on local grid, loss of neutral in three-phase building distribution causing 400V phase shift, or transient power surges.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide AEG Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLElectronic Control Board (PCB) & Bus CommunicationsWashing Machine

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

Low-voltage rails: +5.0V DC (Logic), +12.0V DC (Relays), +3.3V DC (MCU). Relay coils: 200Ω–450Ω.NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:PCB Power Supply Rails & DC Bus Filter Capacitors

Test Pins & Connections

PROBE (+)

PROBE (-)

Across SMPS output electrolytic capacitors on low-voltage side (test bench verification)

Tolerance & Diagnostic CriteriaDC rail ripple must remain <50mV. Direct continuity (0Ω) across DC bus rails indicates dead short.

1. Pre-Intervention Electrical Safety Protocols

!High-Voltage Safety Protocol: Disconnect 230V power before unplugging edge connectors or removing PCB.
!High Voltage DC Warning: Wait at least 5 minutes for SMPS and inverter filter capacitors (up to 380V DC) to discharge safely.
!Electrostatic Discharge (ESD): Ground yourself to the metal chassis or wear an antistatic wrist strap before touching circuit tracks.

3. Preliminary Mechanical & Visual Checks

Inspect PCB tracks with a magnifying glass for blown triacs, darkened copper tracks, or cold solder joints on power relays.
Check electrolytic capacitors for bulging tops or leaked electrolyte residue around pins.
Verify edge connector locking clips are intact and pins are free of vibration fretting corrosion.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: AEG EH2

FAQ TREE

What does error code EH2 mean on a AEG appliance?

AEG error code EH2 indicates: AEG Lavamat / ProSteam 7000/8000/9000 Series: Mains supply overvoltage alarm EH2; mains electrical supply exceeds 275V RMS..

What is the root cause of AEG error code EH2?

How do I fix or resolve AEG error code EH2?

Is it safe to clear AEG error code EH2 by resetting power?

How do I test electrical resistance for AEG code EH2 using a multimeter?

What safety protocol must be followed before servicing AEG code EH2?

Community Verification

COMMUNITY

Did this solution resolve the issue?

AEG EH2

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: AEG EH2

Community Verification

Related AEG Washing Machine Error Codes

AEG EH2

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: AEG EH2

Community Verification

Related AEG Washing Machine Error Codes