OEM VERIFIED BENCH

OFFICIAL FAULT CODEF14

Faber // OFFICIAL DIAGNOSTIC BENCH

Faber F14

DishwasherDrainage System & Drain Pump

Dishwasher

Other Brands Sharing Code F14:MieleF14 WhirlpoolF14 IndesitF14 BauknechtF14 V-ZugF14 AristonF14 LiebherrF14 ScholtèsF14 Schaub LorenzF14 BaumaticF14

Symptom / Description

FAULT

Faber Silence Pro 42dB / Integrated Smart Touch Dishwasher: Diagnostic fault code F14 registered by the microcomputer controller. Main control board EEPROM checksum error.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Faber appliances engineered with Inverter-driven high-pressure circulation pump, ActiveDry automatic door release, and optical turbidity wash sensor: configuration profile corrupted in non-volatile memory. Metrological tolerance verification: drain pump synchronous motor coil nominal 165 Ω to 180 Ω (230V AC).

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: measure drain pump coil resistance across terminals (expected ~170 Ω). Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Open dishwasher door slightly, press and hold the Start/Reset button for 4 seconds until the active program LED turns off and the drain pump runs for 30 seconds. Power off, wait 10 seconds, then power on.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Faber Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Faber F14

FAQ TREE

What does error code F14 mean on a Faber appliance?

Faber error code F14 indicates: Faber Silence Pro 42dB / Integrated Smart Touch Dishwasher: Diagnostic fault code F14 registered by the microcomputer controller. Main control board EEPROM checksum error..

What is the root cause of Faber error code F14?

The primary root cause for Faber code F14 is: On Faber appliances engineered with Inverter-driven high-pressure circulation pump, ActiveDry automatic door release, and optical turbidity wash sensor: configuration profile corrupted in non-volatile memory. Metrological tolerance verification: drain pump synchronous motor coil nominal 165 Ω to 180 Ω (230V AC)..

How do I fix or resolve Faber error code F14?

To resolve error code F14: Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: measure drain pump coil resistance across terminals (expected ~170 Ω). Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Open dishwasher door slightly, press and hold the Start/Reset button for 4 seconds until the active program LED turns off and the drain pump runs for 30 seconds. Power off, wait 10 seconds, then power on.

Is it safe to clear Faber error code F14 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Faber code F14 persists, the physical component causing On Faber appliances engineered with Inverter-driven high-pressure circulation pump, ActiveDry automatic door release, and optical turbidity wash sensor: configuration profile corrupted in non-volatile memory. Metrological tolerance verification: drain pump synchronous motor coil nominal 165 Ω to 180 Ω (230V AC). must be inspected or replaced.

How do I test electrical resistance for Faber code F14 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Drain Pump Motor Stator Coils across Across pump motor spade terminals (L-N unclipped). Expected nominal reading is 160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC). Tolerance: ±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ..

What safety protocol must be followed before servicing Faber code F14?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEF14

Faber // OFFICIAL DIAGNOSTIC BENCH

Faber F14

DishwasherDrainage System & Drain Pump

Dishwasher

Other Brands Sharing Code F14:MieleF14 WhirlpoolF14 IndesitF14 BauknechtF14 V-ZugF14 AristonF14 LiebherrF14 ScholtèsF14 Schaub LorenzF14 BaumaticF14

Symptom / Description

FAULT

Faber Silence Pro 42dB / Integrated Smart Touch Dishwasher: Diagnostic fault code F14 registered by the microcomputer controller. Main control board EEPROM checksum error.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Faber Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Faber F14

FAQ TREE

What does error code F14 mean on a Faber appliance?

What is the root cause of Faber error code F14?

How do I fix or resolve Faber error code F14?

Is it safe to clear Faber error code F14 by resetting power?

How do I test electrical resistance for Faber code F14 using a multimeter?

What safety protocol must be followed before servicing Faber code F14?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Faber F14

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Faber F14

Community Verification

Related Faber Dishwasher Error Codes

Faber F14

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Faber F14

Community Verification

Related Faber Dishwasher Error Codes