Skip to content
CodesErreur.comSWISS PRO ENGINE
Core Diagnostics
DiagnosticsBrandsOEM ManualsSpecialistsAI EngineerPRO
Workshop Tools
Diagnostic ToolsNEW
Hardware interfaces & test probes
Find Rating Plate
Locate exact E-Nr, PNC & serial codes
Parts Locator
Global OEM spare parts suppliers
Community & Career
Academy & Courses
Masterclasses by senior technicians
Certification ExamsPRO
Verify your B2B technical credentials
Elite Forum
Peer-to-peer field troubleshooting
Tech Jobs
B2B recruitment & field opportunities
Leaderboard
Global ranking of verified specialists
Certified Appliance Engineering EcosystemApply for Certification →
Language Selector
Account & Access
Upgrade PRO
Back to Search
OEM VERIFIED BENCH
OFFICIAL FAULT CODE8
Bosch
Bosch // OFFICIAL DIAGNOSTIC BENCH

Bosch 8

DishwasherNTC Temperature Sensor & Thermistor
Premium built-in dishwasher with open illuminated stainless steel interior and precision spray arms
Dishwasher

Symptom / Description

FAULT

Fault detected in the NTC temperature sensor circuit

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

Defective NTC Temperature Sensor Probe (Thermistor), open/short circuit in the wiring harness, or faulty connector on the ntc temperature sensor & thermistor.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED
1Disconnect 230V mains power. 2. Unplug NTC thermistor harness connector. 3. Measure NTC resistance with multimeter across pins 1-2 (nominal: 4.8kΩ–12kΩ at 20°C–25°C; resistance should drop smoothly when probe tip is warmed). Replace sensor if open circuit (OL). 4. Reset: Press and hold Start/Reset for 3 to 5 seconds until display shows 0:01. Turn dial to OFF, wait 15 seconds, turn back ON and run rinse cycle.
AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time
AI WORKSHOP PROTOCOL ENGINE
Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH
Need Help? Call a Certified TechnicianWorldwide Bosch Parts Finder
Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLNTC Temperature Sensor & ThermistorDishwasher
2. Multimeter & Electrical Bench Tests (Ω)
MODE: OHMMETER (Ω)AUTO-RANGE
Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board
CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)
Nominal Resistance (Ω)
4.8kΩ–12kΩ (at 20°C–25°C)NOMINAL
0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)
▲ NOMINAL OPERATING WINDOW
Target Component:NTC Temperature Sensor Probe (Thermistor)
Test Pins & Connections
PROBE (+)
PROBE (-)
Across sensor pins 1-2 (unplugged harness)
Tolerance & Diagnostic CriteriaNegative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit.
1. Pre-Intervention Electrical Safety Protocols
  • !Electrical Safety Protocol: Disconnect 230V electrical mains power before removing appliance side or rear panels.
  • !Ensure tub water or heating chamber has cooled below 30°C before unclipping thermistor probe.
  • !Use CAT III 600V/1000V insulated test probes when tng at PCB edge connectors.
3. Preliminary Mechanical & Visual Checks
  • Inspect sensor immersion sleeve for calcification, limescale scale, or thermal paste degradation.
  • Check wiring harness for pinch points, chafing against chassis metal, and terminal pin oxidation.
  • Verify probe is firmly seated in its rubber grommet or bracket inside the water/air circuit.
Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Bosch 8

FAQ TREE
What does error code 8 mean on a Bosch appliance?

Bosch error code 8 indicates: Fault detected in the NTC temperature sensor circuit.

What is the root cause of Bosch error code 8?

The primary root cause for Bosch code 8 is: Defective NTC Temperature Sensor Probe (Thermistor), open/short circuit in the wiring harness, or faulty connector on the ntc temperature sensor & thermistor..

How do I fix or resolve Bosch error code 8?

To resolve error code 8: 1. Disconnect 230V mains power. 2. Unplug NTC thermistor harness connector. 3. Measure NTC resistance with multimeter across pins 1-2 (nominal: 4.8kΩ–12kΩ at 20°C–25°C; resistance should drop smoothly when probe tip is warmed). Replace sensor if open circuit (OL). 4. Reset: Press and hold Start/Reset for 3 to 5 seconds until display shows 0:01. Turn dial to OFF, wait 15 seconds, turn back ON and run rinse cycle.

