Skip to content
CodesErreur.comSWISS PRO ENGINE
Core Diagnostics
DiagnosticsBrandsOEM ManualsSpecialistsAI EngineerPRO
Workshop Tools
Diagnostic ToolsNEW
Hardware interfaces & test probes
Find Rating Plate
Locate exact E-Nr, PNC & serial codes
Parts Locator
Global OEM spare parts suppliers
Community & Career
Academy & Courses
Masterclasses by senior technicians
Certification ExamsPRO
Verify your B2B technical credentials
Elite Forum
Peer-to-peer field troubleshooting
Tech Jobs
B2B recruitment & field opportunities
Leaderboard
Global ranking of verified specialists
Certified Appliance Engineering EcosystemApply for Certification →
Language Selector
Account & Access
Upgrade PRO
Back to Search
OEM VERIFIED BENCH
OFFICIAL FAULT CODEE02
Iberna
Iberna // OFFICIAL DIAGNOSTIC BENCH

Iberna E02

Washing MachineWater Inlet Valve, Aquastop & Flowmeter
Luxury front-loading washing machine in brushed titanium with illuminated dark glass drum
Washing Machine
Other Brands Sharing Code E02:BoschE02ElectroluxE02AEGE02CandyE02HooverE02ZanussiE02Arthur MartinE02GaggenauE02RosieresE02Schaub LorenzE02

Symptom / Description

FAULT

Water fill fault. Machine does not fill with water or fills very slowly.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

Water supply is turned off, inlet hose is kinked or blocked, or the water inlet valve is faulty.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED
1Check that the water tap is fully open. Inspect the inlet hose for kinks or blockages. Test and replace the water inlet valve if necessary.
AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time
AI WORKSHOP PROTOCOL ENGINE
Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH
Need Help? Call a Certified TechnicianWorldwide Iberna Parts Finder
Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLWater Inlet Valve, Aquastop & FlowmeterWashing Machine
2. Multimeter & Electrical Bench Tests (Ω)
MODE: OHMMETER (Ω)AUTO-RANGE
Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board
CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)
Nominal Resistance (Ω)
3.5kΩ–4.5kΩ (Standard 230V) / 2.0kΩ–4.2kΩ (Aquastop)NOMINAL
0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)
▲ NOMINAL OPERATING WINDOW
Target Component:Solenoid Valve Coil / Aquastop Pneumatic Valve
Test Pins & Connections
PROBE (+)
PROBE (-)
Across coil spade terminals (disconnect harness first)
Tolerance & Diagnostic Criteria±10%. Open circuit (OL) indicates burned solenoid coil. Flowmeter turbine reed switch pulses on flow.
1. Pre-Intervention Electrical Safety Protocols
  • !Electrical Safety Protocol: Disconnect electrical power before touching solenoid valve coils or Aquastop connectors.
  • !Firmly shut off the domc water supply tap before unscrewing the inlet hose fitting.
  • !Check safety base drip tray for accumulated water triggering the anti-flood polystyrene float switch.
3. Preliminary Mechanical & Visual Checks
  • Remove and clean sediment and sand particles from the 3/4" inlet hose metal mesh filter.
  • Verify domestic dynamic water pressure is between 1.0 and 10.0 bar (0.1 to 1.0 MPa).
  • Inspect outer Aquastop hose jacket for expansion, pinch damage, or internal leak reservoir triggering.
Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Iberna E02

FAQ TREE
What does error code E02 mean on a Iberna appliance?

Iberna error code E02 indicates: Water fill fault. Machine does not fill with water or fills very slowly..

What is the root cause of Iberna error code E02?

The primary root cause for Iberna code E02 is: Water supply is turned off, inlet hose is kinked or blocked, or the water inlet valve is faulty..

How do I fix or resolve Iberna error code E02?

To resolve error code E02: Check that the water tap is fully open. Inspect the inlet hose for kinks or blockages. Test and replace the water inlet valve if necessary.

