Skip to content

CodesErreur.comSWISS PRO ENGINE

Core Diagnostics

Diagnostics Brands OEM Manuals Specialists AI EngineerPRO

Workshop Tools

Diagnostic ToolsNEW

Hardware interfaces & test probes

Find Rating Plate

Locate exact E-Nr, PNC & serial codes

Global OEM spare parts suppliers

Community & Career

Academy & Courses

Masterclasses by senior technicians

Certification ExamsPRO

Verify your B2B technical credentials

Peer-to-peer field troubleshooting

B2B recruitment & field opportunities

Global ranking of verified specialists

Certified Appliance Engineering EcosystemApply for Certification →

Language Selector

Account & Access

Iberna • Central Diagnostic Dictionary

165 Verified Codes in Database

Iberna Error Codes & Diagnostics

Access our premium database of error codes, common faults, and professional repair solutions for Iberna appliances.

Luxury front-loading washing machine in brushed titanium with illuminated dark glass drum

CodeAppliancesFault / DiagnosticsRepair InstructionsAction

AL01

Refrigerator / Freezer

Refrigeration Compressor, Defrost Heater & PTC Relay

Iberna IR / Total FrostFree Combi Refrigerator: Critical freezer high temperature alarm AL01; freezer compartment temperature has risen above safe threshold of -9°C.

On Iberna refrigeration units featuring Total FrostFree air circulation evaporator, defrost termination bi-metal, and compressor start relay: Prolonged domestic power outage, freezer door left open, heavy loading of unfrozen food, or refrigerant leak.

Mute acoustic alarm with Alarm Reset button. Activate Super Freeze mode for 12 hours. Verify compressor runs and evaporator chills down to -18°C. Reset: Press and hold Fast Freeze button for 8 seconds until warning buzzer stops sounding, confirming internal microprocessor reset.

AL02

Refrigerator / Freezer

Refrigeration Compressor, Defrost Heater & PTC Relay

Iberna IR / Total FrostFree Combi Refrigerator: Water dispenser filter expiration / flow timeout alarm AL02; water purification filter cartridge life limit or fill slow rate detected.

On Iberna refrigeration units featuring Total FrostFree air circulation evaporator, defrost termination bi-metal, and compressor start relay: 6-month cartridge timer elapsed, clogged carbon block filter, or low household water line pressure (<1.5 bar).

Replace internal water filter cartridge. Flush 5 liters through dispenser to purge air. Press and hold Water Filter Reset button for 3 seconds. Reset: Press and hold Fast Freeze button for 8 seconds until warning buzzer stops sounding, confirming internal microprocessor reset.

AL03

Dishwasher

Drainage System & Drain Pump

Iberna IDI / Standard Wash System Dishwasher: Drain evacuation alarm AL03; sump fails to empty completely during intermediate rinse drain phase.

On Iberna dishwashers powered by Standard Wash System hydraulic circuit, solenoid fill valve control, and heating element flow-through tube: Heavy grease clogs in drain hose, sink siphon nipple blocked, or drain pump motor winding weakened (~160–220 Ω).

Disconnect drain hose from under-sink siphon and verify clear bore. Flush drain hose with warm water. Measure pump motor resistance (~160–220 Ω). Press and hold Start button for 5 seconds until buzzer sounds, close door to allow pump-out cycle to complete, then switch off.

AL05

Dishwasher

Water Inlet Valve, Aquastop & Flowmeter

Iberna IDI / Standard Wash System Dishwasher: Water filling timeout alarm AL05; wash tank does not fill to operating level within program timeout limit.

On Iberna dishwashers utilizing Standard Wash System hydraulic circuit, solenoid fill valve control, and heating element flow-through tube: Scaled water supply tap, blocked metal strainer mesh in inlet hose connector, or defective inlet valve (~3.5–4.5 kΩ).

Check faucet flow rate with bucket test. Remove supply hose and rinse out particulate debris from inlet filter. Measure valve solenoid (~3.5–4.5 kΩ). Press and hold Start button for 5 seconds until buzzer sounds, close door to allow pump-out cycle to complete, then switch off.

CLr

Washing Machine

NTC Temperature Sensor & Thermistor

Iberna ILF / EcoTime Pro Inverter Washing Machine: Tub clean safety drain prompt CLr; automated maintenance rinse cycle or reminder to clean drum interior.

