OEM VERIFIED BENCH

OFFICIAL FAULT CODEE07

Bosch // OFFICIAL DIAGNOSTIC BENCH

Bosch E07

Q: What safety protocol must be followed before servicing Bosch code E07?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

DishwasherHeating Element, Thermostat & Safety Fuse

Dishwasher

Other Brands Sharing Code E07:ElectroluxE07 AEGE07 CandyE07 HooverE07 ZanussiE07 Arthur MartinE07 RosieresE07 ArdoE07 BaumaticE07 BompaniE07

Symptom / Description

FAULT

Heating error, operation without additional drying system (applies only to appliances with zeolite drying system)

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

Heating fault; Water in fan housing, zeolite heating circuit interrupted; Fan defective or blocked, module on fan defective

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Check the fan motor for faults or blockages. The error is reset if the fan starts successfully on a subsequent attempt. If multiple start attempts fail, the drying step may be skipped, or the error will be displayed at the end of the program.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Bosch Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLHeating Element, Thermostat & Safety FuseDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

25Ω–28Ω (230V / 2000W) / <0.5Ω (Safety Klixon closed)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Immersion / Air Heating Element & Klixon Thermostat

Test Pins & Connections

PROBE (+)

PROBE (-)

Between element terminals (unwired). Insulation to earth casing: >20MΩ (OL)

Tolerance & Diagnostic CriteriaFormula R = V²/P (±5%). Any earth leakage reading below 2MΩ will trip the domestic 30mA RCD breaker.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Cut electrical mains power. Never measure resistance on energized heating circuits.
!Ensure tub water or heating cavity is completely drained and cool to the touch before dismantling.
!Verify absolute zero voltage using an approved 2-pole voltage detector before touching element terminals.

3. Preliminary Mechanical & Visual Checks

Inspect heating element tube for calcification buildup, bulging, pinholes, or blistering.
Check wiring spade terminals for heat discoloration, burnt insulation, or loose crimps.
On thermal Klixon switches: check for manual red reset buttons and verify spring-loaded snap action.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Bosch E07

FAQ TREE

What does error code E07 mean on a Bosch appliance?

Bosch error code E07 indicates: Heating error, operation without additional drying system (applies only to appliances with zeolite drying system).

What is the root cause of Bosch error code E07?

The primary root cause for Bosch code E07 is: Heating fault; Water in fan housing, zeolite heating circuit interrupted; Fan defective or blocked, module on fan defective.

How do I fix or resolve Bosch error code E07?

To resolve error code E07: Check the fan motor for faults or blockages. The error is reset if the fan starts successfully on a subsequent attempt. If multiple start attempts fail, the drying step may be skipped, or the error will be displayed at the end of the program.

Is it safe to clear Bosch error code E07 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Bosch code E07 persists, the physical component causing Heating fault; Water in fan housing, zeolite heating circuit interrupted; Fan defective or blocked, module on fan defective must be inspected or replaced.

How do I test electrical resistance for Bosch code E07 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Immersion / Air Heating Element & Klixon Thermostat across Between element terminals (unwired). Insulation to earth casing: >20MΩ (OL). Expected nominal reading is 25Ω–28Ω (230V / 2000W) / <0.5Ω (Safety Klixon closed). Tolerance: Formula R = V²/P (±5%). Any earth leakage reading below 2MΩ will trip the domestic 30mA RCD breaker..

What safety protocol must be followed before servicing Bosch code E07?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEE07

Bosch // OFFICIAL DIAGNOSTIC BENCH

Bosch E07

DishwasherHeating Element, Thermostat & Safety Fuse

Dishwasher

Other Brands Sharing Code E07:ElectroluxE07 AEGE07 CandyE07 HooverE07 ZanussiE07 Arthur MartinE07 RosieresE07 ArdoE07 BaumaticE07 BompaniE07

Symptom / Description

FAULT

Heating error, operation without additional drying system (applies only to appliances with zeolite drying system)

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

Heating fault; Water in fan housing, zeolite heating circuit interrupted; Fan defective or blocked, module on fan defective

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Bosch Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLHeating Element, Thermostat & Safety FuseDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

25Ω–28Ω (230V / 2000W) / <0.5Ω (Safety Klixon closed)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Immersion / Air Heating Element & Klixon Thermostat

Test Pins & Connections

PROBE (+)

PROBE (-)

Between element terminals (unwired). Insulation to earth casing: >20MΩ (OL)

Tolerance & Diagnostic CriteriaFormula R = V²/P (±5%). Any earth leakage reading below 2MΩ will trip the domestic 30mA RCD breaker.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Cut electrical mains power. Never measure resistance on energized heating circuits.
!Ensure tub water or heating cavity is completely drained and cool to the touch before dismantling.
!Verify absolute zero voltage using an approved 2-pole voltage detector before touching element terminals.

3. Preliminary Mechanical & Visual Checks

Inspect heating element tube for calcification buildup, bulging, pinholes, or blistering.
Check wiring spade terminals for heat discoloration, burnt insulation, or loose crimps.
On thermal Klixon switches: check for manual red reset buttons and verify spring-loaded snap action.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Bosch E07

FAQ TREE

What does error code E07 mean on a Bosch appliance?

Bosch error code E07 indicates: Heating error, operation without additional drying system (applies only to appliances with zeolite drying system).

What is the root cause of Bosch error code E07?

The primary root cause for Bosch code E07 is: Heating fault; Water in fan housing, zeolite heating circuit interrupted; Fan defective or blocked, module on fan defective.

How do I fix or resolve Bosch error code E07?

Is it safe to clear Bosch error code E07 by resetting power?

How do I test electrical resistance for Bosch code E07 using a multimeter?

What safety protocol must be followed before servicing Bosch code E07?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Bosch E07

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Bosch E07

Community Verification

Related Bosch Dishwasher Error Codes

Bosch E07

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Bosch E07

Community Verification

Related Bosch Dishwasher Error Codes