Skip to content
CodesErreur.comSWISS PRO ENGINE
Core Diagnostics
DiagnosticsBrandsOEM ManualsSpecialistsAI EngineerPRO
Workshop Tools
Diagnostic ToolsNEW
Hardware interfaces & test probes
Find Rating Plate
Locate exact E-Nr, PNC & serial codes
Parts Locator
Global OEM spare parts suppliers
Community & Career
Academy & Courses
Masterclasses by senior technicians
Certification ExamsPRO
Verify your B2B technical credentials
Elite Forum
Peer-to-peer field troubleshooting
Tech Jobs
B2B recruitment & field opportunities
Leaderboard
Global ranking of verified specialists
Certified Appliance Engineering EcosystemApply for Certification →
Language Selector
ENFRDEITESPT
ENEnglishFRFrançaisDEDeutschITItalianoESEspañolPTPortuguês
Account & Access
Upgrade PRO
Back to Search
OEM VERIFIED BENCH
OFFICIAL FAULT CODEE10
Beko
Beko // OFFICIAL DIAGNOSTIC BENCH

Beko Dishwasher E10

DishwasherDrainage System & Drain Pump
Premium built-in dishwasher with open illuminated stainless steel interior and precision spray arms
Dishwasher
Select Appliance Type
0ms Instant Telemetry Switch
Other Brands Sharing Code E10:BoschE10SiemensE10SamsungE10LGE10ElectroluxE10AEGE10HaierE10CandyE10NeffE10V-ZugE10

Symptom / Description

FAULT

Beko CornerIntense / DeepWash / AutoDose Full-Size Dishwasher: Appliance configuration error E10; microcontroller firmware detects model ID mismatch or corrupted cycle EEPROM parameters.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Beko dishwashers utilizing CornerIntense three-arm rectangular washing motion, DeepWash targeted bottle jet zone, and SelFit self-balancing door: Unprogrammed replacement power module installed, electrical surge corruption, or defective flash memory bank.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED
1Cycle mains power for 5 minutes. If code returns, configure appliance model variant code via diagnostic service menu or flash service tool. Press and hold the Start/Cancel button for 3 seconds until status LED flashes. Close door to let pump evacuate water for 30s, then power off.
AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time
AI WORKSHOP PROTOCOL ENGINE
Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH
Need Help? Call a Certified TechnicianWorldwide Beko Parts Finder
Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

SWISS ATELIER TECHNICAL BLUEPRINT // 2026 SCHEMATIC STANDARD

Hydraulic & Drainage Loop

Drain Pump M2, Impeller Chamber, Sump Filter & Analog Pressostat

CALIBRATED TEST POINTS (TP1 / TP2)
ACTIVE MULTIMETER BENCH
MAIN PCB CONTROLLER32-BIT MCUFIRMWARE v26.4SOLID-STATE RELAYTRIAC TY1 // 16A 600V230V AC MAINSLINE FILTER L-NJ1J2TP1TP2PRECISION BENCH METERAUTO-RANGE ΩCAT III168.4 ΩVΩCOMDRAIN PUMP M2DRAIN OUTFLOWRATED COIL: 150-280Ω
Target Component
Drain Pump Motor Stator Coils
Nominal Resistance / Test Range
160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)
Test Harness Pins
Across pump motor spade terminals (L-N unclipped)
Diagnostic Verification Rule
Measure coil resistance unplugged. If OL (open loop) or < 50 Ω (shorted), replace pump assembly.
CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher
2. Multimeter & Electrical Bench Tests (Ω)
MODE: OHMMETER (Ω)AUTO-RANGE
Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board
CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)
Nominal Resistance (Ω)
160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL
0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)
▲ NOMINAL OPERATING WINDOW
Target Component:Drain Pump Motor Stator Coils
Test Pins & Connections
PROBE (+)
PROBE (-)
Across pump motor spade terminals (L-N unclipped)
Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.
1. Pre-Intervention Electrical Safety Protocols
  • !Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
  • !Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
  • !Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.
3. Preliminary Mechanical & Visual Checks
  • Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
  • Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
  • Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.
Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Beko E10

FAQ TREE
What does error code E10 mean on a Beko appliance?