On Iberna washers utilizing reliable GIAS compact micro-controller, high-efficiency wash group, and fast-response NTC thermistors: Machine cycle counter has reached threshold (typically 50 wash cycles) without a high-temperature Tub Clean cycle.

Empty the drum completely, add machine descaler or oxygen bleach directly into drum, select Tub Clean program, and allow complete 90°C cycle to finish. Move program selector to Stop, hold Start/Pause and Spin keys together for 5 seconds until status LEDs extinguish, then restart.

E0

Hob / Cooktop

Electronic Control Board (PCB) & Bus Communications

Iberna IH Touch Induction & Radiant Cooktop: Touch control module initialization error E0; touch interface microcontroller fails internal RAM diagnostic self-test.

On Iberna cooktops utilizing IH Touch induction power converters, radiant coil zones, and touch-sensitive key lockout: Mains supply transient voltage fluctuation during power-up, corrupted microprocessor registers, or dry electrolytic filter cap.

Power off at mains consumer unit for 60 seconds. Restore power and observe initialization. If code reoccurs instantly, replace touch control PCB. Clear moisture from control area, power down circuit breaker for 40 seconds, restore power and touch Lock Key for 5 seconds.

E0

Refrigerator / Freezer

Refrigeration Compressor, Defrost Heater & PTC Relay

Iberna IR / Total FrostFree Combi Refrigerator: Interface display communication error E0; temperature control panel loses serial link with master power PCB.

On Iberna refrigeration units featuring Total FrostFree air circulation evaporator, defrost termination bi-metal, and compressor start relay: Damaged door hinge wire harness, oxidized ribbon connector, or missing 5V DC low-voltage rail.

Inspect top door hinge wiring harness for fatigue breaks. Check 5V DC and 12V DC power pins at display connector CN1. Reset procedure: Press and hold Fast Freeze button for 8 seconds until warning buzzer stops sounding, confirming internal microprocessor reset.

E01

Dishwasher

Water Inlet Valve, Aquastop & Flowmeter

Iberna IDI / Standard Wash System Dishwasher: Water fill solenoid valve circuit fault E01; power board detects open circuit across inlet solenoid coil.

On Iberna dishwashers powered by Standard Wash System hydraulic circuit, solenoid fill valve control, and heating element flow-through tube: Burned inlet valve coil (~3.8 kΩ nominal), corroded connector spade terminals, or broken wire in door hinge harness.

Measure inlet valve coil resistance (~3.5–4.5 kΩ). Inspect wiring harness continuity from control board. Replace valve assembly if coil is infinite ohms. Press and hold Start button for 5 seconds until buzzer sounds, close door to allow pump-out cycle to complete, then switch off.

E01

Tumble Dryer

NTC Temperature Sensor & Thermistor

Iberna ITD AirFlow Condenser Tumble Dryer: Airflow restriction warning E01; door lint filter clogged or lower heat exchanger condenser obstructed with lint.

On Iberna tumble dryers utilizing AirFlow condensation duct system, front/rear NTC temperature sensors, and capacitive run motor: Dense lint coating on fine mesh screen, blocked air passage in lower plinth, or high differential temperature across air duct.

Remove door lint filter and wash under warm tap water; dry before refitting. Open bottom plinth and vacuum condenser aluminum fins. Set selector to 0, hold Start/Pause and Half Heat buttons for 5 seconds until beep acknowledges memory wipe, then return to Off.

E01

Washing Machine

NTC Temperature Sensor & Thermistor

Iberna ILF / EcoTime Pro Inverter Washing Machine: Door interlock error E01; appliance refuses to commence wash cycle because the door latch contact is not verified.

On Iberna washing machines utilizing reliable GIAS compact micro-controller, high-efficiency wash group, and fast-response NTC thermistors: Defective door latch microswitch, laundry pinched in the rubber bellow, or open PTC solenoid coil (~900–1200 Ω).

Verify door latch alignment. Inspect wiring harness between lock and main module. Measure lock coil resistance (~900–1200 Ω across terminals 1-3). Move program selector to Stop, hold Start/Pause and Spin keys together for 5 seconds until status LEDs extinguish, then restart.

E1

Dishwasher

Water Inlet Valve, Aquastop & Flowmeter

Iberna IDI / Standard Wash System Dishwasher: Water inlet fill failure E1; appliance detects no incoming water flow into sump after opening fill valve.

