OEM VERIFIED BENCH

OFFICIAL FAULT CODEiD0

AEG // OFFICIAL DIAGNOSTIC BENCH

AEG iD0

DishwasherDrive Motor, Inverter & Tachometer Sensor

Dishwasher

Other Brands Sharing Code iD0:ElectroluxID0 ZanussiID0 Arthur MartinID0 CastorID0 FaureID0 ZoppasID0

Symptom / Description

FAULT

AEG Favorit / ProClean / ComfortLift Series: Tachometer signal missing from variable speed wash motor iD0; inverter fails to verify motor rotation.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On AEG (AEG Favorit / ProClean / ComfortLift Series) models: Tachometer pickup coil open circuit (nominal 110–135 Ω on inverter motor), detached sensor magnet, or broken connector lead.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Measure tachometer resistance across motor pins 4 and 5 (nominal 110–135 Ω). Verify wiring continuity back to inverter board. Rotate selector to 12 o'clock (OFF), press and hold Start/Pause and Exit simultaneously for 4 seconds until the diagnostic LED sequence resets error memory.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide AEG Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrive Motor, Inverter & Tachometer SensorDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

3Ω–6Ω (BLDC phase U-V-W) / 60Ω–180Ω (Tacho coil) / 1.5Ω–3.5Ω (Universal stator)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:3-Phase Motor Windings / Tacho Generator / Carbon Brushes

Test Pins & Connections

PROBE (+)

PROBE (-)

Across phase pins U-V, V-W, U-W on motor harness; across tacho pins

Tolerance & Diagnostic CriteriaBLDC phase winding values must be strictly balanced within ±0.3Ω. Hand rotation generates 1V–4V AC on tacho.

1. Pre-Intervention Electrical Safety Protocols

!High-Voltage Safety Protocol & DC Bus: Wait at least 5 minutes after power cutoff to allow inverter DC bus capacitors (380V DC) to bleed down.
!Verify 0V DC across inverter filter capacitors before unplugging motor harness connectors.
!Keep hands clear of drive belt and pulleys during any manual rotation tng.

3. Preliminary Mechanical & Visual Checks

Slip off drive belt and spin drum/motor shaft by hand to check for roaring or seized ball bearings.
For universal motors: verify carbon brushes have at least 10mm remaining length and smooth contact faces.
Inspect motor suspension rubber mounts and drive belt tension/groove profile.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: AEG ID0

FAQ TREE

What does error code ID0 mean on a AEG appliance?

AEG error code ID0 indicates: AEG Favorit / ProClean / ComfortLift Series: Tachometer signal missing from variable speed wash motor iD0; inverter fails to verify motor rotation..

What is the root cause of AEG error code ID0?

The primary root cause for AEG code ID0 is: On AEG (AEG Favorit / ProClean / ComfortLift Series) models: Tachometer pickup coil open circuit (nominal 110–135 Ω on inverter motor), detached sensor magnet, or broken connector lead..

How do I fix or resolve AEG error code ID0?

To resolve error code ID0: Measure tachometer resistance across motor pins 4 and 5 (nominal 110–135 Ω). Verify wiring continuity back to inverter board. Rotate selector to 12 o'clock (OFF), press and hold Start/Pause and Exit simultaneously for 4 seconds until the diagnostic LED sequence resets error memory.

Is it safe to clear AEG error code ID0 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if AEG code ID0 persists, the physical component causing On AEG (AEG Favorit / ProClean / ComfortLift Series) models: Tachometer pickup coil open circuit (nominal 110–135 Ω on inverter motor), detached sensor magnet, or broken connector lead. must be inspected or replaced.

How do I test electrical resistance for AEG code ID0 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test 3-Phase Motor Windings / Tacho Generator / Carbon Brushes across Across phase pins U-V, V-W, U-W on motor harness; across tacho pins. Expected nominal reading is 3Ω–6Ω (BLDC phase U-V-W) / 60Ω–180Ω (Tacho coil) / 1.5Ω–3.5Ω (Universal stator). Tolerance: BLDC phase winding values must be strictly balanced within ±0.3Ω. Hand rotation generates 1V–4V AC on tacho..

What safety protocol must be followed before servicing AEG code ID0?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEiD0

AEG // OFFICIAL DIAGNOSTIC BENCH

AEG iD0

DishwasherDrive Motor, Inverter & Tachometer Sensor

Dishwasher

Other Brands Sharing Code iD0:ElectroluxID0 ZanussiID0 Arthur MartinID0 CastorID0 FaureID0 ZoppasID0

Symptom / Description

FAULT

AEG Favorit / ProClean / ComfortLift Series: Tachometer signal missing from variable speed wash motor iD0; inverter fails to verify motor rotation.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On AEG (AEG Favorit / ProClean / ComfortLift Series) models: Tachometer pickup coil open circuit (nominal 110–135 Ω on inverter motor), detached sensor magnet, or broken connector lead.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide AEG Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrive Motor, Inverter & Tachometer SensorDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

3Ω–6Ω (BLDC phase U-V-W) / 60Ω–180Ω (Tacho coil) / 1.5Ω–3.5Ω (Universal stator)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:3-Phase Motor Windings / Tacho Generator / Carbon Brushes

Test Pins & Connections

PROBE (+)

PROBE (-)

Across phase pins U-V, V-W, U-W on motor harness; across tacho pins

Tolerance & Diagnostic CriteriaBLDC phase winding values must be strictly balanced within ±0.3Ω. Hand rotation generates 1V–4V AC on tacho.

1. Pre-Intervention Electrical Safety Protocols

!High-Voltage Safety Protocol & DC Bus: Wait at least 5 minutes after power cutoff to allow inverter DC bus capacitors (380V DC) to bleed down.
!Verify 0V DC across inverter filter capacitors before unplugging motor harness connectors.
!Keep hands clear of drive belt and pulleys during any manual rotation tng.

3. Preliminary Mechanical & Visual Checks

Slip off drive belt and spin drum/motor shaft by hand to check for roaring or seized ball bearings.
For universal motors: verify carbon brushes have at least 10mm remaining length and smooth contact faces.
Inspect motor suspension rubber mounts and drive belt tension/groove profile.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: AEG ID0

FAQ TREE

What does error code ID0 mean on a AEG appliance?

AEG error code ID0 indicates: AEG Favorit / ProClean / ComfortLift Series: Tachometer signal missing from variable speed wash motor iD0; inverter fails to verify motor rotation..

What is the root cause of AEG error code ID0?

How do I fix or resolve AEG error code ID0?

Is it safe to clear AEG error code ID0 by resetting power?

How do I test electrical resistance for AEG code ID0 using a multimeter?

What safety protocol must be followed before servicing AEG code ID0?

Community Verification

COMMUNITY

Did this solution resolve the issue?

AEG iD0

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: AEG ID0

Community Verification

Related AEG Dishwasher Error Codes

AEG iD0

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: AEG ID0

Community Verification

Related AEG Dishwasher Error Codes