OEM VERIFIED BENCH

OFFICIAL FAULT CODEE73

Faure // OFFICIAL DIAGNOSTIC BENCH

Faure E73

Washing MachineNTC Temperature Sensor & Thermistor

Washing Machine

Select Appliance Type

0ms Instant Telemetry Switch

Other Brands Sharing Code E73:ElectroluxE73 AEGE73 ZanussiE73 Arthur MartinE73 CastorE73 FrigidaireE73 WestinghouseE73 ZoppasE73

Symptom / Description

FAULT

Faure FWG / FWF Series / Magic'45 Compact Washer: Drying air duct NTC sensor fault E73 on washer-dryer; hot air process temperature signal out of range.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Faure (Faure FWG / FWF Series / Magic'45 Compact Washer) models: Drying air duct NTC sensor open or shorted, thick lint blanket insulating sensor tip, or overheated wiring harness near drying heater box.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Dismantle upper drying heater duct. Clean lint from sensor tip. Measure NTC resistance (4.8–6.0 kΩ at 20°C). Replace if out of range. Press and hold Départ/Pause and Annulation buttons for 6 seconds until all status indicators flash synchronously and clear fault memory.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Faure Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLNTC Temperature Sensor & ThermistorWashing Machine

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

4.8kΩ–12kΩ (at 20°C–25°C)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:NTC Temperature Sensor Probe (Thermistor)

Test Pins & Connections

PROBE (+)

PROBE (-)

Across sensor pins 1-2 (unplugged harness)

Tolerance & Diagnostic CriteriaNegative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Disconnect 230V electrical mains power before removing appliance side or rear panels.
!Ensure tub water or heating chamber has cooled below 30°C before unclipping thermistor probe.
!Use CAT III 600V/1000V insulated test probes when tng at PCB edge connectors.

3. Preliminary Mechanical & Visual Checks

Inspect sensor immersion sleeve for calcification, limescale scale, or thermal paste degradation.
Check wiring harness for pinch points, chafing against chassis metal, and terminal pin oxidation.
Verify probe is firmly seated in its rubber grommet or bracket inside the water/air circuit.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Faure E73

FAQ TREE

What does error code E73 mean on a Faure appliance?

Faure error code E73 indicates: Faure FWG / FWF Series / Magic'45 Compact Washer: Drying air duct NTC sensor fault E73 on washer-dryer; hot air process temperature signal out of range..

What is the root cause of Faure error code E73?

The primary root cause for Faure code E73 is: On Faure (Faure FWG / FWF Series / Magic'45 Compact Washer) models: Drying air duct NTC sensor open or shorted, thick lint blanket insulating sensor tip, or overheated wiring harness near drying heater box..

How do I fix or resolve Faure error code E73?

To resolve error code E73: Dismantle upper drying heater duct. Clean lint from sensor tip. Measure NTC resistance (4.8–6.0 kΩ at 20°C). Replace if out of range. Press and hold Départ/Pause and Annulation buttons for 6 seconds until all status indicators flash synchronously and clear fault memory.

Is it safe to clear Faure error code E73 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Faure code E73 persists, the physical component causing On Faure (Faure FWG / FWF Series / Magic'45 Compact Washer) models: Drying air duct NTC sensor open or shorted, thick lint blanket insulating sensor tip, or overheated wiring harness near drying heater box. must be inspected or replaced.

How do I test electrical resistance for Faure code E73 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test NTC Temperature Sensor Probe (Thermistor) across Across sensor pins 1-2 (unplugged harness). Expected nominal reading is 4.8kΩ–12kΩ (at 20°C–25°C). Tolerance: Negative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit..

What safety protocol must be followed before servicing Faure code E73?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEE73

Faure // OFFICIAL DIAGNOSTIC BENCH

Faure E73

Washing MachineNTC Temperature Sensor & Thermistor

Washing Machine

Select Appliance Type

0ms Instant Telemetry Switch

Other Brands Sharing Code E73:ElectroluxE73 AEGE73 ZanussiE73 Arthur MartinE73 CastorE73 FrigidaireE73 WestinghouseE73 ZoppasE73

Symptom / Description

FAULT

Faure FWG / FWF Series / Magic'45 Compact Washer: Drying air duct NTC sensor fault E73 on washer-dryer; hot air process temperature signal out of range.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Faure Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLNTC Temperature Sensor & ThermistorWashing Machine

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

4.8kΩ–12kΩ (at 20°C–25°C)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:NTC Temperature Sensor Probe (Thermistor)

Test Pins & Connections

PROBE (+)

PROBE (-)

Across sensor pins 1-2 (unplugged harness)

Tolerance & Diagnostic CriteriaNegative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Disconnect 230V electrical mains power before removing appliance side or rear panels.
!Ensure tub water or heating chamber has cooled below 30°C before unclipping thermistor probe.
!Use CAT III 600V/1000V insulated test probes when tng at PCB edge connectors.

3. Preliminary Mechanical & Visual Checks

Inspect sensor immersion sleeve for calcification, limescale scale, or thermal paste degradation.
Check wiring harness for pinch points, chafing against chassis metal, and terminal pin oxidation.
Verify probe is firmly seated in its rubber grommet or bracket inside the water/air circuit.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Faure E73

FAQ TREE

What does error code E73 mean on a Faure appliance?

Faure error code E73 indicates: Faure FWG / FWF Series / Magic'45 Compact Washer: Drying air duct NTC sensor fault E73 on washer-dryer; hot air process temperature signal out of range..

What is the root cause of Faure error code E73?

How do I fix or resolve Faure error code E73?

Is it safe to clear Faure error code E73 by resetting power?

How do I test electrical resistance for Faure code E73 using a multimeter?

What safety protocol must be followed before servicing Faure code E73?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Faure E73

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Faure E73

Community Verification

Related Faure Washing Machine Error Codes

Faure E73

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Faure E73

Community Verification

Related Faure Washing Machine Error Codes