On Iberna dishwashers utilizing Standard Wash System hydraulic circuit, solenoid fill valve control, and heating element flow-through tube: Closed water supply valve, kinked inlet hose, blocked AquaStop mesh filter, or open valve coil (~3.5–4.5 kΩ).

Check water supply tap pressure. Unscrew supply hose and clean AquaStop inlet filter screen. Measure solenoid valve coil (~3.5–4.5 kΩ). Press and hold Start button for 5 seconds until buzzer sounds, close door to allow pump-out cycle to complete, then switch off.

E1

Hob / Cooktop

General System & Mechanical Integration

Iberna IH Touch Induction & Radiant Cooktop: Touch sensor zone covered by object or liquid E1; continuous conductive activation detected on control glass for >10 seconds.

On Iberna cooktops featuring IH Touch induction power converters, radiant coil zones, and touch-sensitive key lockout: Boiled-over cooking liquid, conductive grease, wet cleaning rag, or metal pot lid resting directly over touch sensors.

Remove all cookware from control area. Wipe glass dry using a dry cotton towel. Clean any dried salt or starch residue. Clear moisture from control area, power down circuit breaker for 40 seconds, restore power and touch Lock Key for 5 seconds.

E1

Refrigerator / Freezer

Refrigeration Compressor, Defrost Heater & PTC Relay

Iberna IR / Total FrostFree Combi Refrigerator: Refrigerator compartment temperature sensor fault E1; fresh food section thermistor circuit open or shorted.

On Iberna refrigeration units featuring Total FrostFree air circulation evaporator, defrost termination bi-metal, and compressor start relay: Drifted NTC sensing bead, moisture ingress behind cabinet liner, or degraded wiring connector.

Measure NTC resistance at main PCB connector: standard value is ~5 kΩ at 25°C, rising to ~16.3 kΩ at 0°C. Replace sensor if out of tolerance. Reset: Press and hold Fast Freeze button for 8 seconds until warning buzzer stops sounding, confirming internal microprocessor reset.

E1

Washing Machine

NTC Temperature Sensor & Thermistor

Iberna ILF / EcoTime Pro Inverter Washing Machine: Water drainage failure E1; machine unable to drain water from wash tub within 4 minutes.

On Iberna washers utilizing reliable GIAS compact micro-controller, high-efficiency wash group, and fast-response NTC thermistors: Blocked coin trap filter, kinked drain hose, pump impeller jammed by foreign object, or pump motor coil open (~160–220 Ω).

Clean drain pump filter at lower front. Verify free impeller rotation. Check pump resistance (~160–220 Ω across terminals). Move program selector to Stop, hold Start/Pause and Spin keys together for 5 seconds until status LEDs extinguish, then restart.

E02

Dishwasher

Water Inlet Valve, Aquastop & Flowmeter

Iberna IDI / Standard Wash System Dishwasher: Fill meter pulse count error E02; turbine sensor signals water fill but pulse frequency is erratic or dropping out.

On Iberna dishwashers featuring Standard Wash System hydraulic circuit, solenoid fill valve control, and heating element flow-through tube: Magnet pin loose in flowmeter impeller, limescale accumulation inside water jacket labyrinth, or oxidized plug contacts.

Inspect left-side plastic air break for scale deposits. Clean electrical contacts on reed switch PCB with contact spray. Replace air break if impeller sticks. Press and hold Start button for 5 seconds until buzzer sounds, close door to allow pump-out cycle to complete, then switch off.

E02

Tumble Dryer

NTC Temperature Sensor & Thermistor

Iberna ITD AirFlow Condenser Tumble Dryer: Process air duct NTC sensor error E02; thermistor signal indicates circuit open, short, or temperature out of operating range.

On Iberna tumble dryers powered by AirFlow condensation duct system, front/rear NTC temperature sensors, and capacitive run motor: Defective front airflow NTC thermistor bead (~20.0 kΩ at 25°C), disconnected spade terminals, or wire chafing.

Locate NTC probe at front blower duct. Disconnect wire terminals and measure resistance (~20.0 kΩ at 25°C, ~4.5 kΩ at 60°C). Replace if open. Set selector to 0, hold Start/Pause and Half Heat buttons for 5 seconds until beep acknowledges memory wipe, then return to Off.