Is it safe to clear Bosch error code 8 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Bosch code 8 persists, the physical component causing Defective NTC Temperature Sensor Probe (Thermistor), open/short circuit in the wiring harness, or faulty connector on the ntc temperature sensor & thermistor. must be inspected or replaced.

How do I test electrical resistance for Bosch code 8 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test NTC Temperature Sensor Probe (Thermistor) across Across sensor pins 1-2 (unplugged harness). Expected nominal reading is 4.8kΩ–12kΩ (at 20°C–25°C). Tolerance: Negative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit..

What safety protocol must be followed before servicing Bosch code 8?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

SEMANTIC KNOWLEDGE GRAPH // BOSCH

Related Bosch Dishwasher Error Codes

Diagnostic Link Mesh14 OEM Cross-References

Cross-referenced diagnostic codes for technicians inspecting similar component subsystems.

E0Electronic Control Board (PCB) & Bus Communications
No defect or communication problems between electronic modules (appliance stops, no function...
Inspect Protocol
E01Electronic Control Board (PCB) & Bus Communications
Internal power module fault / Program ends / Power supply or pump switching faulty
Inspect Protocol
E02Heating Element, Thermostat & Safety Fuse
Operation without heating / Operation without zeolite drying system
Inspect Protocol
E03Heating Element, Thermostat & Safety Fuse
Temperature control / Overheating / Operation without auxiliary drying system / Operation wi...
Inspect Protocol
E04Heating Element, Thermostat & Safety Fuse
Flow exchanger motor triac faulty (appliance stops, no function possible)
Inspect Protocol
E05Drainage System & Drain Pump
Program interruption (drain)
Inspect Protocol
E06Drive Motor, Inverter & Tachometer Sensor
Door Hall sensor error / Stops in current position, appliance is without function
Inspect Protocol
E07Heating Element, Thermostat & Safety Fuse
Heating error, operation without additional drying system (applies only to appliances with z...
Inspect Protocol
E08Drainage System & Drain Pump
Program continues without heating, or heating works but with insufficient water for circulat...
Inspect Protocol
E09Heating Element, Thermostat & Safety Fuse
Heating circuit or electrical water heating circuit interrupted (resistance, cables, safety ...
Inspect Protocol
E10Heating Element, Thermostat & Safety Fuse
Bosch E10: Water/air heating failure in Dishwasher; heating circuit does not reach set tempe...
Inspect Protocol
E11NTC Temperature Sensor & Thermistor
Bosch E11: NTC temperature sensor signal out of range (open or short circuit) in Dishwasher.
Inspect Protocol
E13Water Inlet Valve, Aquastop & Flowmeter
The appliance detects a water temperature > 75 °C and turns off the heater
Inspect Protocol
E14NTC Temperature Sensor & Thermistor
Water Fill Error / Reed Switch Fault
Inspect Protocol
CodesErreur.com

Premium appliance diagnostics & repair database.
Powered by AI to help certified technicians worldwide.

Trusted by professionals in CH & FR

Platform

Search DatabasePRO Diagnostic AIPRODiagnostic ToolsBrands

Workshop Tools

Brands (87)OEM ManualsFind Rating PlateParts Locator

For Technicians

SpecialistsTechnician ForumTech JobsPremium

Corporate

Terms of ServicePrivacy PolicyOfficial Swiss Repair Partner: Electroassistance
OPERATIONAL SAFETY SPECIFICATION

SAFETY DISCLAIMER

The technical information, diagnostic guides, error codes, and AI-generated suggestions provided on this website are intended exclusively for certified and qualified professionals. Appliance repair involves severe electrical hazards, high voltages, and mechanical risks that can result in fatal injury or severe property damage. If you are not a trained technician, do not attempt to repair any appliances. CodesErreur assumes no responsibility or liability for any damage, injury, or consequential losses resulting from the use of the information provided on this platform. You use all information entirely at your own risk.

© 2026 CodesErreur. All rights reserved.

Official Swiss Repair Partner: Electroassistance Terms of Service Privacy Policy