Access our premium database of error codes, common faults, and professional repair solutions for Beko appliances.
Freezer temperature sensor fault
The freezer compartment's temperature sensor (thermistor) has failed or its wiring is damaged.
Test the sensor for the correct resistance values at various temperatures. Check wiring harness. Replace the sensor if faulty.
Beko E1: Cooling circuit or defrost system anomaly in Refrigerator / Freezer; compartment temperature deviation.
The defrost sensor, located on the evaporator coil, has failed.
Access the evaporator panel inside the freezer. Test the defrost sensor and replace it if it's open or short-circuited.
Beko E2: Water/air heating failure in Washing Machine; heating circuit does not reach set temperature.
The heating element is not working or has failed.
Test the heating element for continuity using a multimeter and replace if necessary. Check wiring.
Refrigerator temperature sensor fault
The fresh food compartment's temperature sensor has failed or has a bad connection.
Locate and test the refrigerator compartment sensor. Check wiring and replace the sensor if necessary.
Beko E4: Cooling circuit or defrost system anomaly in Refrigerator / Freezer; compartment temperature deviation.
The defrost heating element is not working, which leads to excessive ice buildup on the evaporator coils.
Manually defrost the unit. Test the defrost heater for continuity. Also check the defrost thermal fuse. Replace faulty components.
Beko E5: Water drainage failure detected in Washing Machine; drain pump cannot evacuate water within safety time limit.
The drain filter is clogged, the drain pump is faulty, or the drain hose is blocked/kinked.
Clean the drain pump filter. Check the pump and hose for blockages. Replace the pump if it's humming but not turning.
Beko E6: Motor drive or inverter rotation anomaly in Washing Machine; drum/motor fails to spin at target RPM.
Motor is not turning. Most commonly caused by worn motor carbon brushes.
Check and replace motor carbon brushes if they are worn down. Inspect motor and wiring.
Beko E9: Operational cycle fault detected during Refrigerator / Freezer program execution.
The automatic ice maker mechanism has failed or is jammed.
Check for jammed ice cubes. Ensure water supply to the ice maker is working. Test the ice maker module and replace if faulty.
Beko E17: Operational cycle fault detected during Washing Machine program execution.
Too much detergent has been used, or a non-HE detergent was used in a high-efficiency machine.
Run a rinse and spin cycle to clear the foam. Use the correct type and amount of detergent in future washes.
Beko E18: Door lock safety interlock fault in Washing Machine; door switch contact fails to close or open.
The laundry inside the drum is not distributed evenly, causing excessive vibration during the spin cycle.
Stop the machine, open the door, and redistribute the laundry more evenly. Restart the cycle.
Oven overheating / NTC sensor fault
The oven's NTC temperature sensor has failed in an open-circuit state.
Disconnect power from the oven. Test the resistance of the temperature sensor probe and replace it if faulty.
Beko F3: NTC temperature sensor signal out of range (open or short circuit) in Oven / Microwave.
The NTC sensor reading is too high, the cooling fan has failed, or the sensor itself is faulty.
Check that the cooling fan is operational. Test and replace the NTC temperature sensor.
Door lock error during self-clean
The door lock mechanism has failed to engage or disengage for the pyrolytic cleaning cycle.
Turn the power off and on to reset. Check the door lock mechanism for jamming or electrical failure. Replace lock assembly.
Door lock mechanism error
The door lock motor is disconnected, jammed, or has failed electrically.
Check the wiring to the door lock motor. Inspect the mechanism for physical blockages. Replace the door lock assembly.
Beko H1: Water drainage failure detected in Dishwasher; drain pump cannot evacuate water within safety time limit.
Water has collected in the base of the machine, activating the anti-flood float switch.
Disconnect power. Tilt the machine to drain the base. Find and repair the source of the leak (hoses, seals, pump housing).
Beko H2: Water inlet / filling timeout in Dishwasher; appliance fails to fill to minimum operational level.
The dishwasher is not filling with water due to a faulty inlet valve, kinked hose, or no water supply.
Ensure the water supply is on. Inspect the inlet hose. Test and replace the water inlet valve if it's not opening.
Beko H4: NTC temperature sensor signal out of range (open or short circuit) in Dishwasher.
A fault with the main heating element or the NTC temperature sensor.
Test the heating element and NTC sensor for continuity and correct resistance. Replace the faulty component.
Beko H5: Water drainage failure detected in Dishwasher; drain pump cannot evacuate water within safety time limit.
The dishwasher is not draining due to blocked filters, a faulty drain pump, or a blocked drain hose.
Clean all filters in the base of the dishwasher. Check the drain hose for blockages. Inspect and test the drain pump.
Beko H6: NTC temperature sensor signal out of range (open or short circuit) in Dishwasher.
The NTC (temperature sensor) has an open or short circuit.
Check the wiring to the NTC sensor. Test the sensor's resistance and replace it if the reading is incorrect.
Our official certified partners service Beko appliances in your area.