OEM VERIFIED BENCH

OFFICIAL FAULT CODEi30

Frigidaire // OFFICIAL DIAGNOSTIC BENCH

Frigidaire i30

DishwasherDrainage System & Drain Pump

Dishwasher

Other Brands Sharing Code i30:ElectroluxI30 AEGI30 V-ZugI30 ZanussiI30 Arthur MartinI30 SchulthessI30 FAGORI30 Schaub LorenzI30 AirluxI30 AtlanticI30

Symptom / Description

FAULT

Frigidaire Gallery / OrbitClean Wash Dishwasher: AquaControl flood protection active i30; base drip tray float triggered, drain pump runs continuously.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Frigidaire (Frigidaire Gallery / OrbitClean Wash Dishwasher) models: Internal water leak onto bottom pan, leaking door lower perimeter gasket, split circulation pump casing, or overflowing dispenser.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Disconnect power and shut water tap. Sponge out water from metal base pan. Inspect sump gasket, hoses, and door bottom seal for moisture. Press and hold Cancel / Drain for 3 seconds, or cycle the control lock for 5 seconds to clear persistent memory fault log.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Frigidaire Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Frigidaire I30

FAQ TREE

What does error code I30 mean on a Frigidaire appliance?

Frigidaire error code I30 indicates: Frigidaire Gallery / OrbitClean Wash Dishwasher: AquaControl flood protection active i30; base drip tray float triggered, drain pump runs continuously..

What is the root cause of Frigidaire error code I30?

The primary root cause for Frigidaire code I30 is: On Frigidaire (Frigidaire Gallery / OrbitClean Wash Dishwasher) models: Internal water leak onto bottom pan, leaking door lower perimeter gasket, split circulation pump casing, or overflowing dispenser..

How do I fix or resolve Frigidaire error code I30?

To resolve error code I30: Disconnect power and shut water tap. Sponge out water from metal base pan. Inspect sump gasket, hoses, and door bottom seal for moisture. Press and hold Cancel / Drain for 3 seconds, or cycle the control lock for 5 seconds to clear persistent memory fault log.

Is it safe to clear Frigidaire error code I30 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Frigidaire code I30 persists, the physical component causing On Frigidaire (Frigidaire Gallery / OrbitClean Wash Dishwasher) models: Internal water leak onto bottom pan, leaking door lower perimeter gasket, split circulation pump casing, or overflowing dispenser. must be inspected or replaced.

How do I test electrical resistance for Frigidaire code I30 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Drain Pump Motor Stator Coils across Across pump motor spade terminals (L-N unclipped). Expected nominal reading is 160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC). Tolerance: ±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ..

What safety protocol must be followed before servicing Frigidaire code I30?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEi30

Frigidaire // OFFICIAL DIAGNOSTIC BENCH

Frigidaire i30

DishwasherDrainage System & Drain Pump

Dishwasher

Other Brands Sharing Code i30:ElectroluxI30 AEGI30 V-ZugI30 ZanussiI30 Arthur MartinI30 SchulthessI30 FAGORI30 Schaub LorenzI30 AirluxI30 AtlanticI30

Symptom / Description

FAULT

Frigidaire Gallery / OrbitClean Wash Dishwasher: AquaControl flood protection active i30; base drip tray float triggered, drain pump runs continuously.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Frigidaire Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Frigidaire I30

FAQ TREE

What does error code I30 mean on a Frigidaire appliance?

Frigidaire error code I30 indicates: Frigidaire Gallery / OrbitClean Wash Dishwasher: AquaControl flood protection active i30; base drip tray float triggered, drain pump runs continuously..

What is the root cause of Frigidaire error code I30?

How do I fix or resolve Frigidaire error code I30?

Is it safe to clear Frigidaire error code I30 by resetting power?

How do I test electrical resistance for Frigidaire code I30 using a multimeter?

What safety protocol must be followed before servicing Frigidaire code I30?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Frigidaire i30

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Frigidaire I30

Community Verification

Related Frigidaire Dishwasher Error Codes

Frigidaire i30

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Frigidaire I30

Community Verification

Related Frigidaire Dishwasher Error Codes