E02

Washing Machine

NTC Temperature Sensor & Thermistor

Iberna ILF / EcoTime Pro Inverter Washing Machine: Water inlet fill timeout E02; tub does not reach the minimum operating water level within 210 seconds of valve energization.

On Iberna washing machines with reliable GIAS compact micro-controller, high-efficiency wash group, and fast-response NTC thermistors: Closed tap, kinked fill hose, clogged inlet valve mesh filter, or open solenoid coil (~3.5–4.5 kΩ).

Confirm mains water flow rate (>10 L/min). Clean the inlet filter screen. Check dual solenoid valve coil resistances (~3.5–4.5 kΩ). Move program selector to Stop, hold Start/Pause and Spin keys together for 5 seconds until status LEDs extinguish, then restart.

E2

Dishwasher

Water Inlet Valve, Aquastop & Flowmeter

Iberna IDI / Standard Wash System Dishwasher: Water fill timeout E2; flowmeter turbine pulse rate below threshold (<10 impulses per 100ml) during wash chamber filling.

On Iberna dishwashers featuring Standard Wash System hydraulic circuit, solenoid fill valve control, and heating element flow-through tube: Low line water pressure, scaled impeller in water jacket flowmeter, or defective reed switch sensor board.

Verify household water pressure (>1.5 bar). Inspect side air-break matrix for scale build-up. Test flowmeter reed switch continuity during active fill. Press and hold Start button for 5 seconds until buzzer sounds, close door to allow pump-out cycle to complete, then switch off.

E2

Hob / Cooktop

NTC Temperature Sensor & Thermistor

Iberna IH Touch Induction & Radiant Cooktop: Induction cooking zone coil overheat E2; NTC temperature sensor beneath ceramic glass detects temperature exceeding 240°C.

On Iberna cooktops utilizing IH Touch induction power converters, radiant coil zones, and touch-sensitive key lockout: Empty pot heated at booster setting (dry boil), thin warped pan base creating localized hot spot, or fan airflow blocked.

Switch off the cooking zone and remove cookware. Allow zone to cool down for 15 minutes. Check coil NTC thermistor resistance with a multimeter (~100 kΩ at 25°C). Verify bottom cabinetry intake air slots are not obstructed. Clear moisture from control area, power down circuit breaker for 40 seconds, restore power and touch Lock Key for 5 seconds.

E2

Refrigerator / Freezer

Refrigeration Compressor, Defrost Heater & PTC Relay

Iberna IR / Total FrostFree Combi Refrigerator: Freezer compartment temperature sensor malfunction E2; low-temperature NTC thermistor circuit open or short-circuited.

On Iberna refrigeration units featuring Total FrostFree air circulation evaporator, defrost termination bi-metal, and compressor start relay: Thermal fatigue under freezing cycles, moisture degradation in sensing tip, or severed freezer wire line.

Test freezer NTC resistance: nominal is ~5 kΩ at 25°C and ~32.5 kΩ at -18°C. Replace sensor assembly if open (>100 kΩ) or shorted (<500 Ω). Reset: Press and hold Fast Freeze button for 8 seconds until warning buzzer stops sounding, confirming internal microprocessor reset.

E2

Washing Machine

NTC Temperature Sensor & Thermistor

Iberna ILF / EcoTime Pro Inverter Washing Machine: Door / lid lock failure E2; machine does not engage lock solenoid or detects door open during cycle start.

On Iberna washers featuring reliable GIAS compact micro-controller, high-efficiency wash group, and fast-response NTC thermistors: Door catch out of alignment, defective door lock switch mechanism, or damaged wiring harness to main controller.

Inspect door strike hook. Verify door switch continuity with door closed. Replace door lock assembly if solenoid fails to latch. Move program selector to Stop, hold Start/Pause and Spin keys together for 5 seconds until status LEDs extinguish, then restart.

E03

Dishwasher

Drainage System & Drain Pump

Iberna IDI / Standard Wash System Dishwasher: Drain pump evacuation timeout E03; water remains detected in sump chamber after drain cycle timer elapses.

On Iberna dishwashers powered by Standard Wash System hydraulic circuit, solenoid fill valve control, and heating element flow-through tube: Toothpick or small bone jammed in pump impeller chamber, clogged corrugated drain hose, or worn pump motor (~160–220 Ω).

