Access our premium database of error codes, common faults, and professional repair solutions for Gea-Appliances appliances.
Pump out failure during drain
The dishwasher failed to drain within the allotted time. This is often caused by a clog in the drain system.
Check and clean the dishwasher's filter assembly. Inspect the drain hose for blockages. Run the garbage disposal to clear the drain.
Check controls or stuck button
A button on the dispenser control panel has been pressed and held for too long, or is stuck.
Try pressing each button on the control panel to release the stuck key. If the error code does not clear, the dispenser control board may need to be replaced.
Gea-Appliances DE: Cooling circuit or defrost system anomaly in Refrigerator / Freezer; compartment temperature deviation.
The automatic defrost system has malfunctioned. This could be due to a failed defrost heater, defrost thermostat, or main control board.
This error requires diagnosis by a technician. Manually defrost the freezer to restore cooling temporarily, but the underlying component will need to be tested and replaced.
Gea-Appliances E22: Water inlet / filling timeout in Washing Machine; appliance fails to fill to minimum operational level.
Water is not entering the machine, or is entering too slowly. This could be due to closed water faucets, kinked hoses, or clogged inlet valve screens.
Ensure both hot and cold water faucets are fully open. Check hoses for kinks. Turn off water, disconnect hoses, and clean the filter screens inside the water inlet valve.
Gea-Appliances E30: Water drainage failure detected in Washing Machine; drain pump cannot evacuate water within safety time limit.
The drain pump filter is clogged, the drain hose is blocked or kinked, or the drain pump has failed.
Unplug the washer. Locate and clean the drain pump filter. Check the drain hose for any kinks or blockages. If the problem persists, the drain pump may need to be replaced.
Gea-Appliances E40: Door lock safety interlock fault in Washing Machine; door switch contact fails to close or open.
The lid is not closed and locked properly, or the lid lock switch assembly is faulty.
Ensure the lid is fully closed and there are no obstructions. If the error continues, the lid lock assembly likely needs to be tested and replaced.
Freezer temperature sensor error
The freezer thermistor (temperature sensor) has failed or is providing an out-of-range reading to the control board.
The freezer thermistor needs to be tested with a multimeter. If it's faulty, it must be replaced to ensure proper temperature regulation.
Refrigerator temperature sensor error
The fresh food compartment thermistor (temperature sensor) has failed.
The refrigerator thermistor needs to be tested and likely replaced. Its failure prevents the refrigerator from maintaining the correct temperature.
Gea-Appliances F1: NTC temperature sensor signal out of range (open or short circuit) in Oven / Microwave.
The oven control board detects that the oven is overheating. This is often caused by a faulty control board or a failed oven temperature sensor.
Disconnect power to the oven. This error typically requires professional service to test and replace the electronic control board or the temperature sensor.
Oven temperature is too high
The oven has exceeded a preset high-temperature limit, often due to a shorted oven temperature sensor or a faulty control board relay.
Turn off power at the circuit breaker for 5 minutes, then restore power. If the code returns, the oven temperature sensor likely needs to be replaced.
Open oven temperature sensor circuit
The control board is not detecting the oven temperature sensor. This indicates a failed sensor or a break in the wiring.
Disconnect power. Check the wiring connection between the temperature sensor and the control board. If wiring is intact, replace the oven temperature sensor.
Stuck key on control panel
A button on the touchpad is shorted or stuck in the pressed position.
Try cleaning the touchpad with a soft, damp cloth. Disconnecting power for 5 minutes can sometimes reset it. If the error persists, the control panel assembly needs to be replaced.
Door lock circuit failure
There is a problem with the motorized door lock assembly used for the self-clean cycle.
Disconnect power. Check the wiring to the door lock assembly. The door lock motor or switch assembly may have failed and needs replacement.
Freezer fan motor failure
The control board has detected that the freezer evaporator fan motor is not running. This can be caused by ice buildup blocking the fan, or a failed motor.
Check for ice or frost obstructing the fan blades. If clear, the fan motor or its wiring is likely faulty and requires replacement.
Ftd error code on display, indicating a defrost system failure.
Water is not draining from the dishwasher tub due to a clogged filter, blocked drain hose, or a faulty drain pump.
Power cycle unit. If error persists, test defrost system components (heater, terminator, thermistor) with a multimeter and replace the faulty part. If all components are good, replace the main control board.
No water or low water detected
The dishwasher is not filling with water. The water supply valve may be closed, the water line kinked, or the water inlet valve has failed.
Verify the hot water supply valve under the sink is fully open. Check the water supply line for any kinks. If the issue persists, the water inlet valve may need replacement.
Leak detected in base pan
The dishwasher has detected water in the base pan underneath the tub, indicating a leak or an over-sudsing condition.
Turn off power and water to the dishwasher. Check for obvious leaks from hoses or the pump. Using too much or the wrong type of detergent can also cause over-sudsing.
Gea-Appliances PF: Operational cycle fault detected during Dishwasher program execution.
A power outage or interruption occurred during a cycle.
Press the Start button to resume the cycle where it left off. Or, press Start then Cancel to clear the cycle and begin a new one. For refrigerators, this code clears after a button is pressed.
Gea-Appliances UE: Operational cycle fault detected during Washing Machine program execution.
The laundry load is unbalanced, causing the drum to wobble excessively during the spin cycle.
Pause the cycle and redistribute the clothes evenly inside the drum. Remove heavy, waterlogged items or add a few towels to balance the load. Restart the spin cycle.
Power failure or communication error
Indicates a recent power failure or a communication issue between the main control board and the display board.
Attempt a reset by unplugging the refrigerator or turning it off at the circuit breaker for 5 minutes. If the code reappears, it may indicate a control board issue.