OEM VERIFIED BENCH

OFFICIAL FAULT CODEd23

FAGOR // OFFICIAL DIAGNOSTIC BENCH

FAGOR d23

Washing MachineNTC Temperature Sensor & Thermistor

Washing Machine

Other Brands Sharing Code d23:BrandtD23 De DietrichD23 SauterD23

Symptom / Description

FAULT

Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Condenser drying NTC thermistor fault d23; temperature sensing on the condensation duct fails verification.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On FAGOR washer-dryers featuring Innova electronic architecture, dual d01-d27 / F01-F15 diagnostic telemetry, and robust motor drive with 15mm carbon brushes: Open or shorted condenser NTC thermistor probe (~20 kΩ at 20°C, ~5 kΩ at 60°C), or moisture ingress in harness plug.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Disconnect sensor plug on condensation duct. Measure resistance (~20 kΩ at 20°C). Replace NTC sensor probe if reading is open or zero ohms. Turn selector dial to 0, press and hold Start/Pause and Extra Rinse buttons for 6 seconds until 'F00' or display resets, then restart.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide FAGOR Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLNTC Temperature Sensor & ThermistorWashing Machine

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

4.8kΩ–12kΩ (at 20°C–25°C)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:NTC Temperature Sensor Probe (Thermistor)

Test Pins & Connections

PROBE (+)

PROBE (-)

Across sensor pins 1-2 (unplugged harness)

Tolerance & Diagnostic CriteriaNegative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Disconnect 230V electrical mains power before removing appliance side or rear panels.
!Ensure tub water or heating chamber has cooled below 30°C before unclipping thermistor probe.
!Use CAT III 600V/1000V insulated test probes when tng at PCB edge connectors.

3. Preliminary Mechanical & Visual Checks

Inspect sensor immersion sleeve for calcification, limescale scale, or thermal paste degradation.
Check wiring harness for pinch points, chafing against chassis metal, and terminal pin oxidation.
Verify probe is firmly seated in its rubber grommet or bracket inside the water/air circuit.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: FAGOR D23

FAQ TREE

What does error code D23 mean on a FAGOR appliance?

FAGOR error code D23 indicates: Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Condenser drying NTC thermistor fault d23; temperature sensing on the condensation duct fails verification..

What is the root cause of FAGOR error code D23?

The primary root cause for FAGOR code D23 is: On FAGOR washer-dryers featuring Innova electronic architecture, dual d01-d27 / F01-F15 diagnostic telemetry, and robust motor drive with 15mm carbon brushes: Open or shorted condenser NTC thermistor probe (~20 kΩ at 20°C, ~5 kΩ at 60°C), or moisture ingress in harness plug..

How do I fix or resolve FAGOR error code D23?

To resolve error code D23: Disconnect sensor plug on condensation duct. Measure resistance (~20 kΩ at 20°C). Replace NTC sensor probe if reading is open or zero ohms. Turn selector dial to 0, press and hold Start/Pause and Extra Rinse buttons for 6 seconds until 'F00' or display resets, then restart.

Is it safe to clear FAGOR error code D23 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if FAGOR code D23 persists, the physical component causing On FAGOR washer-dryers featuring Innova electronic architecture, dual d01-d27 / F01-F15 diagnostic telemetry, and robust motor drive with 15mm carbon brushes: Open or shorted condenser NTC thermistor probe (~20 kΩ at 20°C, ~5 kΩ at 60°C), or moisture ingress in harness plug. must be inspected or replaced.

How do I test electrical resistance for FAGOR code D23 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test NTC Temperature Sensor Probe (Thermistor) across Across sensor pins 1-2 (unplugged harness). Expected nominal reading is 4.8kΩ–12kΩ (at 20°C–25°C). Tolerance: Negative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit..

What safety protocol must be followed before servicing FAGOR code D23?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEd23

FAGOR // OFFICIAL DIAGNOSTIC BENCH

FAGOR d23

Washing MachineNTC Temperature Sensor & Thermistor

Washing Machine

Other Brands Sharing Code d23:BrandtD23 De DietrichD23 SauterD23

Symptom / Description

FAULT

Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Condenser drying NTC thermistor fault d23; temperature sensing on the condensation duct fails verification.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide FAGOR Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLNTC Temperature Sensor & ThermistorWashing Machine

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

4.8kΩ–12kΩ (at 20°C–25°C)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:NTC Temperature Sensor Probe (Thermistor)

Test Pins & Connections

PROBE (+)

PROBE (-)

Across sensor pins 1-2 (unplugged harness)

Tolerance & Diagnostic CriteriaNegative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Disconnect 230V electrical mains power before removing appliance side or rear panels.
!Ensure tub water or heating chamber has cooled below 30°C before unclipping thermistor probe.
!Use CAT III 600V/1000V insulated test probes when tng at PCB edge connectors.

3. Preliminary Mechanical & Visual Checks

Inspect sensor immersion sleeve for calcification, limescale scale, or thermal paste degradation.
Check wiring harness for pinch points, chafing against chassis metal, and terminal pin oxidation.
Verify probe is firmly seated in its rubber grommet or bracket inside the water/air circuit.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: FAGOR D23

FAQ TREE

What does error code D23 mean on a FAGOR appliance?

What is the root cause of FAGOR error code D23?

How do I fix or resolve FAGOR error code D23?

Is it safe to clear FAGOR error code D23 by resetting power?

How do I test electrical resistance for FAGOR code D23 using a multimeter?

What safety protocol must be followed before servicing FAGOR code D23?

Community Verification

COMMUNITY

Did this solution resolve the issue?

FAGOR d23

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: FAGOR D23

Community Verification

Related FAGOR Washing Machine Error Codes

FAGOR d23

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: FAGOR D23

Community Verification

Related FAGOR Washing Machine Error Codes