Beko error code E10 indicates: Beko CornerIntense / DeepWash / AutoDose Full-Size Dishwasher: Appliance configuration error E10; microcontroller firmware detects model ID mismatch or corrupted cycle EEPROM parameters..

What is the root cause of Beko error code E10?

The primary root cause for Beko code E10 is: On Beko dishwashers utilizing CornerIntense three-arm rectangular washing motion, DeepWash targeted bottle jet zone, and SelFit self-balancing door: Unprogrammed replacement power module installed, electrical surge corruption, or defective flash memory bank..

How do I fix or resolve Beko error code E10?

To resolve error code E10: Cycle mains power for 5 minutes. If code returns, configure appliance model variant code via diagnostic service menu or flash service tool. Press and hold the Start/Cancel button for 3 seconds until status LED flashes. Close door to let pump evacuate water for 30s, then power off.

Is it safe to clear Beko error code E10 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Beko code E10 persists, the physical component causing On Beko dishwashers utilizing CornerIntense three-arm rectangular washing motion, DeepWash targeted bottle jet zone, and SelFit self-balancing door: Unprogrammed replacement power module installed, electrical surge corruption, or defective flash memory bank. must be inspected or replaced.

How do I test electrical resistance for Beko code E10 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Drain Pump Motor Stator Coils across Across pump motor spade terminals (L-N unclipped). Expected nominal reading is 160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC). Tolerance: ±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ..

What safety protocol must be followed before servicing Beko code E10?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

What does Beko error code E10 mean on a Dishwasher?

Beko error code E10 on a Dishwasher indicates: Beko CornerIntense / DeepWash / AutoDose Full-Size Dishwasher: Appliance configuration error E10; microcontroller firmware detects model ID mismatch or corrupted cycle EEPROM parameters.. Primary cause: On Beko dishwashers utilizing CornerIntense three-arm rectangular washing motion, DeepWash targeted bottle jet zone, and SelFit self-balancing door: Unprogrammed replacement power module installed, electrical surge corruption, or defective flash memory bank.. Recommended solution: Cycle mains power for 5 minutes. If code returns, configure appliance model variant code via diagnostic service menu or flash service tool. Press and hold the Start/Cancel button for 3 seconds until status LED flashes. Close door to let pump evacuate water for 30s, then power off..

What does Beko error code E10 mean on a Tumble Dryer?

Beko error code E10 on a Tumble Dryer indicates: Beko RapiDry / EcoGentle / IronFinish Heat Pump Tumble Dryer: Condenser heat exchanger blocked E10; internal casing temperature rises excessively and drying time doubles.. Primary cause: On Beko dryers with RapiDry hybrid heat-pump and heater system, EcoGentle low-temperature drying, and AquaWave gentle drum paddles: Dense mat of microfibers compacted deep between condenser cooling aluminum fins, choking heat dissipation.. Recommended solution: Remove or open condenser maintenance hatch. Vacuum fins gently using a soft brush attachment. Straighten bent cooling fins with a fin comb. Turn cycle selector to Off. Press and hold Start/Pause and Anti-Crease buttons simultaneously for 5 seconds until memory clears..

What does Beko error code E10 mean on a Hob?

Beko error code E10 on a Hob indicates: Beko IndyFlex / AutoCook / FlameReady Induction Cooktop: High-frequency resonance circuit capacitor degradation E10; induction zones hum loudly or fault under medium power settings.. Primary cause: On Beko cooktops with IndyFlex bridgeable cooking zones, 9-level digital power regulation, and OverFlow safety automatic cutoff: Capacitance loss or dielectric breakdown in high-voltage polypropylene snubber film capacitors (typically 0.47 µF–0.68 µF / 1000V DC).. Recommended solution: Desolder resonant film capacitors from inverter board. Test value with LCR capacitance meter: replace any component deviating by >5% from nominal rating. Wipe glass surface dry. Turn off power at fuse box for 60 seconds. Switch back on and hold the Key Lock sensor for 3 seconds..

