OEM VERIFIED BENCH

OFFICIAL FAULT CODEd01

Ocean // OFFICIAL DIAGNOSTIC BENCH

Ocean d01

Washing MachineWater Inlet Valve, Aquastop & Flowmeter

Washing Machine

Other Brands Sharing Code d01:BrandtD01 De DietrichD01 FAGORD01 SauterD01

Symptom / Description

FAULT

Machine won't fill with water.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

Water tap is closed, inlet hose is kinked or blocked, or the water inlet valve has failed.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Ensure water supply is on and the hose is not bent. Check and clean the filter in the inlet valve. If the issue persists, test and replace the water inlet valve.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Ocean Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLWater Inlet Valve, Aquastop & FlowmeterWashing Machine

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

3.5kΩ–4.5kΩ (Standard 230V) / 2.0kΩ–4.2kΩ (Aquastop)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Solenoid Valve Coil / Aquastop Pneumatic Valve

Test Pins & Connections

PROBE (+)

PROBE (-)

Across coil spade terminals (disconnect harness first)

Tolerance & Diagnostic Criteria±10%. Open circuit (OL) indicates burned solenoid coil. Flowmeter turbine reed switch pulses on flow.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Disconnect electrical power before touching solenoid valve coils or Aquastop connectors.
!Firmly shut off the domc water supply tap before unscrewing the inlet hose fitting.
!Check safety base drip tray for accumulated water triggering the anti-flood polystyrene float switch.

3. Preliminary Mechanical & Visual Checks

Remove and clean sediment and sand particles from the 3/4" inlet hose metal mesh filter.
Verify domestic dynamic water pressure is between 1.0 and 10.0 bar (0.1 to 1.0 MPa).
Inspect outer Aquastop hose jacket for expansion, pinch damage, or internal leak reservoir triggering.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Ocean D01

FAQ TREE

What does error code D01 mean on a Ocean appliance?

Ocean error code D01 indicates: Machine won't fill with water..

What is the root cause of Ocean error code D01?

The primary root cause for Ocean code D01 is: Water tap is closed, inlet hose is kinked or blocked, or the water inlet valve has failed..

How do I fix or resolve Ocean error code D01?

To resolve error code D01: Ensure water supply is on and the hose is not bent. Check and clean the filter in the inlet valve. If the issue persists, test and replace the water inlet valve.

Is it safe to clear Ocean error code D01 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Ocean code D01 persists, the physical component causing Water tap is closed, inlet hose is kinked or blocked, or the water inlet valve has failed. must be inspected or replaced.

How do I test electrical resistance for Ocean code D01 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Solenoid Valve Coil / Aquastop Pneumatic Valve across Across coil spade terminals (disconnect harness first). Expected nominal reading is 3.5kΩ–4.5kΩ (Standard 230V) / 2.0kΩ–4.2kΩ (Aquastop). Tolerance: ±10%. Open circuit (OL) indicates burned solenoid coil. Flowmeter turbine reed switch pulses on flow..

What safety protocol must be followed before servicing Ocean code D01?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEd01

Ocean // OFFICIAL DIAGNOSTIC BENCH

Ocean d01

Washing MachineWater Inlet Valve, Aquastop & Flowmeter

Washing Machine

Other Brands Sharing Code d01:BrandtD01 De DietrichD01 FAGORD01 SauterD01

Symptom / Description

FAULT

Machine won't fill with water.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

Water tap is closed, inlet hose is kinked or blocked, or the water inlet valve has failed.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Ensure water supply is on and the hose is not bent. Check and clean the filter in the inlet valve. If the issue persists, test and replace the water inlet valve.

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Ocean Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLWater Inlet Valve, Aquastop & FlowmeterWashing Machine

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

3.5kΩ–4.5kΩ (Standard 230V) / 2.0kΩ–4.2kΩ (Aquastop)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Solenoid Valve Coil / Aquastop Pneumatic Valve

Test Pins & Connections

PROBE (+)

PROBE (-)

Across coil spade terminals (disconnect harness first)

Tolerance & Diagnostic Criteria±10%. Open circuit (OL) indicates burned solenoid coil. Flowmeter turbine reed switch pulses on flow.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Disconnect electrical power before touching solenoid valve coils or Aquastop connectors.
!Firmly shut off the domc water supply tap before unscrewing the inlet hose fitting.
!Check safety base drip tray for accumulated water triggering the anti-flood polystyrene float switch.

3. Preliminary Mechanical & Visual Checks

Remove and clean sediment and sand particles from the 3/4" inlet hose metal mesh filter.
Verify domestic dynamic water pressure is between 1.0 and 10.0 bar (0.1 to 1.0 MPa).
Inspect outer Aquastop hose jacket for expansion, pinch damage, or internal leak reservoir triggering.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Ocean D01

FAQ TREE

What does error code D01 mean on a Ocean appliance?

Ocean error code D01 indicates: Machine won't fill with water..

What is the root cause of Ocean error code D01?

The primary root cause for Ocean code D01 is: Water tap is closed, inlet hose is kinked or blocked, or the water inlet valve has failed..

How do I fix or resolve Ocean error code D01?

To resolve error code D01: Ensure water supply is on and the hose is not bent. Check and clean the filter in the inlet valve. If the issue persists, test and replace the water inlet valve.

Is it safe to clear Ocean error code D01 by resetting power?

How do I test electrical resistance for Ocean code D01 using a multimeter?

What safety protocol must be followed before servicing Ocean code D01?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Ocean d01

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Ocean D01

Community Verification

Related Ocean Washing Machine Error Codes

Ocean d01

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Ocean D01

Community Verification

Related Ocean Washing Machine Error Codes