OEM VERIFIED BENCH

OFFICIAL FAULT CODEE5

Bompani // OFFICIAL DIAGNOSTIC BENCH

Bompani E5

DishwasherDrainage System & Drain Pump

Dishwasher

Other Brands Sharing Code E5:BoschE5 LGE5 ElectroluxE5 AEGE5 BekoE5 HaierE5 CandyE5 ZanussiE5 Arthur MartinE5 PhilipsE5

Symptom / Description

FAULT

Dirty water remains in the bottom of the dishwasher after a cycle.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

The filters are clogged, the drain hose is blocked or kinked, or the drain pump is faulty or obstructed.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Remove and thoroughly clean all filters in the bottom of the dishwasher. Check the drain hose's entire length for kinks or blockages. Inspect the drain pump impeller for debris.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Bompani Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Bompani E5

FAQ TREE

What does error code E5 mean on a Bompani appliance?

Bompani error code E5 indicates: Dirty water remains in the bottom of the dishwasher after a cycle..

What is the root cause of Bompani error code E5?

The primary root cause for Bompani code E5 is: The filters are clogged, the drain hose is blocked or kinked, or the drain pump is faulty or obstructed..

How do I fix or resolve Bompani error code E5?

To resolve error code E5: Remove and thoroughly clean all filters in the bottom of the dishwasher. Check the drain hose's entire length for kinks or blockages. Inspect the drain pump impeller for debris.

Is it safe to clear Bompani error code E5 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Bompani code E5 persists, the physical component causing The filters are clogged, the drain hose is blocked or kinked, or the drain pump is faulty or obstructed. must be inspected or replaced.

How do I test electrical resistance for Bompani code E5 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Drain Pump Motor Stator Coils across Across pump motor spade terminals (L-N unclipped). Expected nominal reading is 160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC). Tolerance: ±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ..

What safety protocol must be followed before servicing Bompani code E5?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEE5

Bompani // OFFICIAL DIAGNOSTIC BENCH

Bompani E5

DishwasherDrainage System & Drain Pump

Dishwasher

Other Brands Sharing Code E5:BoschE5 LGE5 ElectroluxE5 AEGE5 BekoE5 HaierE5 CandyE5 ZanussiE5 Arthur MartinE5 PhilipsE5

Symptom / Description

FAULT

Dirty water remains in the bottom of the dishwasher after a cycle.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

The filters are clogged, the drain hose is blocked or kinked, or the drain pump is faulty or obstructed.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Remove and thoroughly clean all filters in the bottom of the dishwasher. Check the drain hose's entire length for kinks or blockages. Inspect the drain pump impeller for debris.

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Bompani Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Bompani E5

FAQ TREE

What does error code E5 mean on a Bompani appliance?

Bompani error code E5 indicates: Dirty water remains in the bottom of the dishwasher after a cycle..

What is the root cause of Bompani error code E5?

The primary root cause for Bompani code E5 is: The filters are clogged, the drain hose is blocked or kinked, or the drain pump is faulty or obstructed..

How do I fix or resolve Bompani error code E5?

Is it safe to clear Bompani error code E5 by resetting power?

How do I test electrical resistance for Bompani code E5 using a multimeter?

What safety protocol must be followed before servicing Bompani code E5?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Bompani E5

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Bompani E5

Community Verification

Related Bompani Dishwasher Error Codes

Bompani E5

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Bompani E5

Community Verification

Related Bompani Dishwasher Error Codes