What does Beko error code E10 mean on a Oven?

Beko error code E10 on a Oven indicates: Beko AeroPerfect / Split&Cook / CookSense Pyrolytic Built-in Oven: Door contact position switch defect E10; oven fails to detect closed door, cavity lights remain on or baking cycle stops.. Primary cause: On Beko ovens with AeroPerfect uniform hot air aerodynamics, Split&Cook independent cooking cavities, and high-density pyrolytic enamel: Misaligned push pin on door frame, broken actuator spring in microswitch, or scorched switch contacts (<0.5 Ω closed).. Recommended solution: Inspect door switch push rod at top/side of cavity. Measure switch contact resistance: must read <0.5 Ω when pressed in, open when released. Replace switch if faulty. Set cooking dials to 0. Isolate power at the consumer circuit breaker panel for 60 seconds. Restore power and reset the digital timer..

What does Beko error code E10 mean on a Refrigerator / Freezer?

Beko error code E10 on a Refrigerator / Freezer indicates: Beko HarvestFresh / EverFresh+ / NeoFrost Dual Cooling Refrigerator: Door ajar position switch failure E10; alarm beeps continuously with door firmly shut and interior lights fail to turn off.. Primary cause: On Beko refrigeration units with HarvestFresh 3-color light technology simulating solar cycle, EverFresh+ humidity regulation, and NeoFrost dual cooling: Dislodged door gasket magnet, broken reed switch in top header panel, or severed door hinge wiring harness.. Recommended solution: Pass a small neodymium magnet across reed switch location to test contact closure (<0.5 Ω). Inspect door hinge harness for fractured wires. Replace reed board if open. Press and hold the Quick Cool and Freezer Temp keys together for 5 seconds until the display beeps and clears error register..

What does Beko error code E10 mean on a Washing Machine?

Beko error code E10 on a Washing Machine indicates: Beko ProSmart Inverter / AquaTech / SteamCure Front-Loading Washer: Water level sensing error E10; analog pressure sensor output frequency outside calibrated operational bounds (21–27 kHz).. Primary cause: On Beko washing machines utilizing ProSmart Inverter brushless motor, AquaTech water-detergent premixing, and SteamCure anti-crease steam injection: Soap scum clogging pressure bell chamber, pinholed pressure transducer hose, or internal LC oscillator fault.. Recommended solution: Disconnect and flush pressure bell with warm water. Inspect silicone hose for punctures. Measure sensor supply voltage (5V DC) and signal pin. Press and hold Start/Pause key for 4 seconds until program cancellation tone sounds. Turn selector dial to Off, wait 10 seconds, then restart..

Community Verification

COMMUNITY

Did this solution resolve the issue?

Beko E10 — Multi-Appliance Technical Reference

Verified OEM diagnostic specifications across all appliance systems sharing this fault code.

Beko E10 — Dishwasher

[ACTIVE]
Symptom / Description:

Beko CornerIntense / DeepWash / AutoDose Full-Size Dishwasher: Appliance configuration error E10; microcontroller firmware detects model ID mismatch or corrupted cycle EEPROM parameters.

Root Cause:

On Beko dishwashers utilizing CornerIntense three-arm rectangular washing motion, DeepWash targeted bottle jet zone, and SelFit self-balancing door: Unprogrammed replacement power module installed, electrical surge corruption, or defective flash memory bank.

Repair Instructions:

Cycle mains power for 5 minutes. If code returns, configure appliance model variant code via diagnostic service menu or flash service tool. Press and hold the Start/Cancel button for 3 seconds until status LED flashes. Close door to let pump evacuate water for 30s, then power off.

Beko E10 — Dryer

Symptom / Description:

Beko RapiDry / EcoGentle / IronFinish Heat Pump Tumble Dryer: Condenser heat exchanger blocked E10; internal casing temperature rises excessively and drying time doubles.