Remove sump filter cover and clear debris around drain impeller. Ensure hose is unobstructed to drain standpipe. Measure pump coil resistance (~160–220 Ω). Press and hold Start button for 5 seconds until buzzer sounds, close door to allow pump-out cycle to complete, then switch off.

E03

Tumble Dryer

NTC Temperature Sensor & Thermistor

Iberna ITD AirFlow Condenser Tumble Dryer: Maximum drying cycle time exceeded E03; machine aborts cycle after running for 210 minutes without laundry reaching target dryness.

On Iberna tumble dryers utilizing AirFlow condensation duct system, front/rear NTC temperature sensors, and capacitive run motor: Severely fouled condenser unit, weak heat-pump refrigerant pressure, or wet clothes spun at too low wash RPM (<800 RPM).

Always spin clothes at minimum 1000 RPM in washing machine. Thoroughly clean heat exchanger fins with soft brush. Verify compressor operating heat. Set selector to 0, hold Start/Pause and Half Heat buttons for 5 seconds until beep acknowledges memory wipe, then return to Off.

E03

Washing Machine

NTC Temperature Sensor & Thermistor

Iberna ILF / EcoTime Pro Inverter Washing Machine: Water evacuation fault E03; machine aborts cycle with water remaining in drum after 180 seconds of drain pump operation.

On Iberna washing machines featuring reliable GIAS compact micro-controller, high-efficiency wash group, and fast-response NTC thermistors: Blocked coin trap filter, foreign object jamming synchronous impeller, kinked drain hose, or open pump motor (~160–220 Ω).

Unscrew front coin filter and remove obstructions. Inspect impeller rotation. Measure drain pump winding resistance (~160–220 Ω). Move program selector to Stop, hold Start/Pause and Spin keys together for 5 seconds until status LEDs extinguish, then restart.

E3

Dishwasher

Drainage System & Drain Pump

Iberna IDI / Standard Wash System Dishwasher: Drain evacuation timeout E3; water remains in sump after 240 seconds of drain pump operation.

On Iberna dishwashers powered by Standard Wash System hydraulic circuit, solenoid fill valve control, and heating element flow-through tube: Blocked microfilter, foreign body (glass shard, olive pit) jamming drain impeller, kinked hose, or open pump motor (~160–220 Ω).

Remove sump filters and clean thoroughly. Check drain pump impeller for free rotation. Measure drain pump winding resistance (~160–220 Ω). Press and hold Start button for 5 seconds until buzzer sounds, close door to allow pump-out cycle to complete, then switch off.

E3

Hob / Cooktop

Drive Motor, Inverter & Tachometer Sensor

Iberna IH Touch Induction & Radiant Cooktop: Induction power board IGBT heatsink overtemperature E3; power transistor heatsink temperature exceeds 95°C safety shutoff.

On Iberna cooktops featuring IH Touch induction power converters, radiant coil zones, and touch-sensitive key lockout: Inoperative cooling fan, cutlery drawer or oven installed below hob blocking intake air, or dried thermal paste on heatsink.

Ensure minimum 20 mm air intake gap below hob and 5 mm frontal air exhaust gap. Test cooling fan spins freely and fan motor connector is plugged tight. Clear moisture from control area, power down circuit breaker for 40 seconds, restore power and touch Lock Key for 5 seconds.

E3

Refrigerator / Freezer

Refrigeration Compressor, Defrost Heater & PTC Relay

Iberna IR / Total FrostFree Combi Refrigerator: Evaporator defrost temperature sensor fault E3; defrost termination NTC thermistor out of calibrated ohmic range.

On Iberna refrigeration units featuring Total FrostFree air circulation evaporator, defrost termination bi-metal, and compressor start relay: Corrosion from defrost meltwater, loose mounting clip on accumulator tube, or internal resistor rupture.

Unclip defrost sensor from evaporator tubing. Check resistance (~5 kΩ at 25°C, ~16.3 kΩ at 0°C). Re-clip securely with thermal compound. Reset: Press and hold Fast Freeze button for 8 seconds until warning buzzer stops sounding, confirming internal microprocessor reset.

E3

Washing Machine

NTC Temperature Sensor & Thermistor

Iberna ILF / EcoTime Pro Inverter Washing Machine: Spin cycle unbalance alert E3; drum cannot distribute wet laundry load evenly to reach high spin speeds safely.