Is it safe to clear Iberna error code E02 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Iberna code E02 persists, the physical component causing Water supply is turned off, inlet hose is kinked or blocked, or the water inlet valve is faulty. must be inspected or replaced.

How do I test electrical resistance for Iberna code E02 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Solenoid Valve Coil / Aquastop Pneumatic Valve across Across coil spade terminals (disconnect harness first). Expected nominal reading is 3.5kΩ–4.5kΩ (Standard 230V) / 2.0kΩ–4.2kΩ (Aquastop). Tolerance: ±10%. Open circuit (OL) indicates burned solenoid coil. Flowmeter turbine reed switch pulses on flow..

What safety protocol must be followed before servicing Iberna code E02?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

SEMANTIC KNOWLEDGE GRAPH // IBERNA

Related Iberna Washing Machine Error Codes

Diagnostic Link Mesh14 OEM Cross-References

Cross-referenced diagnostic codes for technicians inspecting similar component subsystems.

E03Drainage System & Drain Pump
Drainage fault. Water remains in the drum after the cycle.
Inspect Protocol
E04Water Level Pressure Switch & Air Dome
Overfill or anti-flood error. Too much water in the drum.
Inspect Protocol
E05NTC Temperature Sensor & Thermistor
Temperature sensor (NTC) fault. Machine may not heat water or may stop mid-cycle.
Inspect Protocol
E07Drive Motor, Inverter & Tachometer Sensor
Motor fault. The motor may not turn, or it may spin too fast and then stop.
Inspect Protocol
E08Drive Motor, Inverter & Tachometer Sensor
Motor speed sensor fault. Drum may jerk or spin uncontrollably before stopping.
Inspect Protocol
E09Drive Motor, Inverter & Tachometer Sensor
Motor control board (triac) fault. The motor does not run.
Inspect Protocol
E16Heating Element, Thermostat & Safety Fuse
Heating element fault. The machine trips the circuit breaker or does not heat the water.
Inspect Protocol
E01Door Lock Mechanism & Safety Interlock
Door lock fault, machine will not start.
Inspect Protocol
E1Water Inlet Valve, Aquastop & Flowmeter
Water fill timeout. Dishwasher beeps and stops early in the cycle.
Inspect Protocol
E2Drainage System & Drain Pump
Drainage timeout. Water is left in the bottom of the dishwasher.
Inspect Protocol
E3Heating Element, Thermostat & Safety Fuse
Water heating fault. Dishes are not cleaned or dried properly.
Inspect Protocol
E4Water Level Pressure Switch & Air Dome
Water leak or overfill detected. The machine may stop and continuously drain.
Inspect Protocol
E5NTC Temperature Sensor & Thermistor
Temperature sensor (NTC) fault. Program may not run correctly or complete.
Inspect Protocol
F1NTC Temperature Sensor & Thermistor
Freezer temperature is not correct or temperature display is flashing.
Inspect Protocol
CodesErreur.com

Premium appliance diagnostics & repair database.
Powered by AI to help certified technicians worldwide.

Trusted by professionals in CH & FR

Platform

Search DatabasePRO Diagnostic AIPRODiagnostic ToolsBrands

Workshop Tools

Brands (87)OEM ManualsFind Rating PlateParts Locator

For Technicians

SpecialistsTechnician ForumTech JobsPremium

Corporate

Terms of ServicePrivacy PolicyOfficial Swiss Repair Partner: Electroassistance
OPERATIONAL SAFETY SPECIFICATION

SAFETY DISCLAIMER

The technical information, diagnostic guides, error codes, and AI-generated suggestions provided on this website are intended exclusively for certified and qualified professionals. Appliance repair involves severe electrical hazards, high voltages, and mechanical risks that can result in fatal injury or severe property damage. If you are not a trained technician, do not attempt to repair any appliances. CodesErreur assumes no responsibility or liability for any damage, injury, or consequential losses resulting from the use of the information provided on this platform. You use all information entirely at your own risk.

© 2026 CodesErreur. All rights reserved.

Official Swiss Repair Partner: Electroassistance Terms of Service Privacy Policy