Root Cause:

On Beko dryers with RapiDry hybrid heat-pump and heater system, EcoGentle low-temperature drying, and AquaWave gentle drum paddles: Dense mat of microfibers compacted deep between condenser cooling aluminum fins, choking heat dissipation.

Repair Instructions:

Remove or open condenser maintenance hatch. Vacuum fins gently using a soft brush attachment. Straighten bent cooling fins with a fin comb. Turn cycle selector to Off. Press and hold Start/Pause and Anti-Crease buttons simultaneously for 5 seconds until memory clears.

Beko E10 — Hob

Symptom / Description:

Beko IndyFlex / AutoCook / FlameReady Induction Cooktop: High-frequency resonance circuit capacitor degradation E10; induction zones hum loudly or fault under medium power settings.

Root Cause:

On Beko cooktops with IndyFlex bridgeable cooking zones, 9-level digital power regulation, and OverFlow safety automatic cutoff: Capacitance loss or dielectric breakdown in high-voltage polypropylene snubber film capacitors (typically 0.47 µF–0.68 µF / 1000V DC).

Repair Instructions:

Desolder resonant film capacitors from inverter board. Test value with LCR capacitance meter: replace any component deviating by >5% from nominal rating. Wipe glass surface dry. Turn off power at fuse box for 60 seconds. Switch back on and hold the Key Lock sensor for 3 seconds.

Beko E10 — Oven

Symptom / Description:

Beko AeroPerfect / Split&Cook / CookSense Pyrolytic Built-in Oven: Door contact position switch defect E10; oven fails to detect closed door, cavity lights remain on or baking cycle stops.

Root Cause:

On Beko ovens with AeroPerfect uniform hot air aerodynamics, Split&Cook independent cooking cavities, and high-density pyrolytic enamel: Misaligned push pin on door frame, broken actuator spring in microswitch, or scorched switch contacts (<0.5 Ω closed).

Repair Instructions:

Inspect door switch push rod at top/side of cavity. Measure switch contact resistance: must read <0.5 Ω when pressed in, open when released. Replace switch if faulty. Set cooking dials to 0. Isolate power at the consumer circuit breaker panel for 60 seconds. Restore power and reset the digital timer.

Beko E10 — Refrigerator / Freezer

Symptom / Description:

Beko HarvestFresh / EverFresh+ / NeoFrost Dual Cooling Refrigerator: Door ajar position switch failure E10; alarm beeps continuously with door firmly shut and interior lights fail to turn off.

Root Cause:

On Beko refrigeration units with HarvestFresh 3-color light technology simulating solar cycle, EverFresh+ humidity regulation, and NeoFrost dual cooling: Dislodged door gasket magnet, broken reed switch in top header panel, or severed door hinge wiring harness.

Repair Instructions:

Pass a small neodymium magnet across reed switch location to test contact closure (<0.5 Ω). Inspect door hinge harness for fractured wires. Replace reed board if open. Press and hold the Quick Cool and Freezer Temp keys together for 5 seconds until the display beeps and clears error register.

Beko E10 — Washing Machine

Symptom / Description:

Beko ProSmart Inverter / AquaTech / SteamCure Front-Loading Washer: Water level sensing error E10; analog pressure sensor output frequency outside calibrated operational bounds (21–27 kHz).

Root Cause:

On Beko washing machines utilizing ProSmart Inverter brushless motor, AquaTech water-detergent premixing, and SteamCure anti-crease steam injection: Soap scum clogging pressure bell chamber, pinholed pressure transducer hose, or internal LC oscillator fault.

Repair Instructions:

Disconnect and flush pressure bell with warm water. Inspect silicone hose for punctures. Measure sensor supply voltage (5V DC) and signal pin. Press and hold Start/Pause key for 4 seconds until program cancellation tone sounds. Turn selector dial to Off, wait 10 seconds, then restart.