On Iberna washers utilizing reliable GIAS compact micro-controller, high-efficiency wash group, and fast-response NTC thermistors: Single heavy towel or bath rug, unevenly distributed bedding, or appliance chassis unlevel on floor.

Pause cycle, open door and manually untangle and redistribute garments. Check spirit level on top cover and adjust leveling feet. Move program selector to Stop, hold Start/Pause and Spin keys together for 5 seconds until status LEDs extinguish, then restart.

E04

Dishwasher

Drainage System & Drain Pump

Iberna IDI / Standard Wash System Dishwasher: Bottom tray anti-flood switch activated E04; water detected in base pan, triggering continuous drain and lock-out.

On Iberna dishwashers utilizing Standard Wash System hydraulic circuit, solenoid fill valve control, and heating element flow-through tube: Sump O-ring seal leak, perforated tub stainless steel seam, dripping wash pump shaft seal, or leaking water jacket hose.

Isolate electrical supply. Remove side panels and dry bottom pan. Run test cycle while inspecting sump joint, pump mechanical seal, and hose clamps with a torch. Press and hold Start button for 5 seconds until buzzer sounds, close door to allow pump-out cycle to complete, then switch off.

E04

Tumble Dryer

NTC Temperature Sensor & Thermistor

Iberna ITD AirFlow Condenser Tumble Dryer: Heating circuit safety lockout E04; heater relay contacts stuck closed, or high-limit safety thermostat tripped.

On Iberna tumble dryers powered by AirFlow condensation duct system, front/rear NTC temperature sensors, and capacitive run motor: Welded relay contacts on control board, open safety thermal cutout fuse, or burned heating coil (~20–40 Ω).

Disconnect heater leads and measure element resistance (~20–40 Ω). Test safety thermostat continuity. Inspect board relay for welded contacts. Set selector to 0, hold Start/Pause and Half Heat buttons for 5 seconds until beep acknowledges memory wipe, then return to Off.

← Previous Page

Page 1 of 6 (165 results)Next Page →

Iberna — Complete Error Code Catalog

77 Verified Error Codes

Server-side index of all verified manufacturer error codes for technicians and automated crawlers.

Dishwasher30

AL03 AL05 E01 E1 E02 E2 E03 E3 E04 E4 E05 E5 E06 E6 E07 E7 E08 E8 E9 E10 E12 E14 E15 E16 E17 E18 Ed EF Eh EL

Washing Machine8

CLr E20 E22 FA FC0 FC1 FC2 Unb

Tumble Dryer10

E09 E11 E13 E21 F1 F2 F3 F4 F5 F6

Oven / Microwave19

Er01 Er02 Er03 Er04 Er05 Er06 Er07 Er08 Er09 Er15 Er20 Er21 Er22 Er31 Er36 Er47 Er56 Loc Sabb

Hob / Cooktop6

E0 F0 F7 F8 F9 U

Refrigerator / Freezer4

AL01 AL02 EA Er

Need Help? Call a Certified Technician

Our official certified partners service Iberna appliances in your area.

Electroassistance (Switzerland)Appliance Care UK (United Kingdom)

CodesErreur.com

Premium appliance diagnostics & repair database.
Powered by AI to help certified technicians worldwide.

Trusted by professionals in CH & FR

Platform

Search Database PRO Diagnostic AIPRO Diagnostic Tools Brands

Workshop Tools

Brands (87)OEM Manuals Find Rating Plate Parts Locator

For Technicians

Specialists Technician Forum Tech Jobs Premium

Corporate

Terms of Service Privacy PolicyOfficial Swiss Repair Partner: Electroassistance

OPERATIONAL SAFETY SPECIFICATION

SAFETY DISCLAIMER

The technical information, diagnostic guides, error codes, and AI-generated suggestions provided on this website are intended exclusively for certified and qualified professionals. Appliance repair involves severe electrical hazards, high voltages, and mechanical risks that can result in fatal injury or severe property damage. If you are not a trained technician, do not attempt to repair any appliances. CodesErreur assumes no responsibility or liability for any damage, injury, or consequential losses resulting from the use of the information provided on this platform. You use all information entirely at your own risk.

© 2026 CodesErreur. All rights reserved.

Official Swiss Repair Partner: Electroassistance Terms of Service Privacy Policy