Skip to content
CodesErreur.comSWISS PRO ENGINE
Core Diagnostics
DiagnosticsBrandsOEM ManualsSpecialistsAI EngineerPRO
Workshop Tools
Diagnostic ToolsNEW
Hardware interfaces & test probes
Find Rating Plate
Locate exact E-Nr, PNC & serial codes
Parts Locator
Global OEM spare parts suppliers
Community & Career
Academy & Courses
Masterclasses by senior technicians
Certification ExamsPRO
Verify your B2B technical credentials
Elite Forum
Peer-to-peer field troubleshooting
Tech Jobs
B2B recruitment & field opportunities
Leaderboard
Global ranking of verified specialists
Certified Appliance Engineering EcosystemApply for Certification →
Language Selector
Account & Access
Upgrade PRO
Back to Search
OEM VERIFIED BENCH
OFFICIAL FAULT CODEF60
Miele
Miele // OFFICIAL DIAGNOSTIC BENCH

Miele F60

Washing MachineNTC Temperature Sensor & Thermistor
Luxury front-loading washing machine in brushed titanium with illuminated dark glass drum
Washing Machine
Select Appliance Type
0ms Instant Telemetry Switch

Symptom / Description

FAULT

The device signals an overheating condition and stops operation mid-cycle.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

The temperature sensor (NTC) located on the power board has detected excessive heat, due to inadequate ventilation or a failure of the sensor itself.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED
1Unplug the device. Make sure the ventilation slots are not blocked. Measure the resistance of the NTC sensor on the electronic board. If the value is out of specification or if the ventilation is functional, replacement of the power board is required.
AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time
AI WORKSHOP PROTOCOL ENGINE
Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH
Need Help? Call a Certified TechnicianWorldwide Miele Parts Finder
Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLNTC Temperature Sensor & ThermistorWashing Machine
2. Multimeter & Electrical Bench Tests (Ω)
MODE: OHMMETER (Ω)AUTO-RANGE
Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board
CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)
Nominal Resistance (Ω)
4.8kΩ–12kΩ (at 20°C–25°C)NOMINAL
0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)
▲ NOMINAL OPERATING WINDOW
Target Component:NTC Temperature Sensor Probe (Thermistor)
Test Pins & Connections
PROBE (+)
PROBE (-)
Across sensor pins 1-2 (unplugged harness)
Tolerance & Diagnostic CriteriaNegative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit.
1. Pre-Intervention Electrical Safety Protocols
  • !Electrical Safety Protocol: Disconnect 230V electrical mains power before removing appliance side or rear panels.
  • !Ensure tub water or heating chamber has cooled below 30°C before unclipping thermistor probe.
  • !Use CAT III 600V/1000V insulated test probes when tng at PCB edge connectors.
3. Preliminary Mechanical & Visual Checks
  • Inspect sensor immersion sleeve for calcification, limescale scale, or thermal paste degradation.
  • Check wiring harness for pinch points, chafing against chassis metal, and terminal pin oxidation.
  • Verify probe is firmly seated in its rubber grommet or bracket inside the water/air circuit.
Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Miele F60

FAQ TREE
What does error code F60 mean on a Miele appliance?

Miele error code F60 indicates: The device signals an overheating condition and stops operation mid-cycle..

What is the root cause of Miele error code F60?

The primary root cause for Miele code F60 is: The temperature sensor (NTC) located on the power board has detected excessive heat, due to inadequate ventilation or a failure of the sensor itself..

How do I fix or resolve Miele error code F60?

To resolve error code F60: Unplug the device. Make sure the ventilation slots are not blocked. Measure the resistance of the NTC sensor on the electronic board. If the value is out of specification or if the ventilation is functional, replacement of the power board is required.

Is it safe to clear Miele error code F60 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Miele code F60 persists, the physical component causing The temperature sensor (NTC) located on the power board has detected excessive heat, due to inadequate ventilation or a failure of the sensor itself. must be inspected or replaced.

