OEM VERIFIED BENCH

OFFICIAL FAULT CODEE10

Faber // OFFICIAL DIAGNOSTIC BENCH

Faber E10

Hob / CooktopDrive Motor, Inverter & Tachometer Sensor

Integrated luxury convection oven and induction cooktop with illuminated touch controls

Hob / Cooktop

Other Brands Sharing Code E10:BoschE10 SiemensE10 SamsungE10 LGE10 ElectroluxE10 AEGE10 BekoE10 HaierE10 CandyE10 NeffE10

Symptom / Description

FAULT

Faber Galileo (Smart / Comfort / Linear / Gloss / NG) Integrated Extractor Induction Hob: Diagnostic fault code E10 registered by the microcomputer controller. Suction motor overcurrent trip on Galileo extractor.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Faber appliances engineered with Galileo waterproof central collector turbine, dual bridge EGO induction power generators, and touch slider control module: foreign object in central suction intake duct. Metrological tolerance verification: Motor current > 1.8A AC..

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: clear intake duct and inspect blower wheel. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Isolate power supply at the fuse board for 60 seconds. Re-engage power, verify all display digits illuminate '88', then press and hold the Power and Pause keys together for 4 seconds until the buzzer confirms normal standby mode.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Faber Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrive Motor, Inverter & Tachometer SensorHob / Cooktop

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

3Ω–6Ω (BLDC phase U-V-W) / 60Ω–180Ω (Tacho coil) / 1.5Ω–3.5Ω (Universal stator)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:3-Phase Motor Windings / Tacho Generator / Carbon Brushes

Test Pins & Connections

PROBE (+)

PROBE (-)

Across phase pins U-V, V-W, U-W on motor harness; across tacho pins

Tolerance & Diagnostic CriteriaBLDC phase winding values must be strictly balanced within ±0.3Ω. Hand rotation generates 1V–4V AC on tacho.

1. Pre-Intervention Electrical Safety Protocols

!High-Voltage Safety Protocol & DC Bus: Wait at least 5 minutes after power cutoff to allow inverter DC bus capacitors (380V DC) to bleed down.
!Verify 0V DC across inverter filter capacitors before unplugging motor harness connectors.
!Keep hands clear of drive belt and pulleys during any manual rotation tng.

3. Preliminary Mechanical & Visual Checks

Slip off drive belt and spin drum/motor shaft by hand to check for roaring or seized ball bearings.
For universal motors: verify carbon brushes have at least 10mm remaining length and smooth contact faces.
Inspect motor suspension rubber mounts and drive belt tension/groove profile.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Faber E10

FAQ TREE

What does error code E10 mean on a Faber appliance?

Faber error code E10 indicates: Faber Galileo (Smart / Comfort / Linear / Gloss / NG) Integrated Extractor Induction Hob: Diagnostic fault code E10 registered by the microcomputer controller. Suction motor overcurrent trip on Galileo extractor..

What is the root cause of Faber error code E10?

The primary root cause for Faber code E10 is: On Faber appliances engineered with Galileo waterproof central collector turbine, dual bridge EGO induction power generators, and touch slider control module: foreign object in central suction intake duct. Metrological tolerance verification: Motor current > 1.8A AC...

How do I fix or resolve Faber error code E10?

To resolve error code E10: Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: clear intake duct and inspect blower wheel. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Isolate power supply at the fuse board for 60 seconds. Re-engage power, verify all display digits illuminate '88', then press and hold the Power and Pause keys together for 4 seconds until the buzzer confirms normal standby mode.

Is it safe to clear Faber error code E10 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Faber code E10 persists, the physical component causing On Faber appliances engineered with Galileo waterproof central collector turbine, dual bridge EGO induction power generators, and touch slider control module: foreign object in central suction intake duct. Metrological tolerance verification: Motor current > 1.8A AC.. must be inspected or replaced.

How do I test electrical resistance for Faber code E10 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test 3-Phase Motor Windings / Tacho Generator / Carbon Brushes across Across phase pins U-V, V-W, U-W on motor harness; across tacho pins. Expected nominal reading is 3Ω–6Ω (BLDC phase U-V-W) / 60Ω–180Ω (Tacho coil) / 1.5Ω–3.5Ω (Universal stator). Tolerance: BLDC phase winding values must be strictly balanced within ±0.3Ω. Hand rotation generates 1V–4V AC on tacho..

What safety protocol must be followed before servicing Faber code E10?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEE10

Faber // OFFICIAL DIAGNOSTIC BENCH

Faber E10

Hob / CooktopDrive Motor, Inverter & Tachometer Sensor

Hob / Cooktop

Other Brands Sharing Code E10:BoschE10 SiemensE10 SamsungE10 LGE10 ElectroluxE10 AEGE10 BekoE10 HaierE10 CandyE10 NeffE10

Symptom / Description

FAULT

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Faber Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrive Motor, Inverter & Tachometer SensorHob / Cooktop

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

3Ω–6Ω (BLDC phase U-V-W) / 60Ω–180Ω (Tacho coil) / 1.5Ω–3.5Ω (Universal stator)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:3-Phase Motor Windings / Tacho Generator / Carbon Brushes

Test Pins & Connections

PROBE (+)

PROBE (-)

Across phase pins U-V, V-W, U-W on motor harness; across tacho pins

Tolerance & Diagnostic CriteriaBLDC phase winding values must be strictly balanced within ±0.3Ω. Hand rotation generates 1V–4V AC on tacho.

1. Pre-Intervention Electrical Safety Protocols

!High-Voltage Safety Protocol & DC Bus: Wait at least 5 minutes after power cutoff to allow inverter DC bus capacitors (380V DC) to bleed down.
!Verify 0V DC across inverter filter capacitors before unplugging motor harness connectors.
!Keep hands clear of drive belt and pulleys during any manual rotation tng.

3. Preliminary Mechanical & Visual Checks

Slip off drive belt and spin drum/motor shaft by hand to check for roaring or seized ball bearings.
For universal motors: verify carbon brushes have at least 10mm remaining length and smooth contact faces.
Inspect motor suspension rubber mounts and drive belt tension/groove profile.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Faber E10

FAQ TREE

What does error code E10 mean on a Faber appliance?

What is the root cause of Faber error code E10?

How do I fix or resolve Faber error code E10?

Is it safe to clear Faber error code E10 by resetting power?

How do I test electrical resistance for Faber code E10 using a multimeter?

What safety protocol must be followed before servicing Faber code E10?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Faber E10

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Faber E10

Community Verification

Related Faber Hob / Cooktop Error Codes

Faber E10

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Faber E10

Community Verification

Related Faber Hob / Cooktop Error Codes