SEMANTIC KNOWLEDGE GRAPH // BEKO

Related Beko Dishwasher Error Codes

Diagnostic Link Mesh14 OEM Cross-References

Cross-referenced diagnostic codes for technicians inspecting similar component subsystems.

E11Dishwasher
Drainage System & Drain Pump
Beko CornerIntense / DeepWash / AutoDose Full-Size Dishwasher: Communication bus loss E11; d...
Inspect Protocol
E12Dishwasher
Water Level Pressure Switch & Air Dome
Beko CornerIntense / DeepWash / AutoDose Full-Size Dishwasher: Water level sensor mismatch E...
Inspect Protocol
E13Dishwasher
Drainage System & Drain Pump
Beko CornerIntense / DeepWash / AutoDose Full-Size Dishwasher: Detergent dispenser actuator ...
Inspect Protocol
E14Dishwasher
Drainage System & Drain Pump
Beko CornerIntense / DeepWash / AutoDose Full-Size Dishwasher: Active drying system fault E1...
Inspect Protocol
E15Dishwasher
Drainage System & Drain Pump
Beko CornerIntense / DeepWash / AutoDose Full-Size Dishwasher: Power module DC voltage failu...
Inspect Protocol
F01Dishwasher
Drainage System & Drain Pump
Beko CornerIntense / DeepWash / AutoDose Full-Size Dishwasher: BLDC wash pump inverter imbal...
Inspect Protocol
F02Dishwasher
Drainage System & Drain Pump
Beko CornerIntense / DeepWash / AutoDose Full-Size Dishwasher: Water inlet triac short fault...
Inspect Protocol
F03Dishwasher
Water Level Pressure Switch & Air Dome
Beko CornerIntense / DeepWash / AutoDose Full-Size Dishwasher: Foam aeration cavitation faul...
Inspect Protocol
F04Dishwasher
Drainage System & Drain Pump
Beko CornerIntense / DeepWash / AutoDose Full-Size Dishwasher: Door latch status conflict F0...
Inspect Protocol
F05Dishwasher
Water Level Pressure Switch & Air Dome
Beko CornerIntense / DeepWash / AutoDose Full-Size Dishwasher: Thermal safety cutout tripped...
Inspect Protocol
H1Dishwasher
Drainage System & Drain Pump
Beko H1: Water drainage failure detected in Dishwasher; drain pump cannot evacuate water wit...
Inspect Protocol
H2Dishwasher
Water Level Pressure Switch & Air Dome
Beko H2: Water inlet / filling timeout in Dishwasher; appliance fails to fill to minimum ope...
Inspect Protocol
H4Dishwasher
NTC Temperature Sensor & Thermistor
Beko H4: NTC temperature sensor signal out of range (open or short circuit) in Dishwasher.
Inspect Protocol
H5Dishwasher
Drainage System & Drain Pump
Beko H5: Water drainage failure detected in Dishwasher; drain pump cannot evacuate water wit...
Inspect Protocol
CodesErreur.com

Premium appliance diagnostics & repair database.
Powered by AI to help certified technicians worldwide.

Trusted by professionals in CH & FR

Platform

Search DatabasePRO Diagnostic AIPRODiagnostic ToolsBrands

Workshop Tools

Brands (87)OEM ManualsFind Rating PlateParts Locator

For Technicians

SpecialistsTechnician ForumTech JobsPremium

Corporate

Terms of ServicePrivacy PolicyOfficial Swiss Repair Partner: Electroassistance
OPERATIONAL SAFETY SPECIFICATION

SAFETY DISCLAIMER

The technical information, diagnostic guides, error codes, and AI-generated suggestions provided on this website are intended exclusively for certified and qualified professionals. Appliance repair involves severe electrical hazards, high voltages, and mechanical risks that can result in fatal injury or severe property damage. If you are not a trained technician, do not attempt to repair any appliances. CodesErreur assumes no responsibility or liability for any damage, injury, or consequential losses resulting from the use of the information provided on this platform. You use all information entirely at your own risk.

© 2026 CodesErreur. All rights reserved.

Terms of Service Privacy Policy