OEM VERIFIED BENCH

OFFICIAL FAULT CODEF105

Electrolux // OFFICIAL DIAGNOSTIC BENCH

Electrolux F105

OvenNTC Temperature Sensor & Thermistor

Oven

Other Brands Sharing Code F105:MieleF105 AEGF105 ZanussiF105 Arthur MartinF105 CastorF105 FaureF105 FrigidaireF105 KelvinatorF105 WestinghouseF105 ZoppasF105

Symptom / Description

FAULT

Electrolux CombiSteam / SurroundCook / Intuit Oven: Food meat probe circuit error F105; internal temperature sensing probe jack shorted, open, or reading abnormal resistance.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Electrolux (Electrolux CombiSteam / SurroundCook / Intuit Oven) models: Grease or moisture penetration inside probe cavity jack, damaged silicone cable on meat probe needle, or open PT1000 sensor inside probe tip (~1079 Ω at 20°C).

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Unplug meat probe from cavity socket. Clean socket contacts with isopropyl alcohol. Measure probe resistance across plug pins with multimeter (~1079 Ω at 20°C). Hold Start/Pause and Delay Start together for 5 seconds on program position 10 until the acoustic chime sounds and display resets to 0:00.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Electrolux Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLNTC Temperature Sensor & ThermistorOven / Microwave

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

4.8kΩ–12kΩ (at 20°C–25°C)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:NTC Temperature Sensor Probe (Thermistor)

Test Pins & Connections

PROBE (+)

PROBE (-)

Across sensor pins 1-2 (unplugged harness)

Tolerance & Diagnostic CriteriaNegative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Disconnect 230V electrical mains power before removing appliance side or rear panels.
!Ensure tub water or heating chamber has cooled below 30°C before unclipping thermistor probe.
!Use CAT III 600V/1000V insulated test probes when tng at PCB edge connectors.

3. Preliminary Mechanical & Visual Checks

Inspect sensor immersion sleeve for calcification, limescale scale, or thermal paste degradation.
Check wiring harness for pinch points, chafing against chassis metal, and terminal pin oxidation.
Verify probe is firmly seated in its rubber grommet or bracket inside the water/air circuit.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Electrolux F105

FAQ TREE

What does error code F105 mean on a Electrolux appliance?

Electrolux error code F105 indicates: Electrolux CombiSteam / SurroundCook / Intuit Oven: Food meat probe circuit error F105; internal temperature sensing probe jack shorted, open, or reading abnormal resistance..

What is the root cause of Electrolux error code F105?

The primary root cause for Electrolux code F105 is: On Electrolux (Electrolux CombiSteam / SurroundCook / Intuit Oven) models: Grease or moisture penetration inside probe cavity jack, damaged silicone cable on meat probe needle, or open PT1000 sensor inside probe tip (~1079 Ω at 20°C)..

How do I fix or resolve Electrolux error code F105?

To resolve error code F105: Unplug meat probe from cavity socket. Clean socket contacts with isopropyl alcohol. Measure probe resistance across plug pins with multimeter (~1079 Ω at 20°C). Hold Start/Pause and Delay Start together for 5 seconds on program position 10 until the acoustic chime sounds and display resets to 0:00.

Is it safe to clear Electrolux error code F105 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Electrolux code F105 persists, the physical component causing On Electrolux (Electrolux CombiSteam / SurroundCook / Intuit Oven) models: Grease or moisture penetration inside probe cavity jack, damaged silicone cable on meat probe needle, or open PT1000 sensor inside probe tip (~1079 Ω at 20°C). must be inspected or replaced.

How do I test electrical resistance for Electrolux code F105 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test NTC Temperature Sensor Probe (Thermistor) across Across sensor pins 1-2 (unplugged harness). Expected nominal reading is 4.8kΩ–12kΩ (at 20°C–25°C). Tolerance: Negative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit..

What safety protocol must be followed before servicing Electrolux code F105?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEF105

Electrolux // OFFICIAL DIAGNOSTIC BENCH

Electrolux F105

OvenNTC Temperature Sensor & Thermistor

Oven

Other Brands Sharing Code F105:MieleF105 AEGF105 ZanussiF105 Arthur MartinF105 CastorF105 FaureF105 FrigidaireF105 KelvinatorF105 WestinghouseF105 ZoppasF105

Symptom / Description

FAULT

Electrolux CombiSteam / SurroundCook / Intuit Oven: Food meat probe circuit error F105; internal temperature sensing probe jack shorted, open, or reading abnormal resistance.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Electrolux Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLNTC Temperature Sensor & ThermistorOven / Microwave

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

4.8kΩ–12kΩ (at 20°C–25°C)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:NTC Temperature Sensor Probe (Thermistor)

Test Pins & Connections

PROBE (+)

PROBE (-)

Across sensor pins 1-2 (unplugged harness)

Tolerance & Diagnostic CriteriaNegative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Disconnect 230V electrical mains power before removing appliance side or rear panels.
!Ensure tub water or heating chamber has cooled below 30°C before unclipping thermistor probe.
!Use CAT III 600V/1000V insulated test probes when tng at PCB edge connectors.

3. Preliminary Mechanical & Visual Checks

Inspect sensor immersion sleeve for calcification, limescale scale, or thermal paste degradation.
Check wiring harness for pinch points, chafing against chassis metal, and terminal pin oxidation.
Verify probe is firmly seated in its rubber grommet or bracket inside the water/air circuit.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Electrolux F105

FAQ TREE

What does error code F105 mean on a Electrolux appliance?

What is the root cause of Electrolux error code F105?

How do I fix or resolve Electrolux error code F105?

Is it safe to clear Electrolux error code F105 by resetting power?

How do I test electrical resistance for Electrolux code F105 using a multimeter?

What safety protocol must be followed before servicing Electrolux code F105?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Electrolux F105

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Electrolux F105

Community Verification

Related Electrolux Oven / Microwave Error Codes

Electrolux F105

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Electrolux F105

Community Verification

Related Electrolux Oven / Microwave Error Codes