Scholtès Refrigerator / Freezer F3E3

Scholtès error code F3E3 indicates: Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code F3E3 indicates in-door ice box compartment thermistor failure; ice production halts or ice maker overheats..

The primary root cause for Scholtès code F3E3 is: On Scholtès refrigerators (Scholtès Haute Horlogerie Culinaire sensors and micro-electronic platform architecture): Open circuit in ice box NTC probe or broken wire in French-door hinge harness. Calibration: 2.7 kΩ at 25°C, 14.5 kΩ at -10°C..

To resolve error code F3E3: Disconnect power. Remove ice storage bucket and sensor cover. Measure resistance with digital meter: nominal is 13.5–15.5 kΩ at ice-making temperature (-10°C). Replace ice box sensor harness assembly. Press and hold Alarm Reset pad for 5 seconds, verify compartment display stops blinking, and allow 12h for complete stabilization.

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Scholtès code F3E3 persists, the physical component causing On Scholtès refrigerators (Scholtès Haute Horlogerie Culinaire sensors and micro-electronic platform architecture): Open circuit in ice box NTC probe or broken wire in French-door hinge harness. Calibration: 2.7 kΩ at 25°C, 14.5 kΩ at -10°C. must be inspected or replaced.

Set a digital multimeter to ohms (Ω). Disconnect power and test NTC Temperature Sensor Probe (Thermistor) across Across sensor pins 1-2 (unplugged harness). Expected nominal reading is 4.8kΩ–12kΩ (at 20°C–25°C). Tolerance: Negative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit..

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Scholtès error code F3E3 on a Refrigerator / Freezer indicates: Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code F3E3 indicates in-door ice box compartment thermistor failure; ice production halts or ice maker overheats.. Primary cause: On Scholtès refrigerators (Scholtès Haute Horlogerie Culinaire sensors and micro-electronic platform architecture): Open circuit in ice box NTC probe or broken wire in French-door hinge harness. Calibration: 2.7 kΩ at 25°C, 14.5 kΩ at -10°C.. Recommended solution: Disconnect power. Remove ice storage bucket and sensor cover. Measure resistance with digital meter: nominal is 13.5–15.5 kΩ at ice-making temperature (-10°C). Replace ice box sensor harness assembly. Press and hold Alarm Reset pad for 5 seconds, verify compartment display stops blinking, and allow 12h for complete stabilization..

Scholtès error code F3E3 on a Dishwasher indicates: Scholtès Supreme Inox & Touch-Control Dishwasher: Wash water heating fault F3 E3; control board detects no temperature rise after 30 minutes of continuous wash operation.. Primary cause: On Scholtès dishwashers (Scholtès Haute Horlogerie Culinaire sensors and micro-electronic platform architecture): Open calrod heating element, tripped high-limit safety thermostat on tub underside, or defective heater control relay on main board.. Recommended solution: Disconnect power. Measure heating element resistance with multimeter: nominal 10–30 Ω (typically 12–18 Ω). Check high-limit thermostat continuity (<0.5 Ω). Hold Start/Cancel pad for 5 seconds until drain initiates, allow 60s, then cycle mains power..