How do I test electrical resistance for Miele code F60 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test NTC Temperature Sensor Probe (Thermistor) across Across sensor pins 1-2 (unplugged harness). Expected nominal reading is 4.8kΩ–12kΩ (at 20°C–25°C). Tolerance: Negative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit..

What safety protocol must be followed before servicing Miele code F60?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

SEMANTIC KNOWLEDGE GRAPH // MIELE

Related Miele Washing Machine Error Codes

Diagnostic Link Mesh14 OEM Cross-References

Cross-referenced diagnostic codes for technicians inspecting similar component subsystems.

F6000Electronic Control Board (PCB) & Bus Communications
Unable to select cooking zone 1, or the 'Hold' function and cooking assistant for this zone ...
Inspect Protocol
F6001General System & Mechanical Integration
Adjusting the power of cooking zone 1 via the touch button (-) is ineffective.
Inspect Protocol
F6002General System & Mechanical Integration
It is not possible to increase the power of cooking zone 1 using the (+) button.
Inspect Protocol
F6003Electronic Control Board (PCB) & Bus Communications
The Booster function or the special cooking function (ZZ) for cooking zone 1 cannot be activ...
Inspect Protocol
F6004Electronic Control Board (PCB) & Bus Communications
Selection of cooking zone 2 is impossible, and the associated functions (Hold, assistant) do...
Inspect Protocol
F6005Electronic Control Board (PCB) & Bus Communications
The power of cooking zone 2 cannot be reduced using the (-) button.
Inspect Protocol
F6006General System & Mechanical Integration
Increasing the power on cooking zone 2 using the (+) button does not work.
Inspect Protocol
F6007General System & Mechanical Integration
The Booster or special cooking (ZZ) functions are inaccessible for cooking zone 2.
Inspect Protocol
F6008Electronic Control Board (PCB) & Bus Communications
Cooking zone 5 cannot be selected, or its 'Hold'/assistant functions do not work.
Inspect Protocol
F6009General System & Mechanical Integration
It is impossible to lower the power of cooking zone 5 using the (-) button.
Inspect Protocol
F6010General System & Mechanical Integration
The (+) button does not work to increase the power of cooking zone 5.
Inspect Protocol
F6011General System & Mechanical Integration
Activation of Booster mode or the special function (ZZ) is not possible for cooking zone 5.
Inspect Protocol
F6012Electronic Control Board (PCB) & Bus Communications
Cooking zone 3 does not respond to selection, does not maintain temperature, or the cooking ...
Inspect Protocol
F6013Electronic Control Board (PCB) & Bus Communications
It is impossible to reduce the power of cooking zone 3 using the 'minus' touch button.
Inspect Protocol
CodesErreur.com

Premium appliance diagnostics & repair database.
Powered by AI to help certified technicians worldwide.

Trusted by professionals in CH & FR

Platform

Search DatabasePRO Diagnostic AIPRODiagnostic ToolsBrands

Workshop Tools

Brands (87)OEM ManualsFind Rating PlateParts Locator

For Technicians

SpecialistsTechnician ForumTech JobsPremium

Corporate

Terms of ServicePrivacy PolicyOfficial Swiss Repair Partner: Electroassistance
OPERATIONAL SAFETY SPECIFICATION

SAFETY DISCLAIMER

The technical information, diagnostic guides, error codes, and AI-generated suggestions provided on this website are intended exclusively for certified and qualified professionals. Appliance repair involves severe electrical hazards, high voltages, and mechanical risks that can result in fatal injury or severe property damage. If you are not a trained technician, do not attempt to repair any appliances. CodesErreur assumes no responsibility or liability for any damage, injury, or consequential losses resulting from the use of the information provided on this platform. You use all information entirely at your own risk.

© 2026 CodesErreur. All rights reserved.

Official Swiss Repair Partner: Electroassistance Terms of Service Privacy Policy