Skip to content
CodesErreur.comSWISS PRO ENGINE
Core Diagnostics
DiagnosticsBrandsOEM ManualsSpecialistsAI EngineerPRO
Workshop Tools
Diagnostic ToolsNEW
Hardware interfaces & test probes
Find Rating Plate
Locate exact E-Nr, PNC & serial codes
Parts Locator
Global OEM spare parts suppliers
Community & Career
Academy & Courses
Masterclasses by senior technicians
Certification ExamsPRO
Verify your B2B technical credentials
Elite Forum
Peer-to-peer field troubleshooting
Tech Jobs
B2B recruitment & field opportunities
Leaderboard
Global ranking of verified specialists
Certified Appliance Engineering EcosystemApply for Certification →
Language Selector
Account & Access
Upgrade PRO
Back to Search
OEM VERIFIED BENCH
OFFICIAL FAULT CODEE312
Bosch
Bosch // OFFICIAL DIAGNOSTIC BENCH

Bosch E312

OvenNTC Temperature Sensor & Thermistor
Integrated luxury convection oven and induction cooktop with illuminated touch controls
Oven

Symptom / Description

FAULT

Bosch E312: NTC temperature sensor signal out of range (open or short circuit) in Oven / Microwave.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

NTC south control module fault

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED
1Disconnect 230V mains power. 2. Unplug NTC thermistor harness connector. 3. Measure NTC resistance with multimeter across pins 1-2 (nominal: 4.8kΩ–12kΩ at 20°C–25°C; resistance should drop smoothly when probe tip is warmed). Replace sensor if open circuit (OL). 4. Reset: Press and hold Start/Reset for 3 to 5 seconds until display shows 0:01. Turn dial to OFF, wait 15 seconds, turn back ON and run rinse cycle.
AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time
AI WORKSHOP PROTOCOL ENGINE
Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH
Need Help? Call a Certified TechnicianWorldwide Bosch Parts Finder
Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLNTC Temperature Sensor & ThermistorOven / Microwave
2. Multimeter & Electrical Bench Tests (Ω)
MODE: OHMMETER (Ω)AUTO-RANGE
Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board
CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)
Nominal Resistance (Ω)
4.8kΩ–12kΩ (at 20°C–25°C)NOMINAL
0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)
▲ NOMINAL OPERATING WINDOW
Target Component:NTC Temperature Sensor Probe (Thermistor)
Test Pins & Connections
PROBE (+)
PROBE (-)
Across sensor pins 1-2 (unplugged harness)
Tolerance & Diagnostic CriteriaNegative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit.
1. Pre-Intervention Electrical Safety Protocols
  • !Electrical Safety Protocol: Disconnect 230V electrical mains power before removing appliance side or rear panels.
  • !Ensure tub water or heating chamber has cooled below 30°C before unclipping thermistor probe.
  • !Use CAT III 600V/1000V insulated test probes when tng at PCB edge connectors.
3. Preliminary Mechanical & Visual Checks
  • Inspect sensor immersion sleeve for calcification, limescale scale, or thermal paste degradation.
  • Check wiring harness for pinch points, chafing against chassis metal, and terminal pin oxidation.
  • Verify probe is firmly seated in its rubber grommet or bracket inside the water/air circuit.
Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Bosch E312

FAQ TREE
What does error code E312 mean on a Bosch appliance?

Bosch error code E312 indicates: Bosch E312: NTC temperature sensor signal out of range (open or short circuit) in Oven / Microwave..

What is the root cause of Bosch error code E312?

The primary root cause for Bosch code E312 is: NTC south control module fault.

How do I fix or resolve Bosch error code E312?

To resolve error code E312: 1. Disconnect 230V mains power. 2. Unplug NTC thermistor harness connector. 3. Measure NTC resistance with multimeter across pins 1-2 (nominal: 4.8kΩ–12kΩ at 20°C–25°C; resistance should drop smoothly when probe tip is warmed). Replace sensor if open circuit (OL). 4. Reset: Press and hold Start/Reset for 3 to 5 seconds until display shows 0:01. Turn dial to OFF, wait 15 seconds, turn back ON and run rinse cycle.

