OEM VERIFIED BENCH

OFFICIAL FAULT CODEi20

FAGOR // OFFICIAL DIAGNOSTIC BENCH

FAGOR i20

DishwasherDrainage System & Drain Pump

Dishwasher

Other Brands Sharing Code i20:ElectroluxI20 AEGI20 V-ZugI20 ZanussiI20 Arthur MartinI20 SchulthessI20 Schaub LorenzI20 AirluxI20 AtlanticI20 CastorI20

Symptom / Description

FAULT

FAGOR I20: Water drainage failure detected in Dishwasher; drain pump cannot evacuate water within safety time limit.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

Drain filters are blocked with food debris, or the drain hose is obstructed.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Pause the cycle. Remove and thoroughly clean the filters in the bottom of the dishwasher. Check the drain hose is not kinked.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide FAGOR Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: FAGOR I20

FAQ TREE

What does error code I20 mean on a FAGOR appliance?

FAGOR error code I20 indicates: FAGOR I20: Water drainage failure detected in Dishwasher; drain pump cannot evacuate water within safety time limit..

What is the root cause of FAGOR error code I20?

The primary root cause for FAGOR code I20 is: Drain filters are blocked with food debris, or the drain hose is obstructed..

How do I fix or resolve FAGOR error code I20?

To resolve error code I20: Pause the cycle. Remove and thoroughly clean the filters in the bottom of the dishwasher. Check the drain hose is not kinked.

Is it safe to clear FAGOR error code I20 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if FAGOR code I20 persists, the physical component causing Drain filters are blocked with food debris, or the drain hose is obstructed. must be inspected or replaced.

How do I test electrical resistance for FAGOR code I20 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Drain Pump Motor Stator Coils across Across pump motor spade terminals (L-N unclipped). Expected nominal reading is 160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC). Tolerance: ±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ..

What safety protocol must be followed before servicing FAGOR code I20?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEi20

FAGOR // OFFICIAL DIAGNOSTIC BENCH

FAGOR i20

DishwasherDrainage System & Drain Pump

Dishwasher

Other Brands Sharing Code i20:ElectroluxI20 AEGI20 V-ZugI20 ZanussiI20 Arthur MartinI20 SchulthessI20 Schaub LorenzI20 AirluxI20 AtlanticI20 CastorI20

Symptom / Description

FAULT

FAGOR I20: Water drainage failure detected in Dishwasher; drain pump cannot evacuate water within safety time limit.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

Drain filters are blocked with food debris, or the drain hose is obstructed.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Pause the cycle. Remove and thoroughly clean the filters in the bottom of the dishwasher. Check the drain hose is not kinked.

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide FAGOR Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: FAGOR I20

FAQ TREE

What does error code I20 mean on a FAGOR appliance?

FAGOR error code I20 indicates: FAGOR I20: Water drainage failure detected in Dishwasher; drain pump cannot evacuate water within safety time limit..

What is the root cause of FAGOR error code I20?

The primary root cause for FAGOR code I20 is: Drain filters are blocked with food debris, or the drain hose is obstructed..

How do I fix or resolve FAGOR error code I20?

To resolve error code I20: Pause the cycle. Remove and thoroughly clean the filters in the bottom of the dishwasher. Check the drain hose is not kinked.

Is it safe to clear FAGOR error code I20 by resetting power?

How do I test electrical resistance for FAGOR code I20 using a multimeter?

What safety protocol must be followed before servicing FAGOR code I20?

Community Verification

COMMUNITY

Did this solution resolve the issue?

FAGOR i20

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: FAGOR I20

Community Verification

Related FAGOR Dishwasher Error Codes

FAGOR i20

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: FAGOR I20

Community Verification

Related FAGOR Dishwasher Error Codes