OEM VERIFIED BENCH

OFFICIAL FAULT CODEFB

Ariston // OFFICIAL DIAGNOSTIC BENCH

Ariston FB

DishwasherDrainage System & Drain Pump

Dishwasher

Other Brands Sharing Code FB:WhirlpoolFB IndesitFB BauknechtFB PhilipsFB HotpointFB IgnisFB

Symptom / Description

FAULT

Ariston Hotpoint-Ariston 3D Zone Wash MaxiSpace Dishwasher: Motorized Diverter Valve (MDV) microswitch failure FB; cam switch does not pulse during diverter disc positioning.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Ariston dishwashers: Broken nylon gear teeth in MDV actuator, burnt drive motor winding, or oxidized internal microswitch wiper contacts.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Measure MDV synchronous drive motor resistance (6.0–7.5 kΩ). Check microswitch continuity with manual gear rotation (must switch between 0 Ω and infinite). Replace MDV. Hold Start/Reset key for 5 seconds until cycle cancel chime sounds and drain pump completes sump evacuation.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Ariston Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Ariston FB

FAQ TREE

What does error code FB mean on a Ariston appliance?

Ariston error code FB indicates: Ariston Hotpoint-Ariston 3D Zone Wash MaxiSpace Dishwasher: Motorized Diverter Valve (MDV) microswitch failure FB; cam switch does not pulse during diverter disc positioning..

What is the root cause of Ariston error code FB?

The primary root cause for Ariston code FB is: On Ariston dishwashers: Broken nylon gear teeth in MDV actuator, burnt drive motor winding, or oxidized internal microswitch wiper contacts..

How do I fix or resolve Ariston error code FB?

To resolve error code FB: Measure MDV synchronous drive motor resistance (6.0–7.5 kΩ). Check microswitch continuity with manual gear rotation (must switch between 0 Ω and infinite). Replace MDV. Hold Start/Reset key for 5 seconds until cycle cancel chime sounds and drain pump completes sump evacuation.

Is it safe to clear Ariston error code FB by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Ariston code FB persists, the physical component causing On Ariston dishwashers: Broken nylon gear teeth in MDV actuator, burnt drive motor winding, or oxidized internal microswitch wiper contacts. must be inspected or replaced.

How do I test electrical resistance for Ariston code FB using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Drain Pump Motor Stator Coils across Across pump motor spade terminals (L-N unclipped). Expected nominal reading is 160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC). Tolerance: ±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ..

What safety protocol must be followed before servicing Ariston code FB?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEFB

Ariston // OFFICIAL DIAGNOSTIC BENCH

Ariston FB

DishwasherDrainage System & Drain Pump

Dishwasher

Other Brands Sharing Code FB:WhirlpoolFB IndesitFB BauknechtFB PhilipsFB HotpointFB IgnisFB

Symptom / Description

FAULT

Ariston Hotpoint-Ariston 3D Zone Wash MaxiSpace Dishwasher: Motorized Diverter Valve (MDV) microswitch failure FB; cam switch does not pulse during diverter disc positioning.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Ariston dishwashers: Broken nylon gear teeth in MDV actuator, burnt drive motor winding, or oxidized internal microswitch wiper contacts.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Ariston Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Ariston FB

FAQ TREE

What does error code FB mean on a Ariston appliance?

What is the root cause of Ariston error code FB?

The primary root cause for Ariston code FB is: On Ariston dishwashers: Broken nylon gear teeth in MDV actuator, burnt drive motor winding, or oxidized internal microswitch wiper contacts..

How do I fix or resolve Ariston error code FB?

Is it safe to clear Ariston error code FB by resetting power?

How do I test electrical resistance for Ariston code FB using a multimeter?

What safety protocol must be followed before servicing Ariston code FB?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Ariston FB

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Ariston FB

Community Verification

Related Ariston Dishwasher Error Codes

Ariston FB

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Ariston FB

Community Verification

Related Ariston Dishwasher Error Codes