Field Actions
DISPATCHAlways disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.
Frequently Asked Questions: Gree / Mace E5
FAQ TREEWhat does error code E5 mean on a Gree-Mace appliance?
Gree-Mace error code E5 indicates: Gree-Mace G10 Inverter / Free Match / GMV5 / GMV6 Multi-VRF Commercial & Residential HVAC: Diagnostic fault code E5 registered by the microcomputer controller. AC mains input overcurrent or IPM instantaneous peak current protection.
What is the root cause of Gree-Mace error code E5?
The primary root cause for Gree-Mace code E5 is: On Gree-Mace appliances engineered with Gree G10 Inverter low-frequency torque control, intelligent dual-stage rotary compressor, 46 Ω electronic expansion valve stepping motor coils, high-voltage PFC boost circuit (380V DC), and precision NTC thermistors (15 kΩ ambient, 20 kΩ coil, 50 kΩ discharge): AC mains input overcurrent or IPM instantaneous peak current caused by low supply voltage or compressor mechanical binding Metrological tolerance verification: AC current transformer (CT) output 0V to 3.3V DC; compressor running current exceeding rated nameplate..
How do I fix or resolve Gree-Mace error code E5?
To resolve error code E5: Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: measure AC line current with clamp meter and verify AC supply voltage stability under load. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Using the remote controller: point at the unit and press 'LIGHT' 6 times in 3 seconds (or hold 'TURBO' + 'MODE' for 5 seconds) to enter diagnostic query mode. For inverter lockout errors (H5, HC, P0, P8, E6), switch off the external electrical isolator / circuit breaker for at least 3 minutes to allow DC bus capacitors to fully discharge.
Is it safe to clear Gree-Mace error code E5 by resetting power?
Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Gree-Mace code E5 persists, the physical component causing On Gree-Mace appliances engineered with Gree G10 Inverter low-frequency torque control, intelligent dual-stage rotary compressor, 46 Ω electronic expansion valve stepping motor coils, high-voltage PFC boost circuit (380V DC), and precision NTC thermistors (15 kΩ ambient, 20 kΩ coil, 50 kΩ discharge): AC mains input overcurrent or IPM instantaneous peak current caused by low supply voltage or compressor mechanical binding Metrological tolerance verification: AC current transformer (CT) output 0V to 3.3V DC; compressor running current exceeding rated nameplate. must be inspected or replaced.
How do I test electrical resistance for Gree-Mace code E5 using a multimeter?
Set a digital multimeter to ohms (Ω). Disconnect power and test NTC Temperature Sensor Probe (Thermistor) across Across sensor pins 1-2 (unplugged harness). Expected nominal reading is 4.8kΩ–12kΩ (at 20°C–25°C). Tolerance: Negative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit..
What safety protocol must be followed before servicing Gree-Mace code E5?
Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.
Community Verification
COMMUNITYDid this solution resolve the issue?



