Whirlpool Refrigerator / Freezer F3E3

Whirlpool error code F3E3 indicates: Whirlpool 6th Sense Dual-Cool & Total NoFrost Refrigerator: Diagnostic code F3E3 indicates in-door ice box compartment thermistor failure; ice production halts or ice maker overheats..

The primary root cause for Whirlpool code F3E3 is: On Whirlpool refrigerators (Whirlpool 6th Sense algorithms and WAVE / L1373 electronic platform): Open circuit in ice box NTC probe or broken wire in French-door hinge harness. Calibration: 2.7 kΩ at 25°C, 14.5 kΩ at -10°C..

To resolve error code F3E3: Disconnect power. Remove ice storage bucket and sensor cover. Measure resistance with digital meter: nominal is 13.5–15.5 kΩ at ice-making temperature (-10°C). Replace ice box sensor harness assembly. Press and hold the Filter Reset or Alarm Silence touch pad for 5 seconds until the confirmation chime sounds.

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Whirlpool code F3E3 persists, the physical component causing On Whirlpool refrigerators (Whirlpool 6th Sense algorithms and WAVE / L1373 electronic platform): Open circuit in ice box NTC probe or broken wire in French-door hinge harness. Calibration: 2.7 kΩ at 25°C, 14.5 kΩ at -10°C. must be inspected or replaced.

Set a digital multimeter to ohms (Ω). Disconnect power and test NTC Temperature Sensor Probe (Thermistor) across Across sensor pins 1-2 (unplugged harness). Expected nominal reading is 4.8kΩ–12kΩ (at 20°C–25°C). Tolerance: Negative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit..

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Whirlpool error code F3E3 on a Refrigerator / Freezer indicates: Whirlpool 6th Sense Dual-Cool & Total NoFrost Refrigerator: Diagnostic code F3E3 indicates in-door ice box compartment thermistor failure; ice production halts or ice maker overheats.. Primary cause: On Whirlpool refrigerators (Whirlpool 6th Sense algorithms and WAVE / L1373 electronic platform): Open circuit in ice box NTC probe or broken wire in French-door hinge harness. Calibration: 2.7 kΩ at 25°C, 14.5 kΩ at -10°C.. Recommended solution: Disconnect power. Remove ice storage bucket and sensor cover. Measure resistance with digital meter: nominal is 13.5–15.5 kΩ at ice-making temperature (-10°C). Replace ice box sensor harness assembly. Press and hold the Filter Reset or Alarm Silence touch pad for 5 seconds until the confirmation chime sounds..

Whirlpool error code F3E3 on a Dishwasher indicates: Whirlpool 6th Sense PowerClean Pro & MaxiSpace Dishwasher: Wash water heating fault F3 E3; control board detects no temperature rise after 30 minutes of continuous wash operation.. Primary cause: On Whirlpool dishwashers (Whirlpool 6th Sense algorithms and WAVE / L1373 electronic platform): Open calrod heating element, tripped high-limit safety thermostat on tub underside, or defective heater control relay on main board.. Recommended solution: Disconnect power. Measure heating element resistance with multimeter: nominal 10–30 Ω (typically 12–18 Ω). Check high-limit thermostat continuity (<0.5 Ω). Press and hold Start/Resume or Cancel pad for 5 seconds to initiate 60s drain, then turn off power breaker..

Whirlpool error code F3E3 on a Oven indicates: Whirlpool 6th Sense W Collection Pyrolytic Built-in Oven: Meat probe temperature sensor shorted or out of range F3 E3; probe cooking mode shuts down or temperature reads erratically.. Primary cause: On Whirlpool ovens (Whirlpool 6th Sense algorithms and WAVE / L1373 electronic platform): Water or grease entered probe handle seam during washing, or twisted internal probe cable shorted positive lead to ground shield.. Recommended solution: Unplug probe from interior jack. Measure probe resistance with multimeter across tip and sleeve: nominal 50–100 kΩ at 25°C (77°F). Replace probe if <1 kΩ or open. Turn temperature knob to 0, hold Clock/Timer pad for 5 seconds, disconnect electrical breaker for 60 seconds..