OEM VERIFIED BENCH

OFFICIAL FAULT CODECLr

Hoover // OFFICIAL DIAGNOSTIC BENCH

Hoover CLr

Washing MachineDrainage System & Drain Pump

Washing Machine

Other Brands Sharing Code CLr:HaierCLR CandyCLR RosieresCLR GECLR IbernaCLR ZerowattCLR

Symptom / Description

FAULT

Hoover H-WASH 300 / 500 / 700 Eco-Power Inverter Washer: Tub clean safety drain prompt CLr; automated maintenance rinse cycle or reminder to clean drum interior.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Hoover washers utilizing Eco-Power permanent magnet brushless motor, Power Care System premix injection, and hOn AI intelligence: Machine cycle counter has reached threshold (typically 50 wash cycles) without a high-temperature Tub Clean cycle.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Empty the drum completely, add machine descaler or oxygen bleach directly into drum, select Tub Clean program, and allow complete 90°C cycle to finish. Rotate dial to Off, hold down Start/Pause and Spin Speed keys for 6 seconds until 'rES' appears on the digital readout, then power cycle.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Hoover Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpWashing Machine

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Hoover CLR

FAQ TREE

What does error code CLR mean on a Hoover appliance?

Hoover error code CLR indicates: Hoover H-WASH 300 / 500 / 700 Eco-Power Inverter Washer: Tub clean safety drain prompt CLr; automated maintenance rinse cycle or reminder to clean drum interior..

What is the root cause of Hoover error code CLR?

The primary root cause for Hoover code CLR is: On Hoover washers utilizing Eco-Power permanent magnet brushless motor, Power Care System premix injection, and hOn AI intelligence: Machine cycle counter has reached threshold (typically 50 wash cycles) without a high-temperature Tub Clean cycle..

How do I fix or resolve Hoover error code CLR?

To resolve error code CLR: Empty the drum completely, add machine descaler or oxygen bleach directly into drum, select Tub Clean program, and allow complete 90°C cycle to finish. Rotate dial to Off, hold down Start/Pause and Spin Speed keys for 6 seconds until 'rES' appears on the digital readout, then power cycle.

Is it safe to clear Hoover error code CLR by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Hoover code CLR persists, the physical component causing On Hoover washers utilizing Eco-Power permanent magnet brushless motor, Power Care System premix injection, and hOn AI intelligence: Machine cycle counter has reached threshold (typically 50 wash cycles) without a high-temperature Tub Clean cycle. must be inspected or replaced.

How do I test electrical resistance for Hoover code CLR using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Drain Pump Motor Stator Coils across Across pump motor spade terminals (L-N unclipped). Expected nominal reading is 160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC). Tolerance: ±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ..

What safety protocol must be followed before servicing Hoover code CLR?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODECLr

Hoover // OFFICIAL DIAGNOSTIC BENCH

Hoover CLr

Washing MachineDrainage System & Drain Pump

Washing Machine

Other Brands Sharing Code CLr:HaierCLR CandyCLR RosieresCLR GECLR IbernaCLR ZerowattCLR

Symptom / Description

FAULT

Hoover H-WASH 300 / 500 / 700 Eco-Power Inverter Washer: Tub clean safety drain prompt CLr; automated maintenance rinse cycle or reminder to clean drum interior.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Hoover Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpWashing Machine

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Hoover CLR

FAQ TREE

What does error code CLR mean on a Hoover appliance?

Hoover error code CLR indicates: Hoover H-WASH 300 / 500 / 700 Eco-Power Inverter Washer: Tub clean safety drain prompt CLr; automated maintenance rinse cycle or reminder to clean drum interior..

What is the root cause of Hoover error code CLR?

How do I fix or resolve Hoover error code CLR?

Is it safe to clear Hoover error code CLR by resetting power?

How do I test electrical resistance for Hoover code CLR using a multimeter?

What safety protocol must be followed before servicing Hoover code CLR?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Hoover CLr

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Hoover CLR

Community Verification

Related Hoover Washing Machine Error Codes

Hoover CLr

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Hoover CLR

Community Verification

Related Hoover Washing Machine Error Codes