Is it safe to clear Bosch error code E312 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Bosch code E312 persists, the physical component causing NTC south control module fault must be inspected or replaced.

How do I test electrical resistance for Bosch code E312 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test NTC Temperature Sensor Probe (Thermistor) across Across sensor pins 1-2 (unplugged harness). Expected nominal reading is 4.8kΩ–12kΩ (at 20°C–25°C). Tolerance: Negative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit..

What safety protocol must be followed before servicing Bosch code E312?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

SEMANTIC KNOWLEDGE GRAPH // BOSCH

Related Bosch Oven / Microwave Error Codes

Diagnostic Link Mesh14 OEM Cross-References

Cross-referenced diagnostic codes for technicians inspecting similar component subsystems.

E344Electronic Control Board (PCB) & Bus Communications
Bosch E344: Operational cycle fault detected during Oven / Microwave program execution.
Inspect Protocol
E395Electronic Control Board (PCB) & Bus Communications
Bosch E395: Operational cycle fault detected during Oven / Microwave program execution.
Inspect Protocol
E396Electronic Control Board (PCB) & Bus Communications
Electronic control board EEPROM non-volatile memory read communication error.
Inspect Protocol
E397Electronic Control Board (PCB) & Bus Communications
Bosch E397: Operational cycle fault detected during Oven / Microwave program execution.
Inspect Protocol
E398Electronic Control Board (PCB) & Bus Communications
Bosch E398: Operational cycle fault detected during Oven / Microwave program execution.
Inspect Protocol
E399Electronic Control Board (PCB) & Bus Communications
Bosch E399: Operational cycle fault detected during Oven / Microwave program execution.
Inspect Protocol
E516NTC Temperature Sensor & Thermistor
Core temperature probe (meat thermometer) circuit fault detected on the oven.
Inspect Protocol
Er 0Electronic Control Board (PCB) & Bus Communications
Incorrect module combination detected, no further operation possible.
Inspect Protocol
Er 1NTC Temperature Sensor & Thermistor
Temperature sensor interruption detected, oven does not heat, fans turn on.
Inspect Protocol
Er 11General System & Mechanical Integration
Bosch ER 11: Operational cycle fault detected during Oven / Microwave program execution.
Inspect Protocol
Er 15Heating Element, Thermostat & Safety Fuse
Oven is too hot, heating elements switched off, oven locked.
Inspect Protocol
Er 2General System & Mechanical Integration
Incorrect mains connection, continuous buzzer tone, mains connection incorrect
Inspect Protocol
Er 3Heating Element, Thermostat & Safety Fuse
Electronics overheated (> 100 °C), no heating, display darker, cooling fan on
Inspect Protocol
Er 4NTC Temperature Sensor & Thermistor
Temperature sensor short circuit detected, oven does not heat.
Inspect Protocol
CodesErreur.com

Premium appliance diagnostics & repair database.
Powered by AI to help certified technicians worldwide.

Trusted by professionals in CH & FR

Platform

Search DatabasePRO Diagnostic AIPRODiagnostic ToolsBrands

Workshop Tools

Brands (87)OEM ManualsFind Rating PlateParts Locator

For Technicians

SpecialistsTechnician ForumTech JobsPremium

Corporate

Terms of ServicePrivacy PolicyOfficial Swiss Repair Partner: Electroassistance
OPERATIONAL SAFETY SPECIFICATION

SAFETY DISCLAIMER

The technical information, diagnostic guides, error codes, and AI-generated suggestions provided on this website are intended exclusively for certified and qualified professionals. Appliance repair involves severe electrical hazards, high voltages, and mechanical risks that can result in fatal injury or severe property damage. If you are not a trained technician, do not attempt to repair any appliances. CodesErreur assumes no responsibility or liability for any damage, injury, or consequential losses resulting from the use of the information provided on this platform. You use all information entirely at your own risk.

© 2026 CodesErreur. All rights reserved.

Official Swiss Repair Partner: Electroassistance Terms of Service Privacy Policy