OEM VERIFIED BENCH

OFFICIAL FAULT CODEi30

V-Zug // OFFICIAL DIAGNOSTIC BENCH

V-Zug i30

DishwasherWater Inlet Valve, Aquastop & Flowmeter

Dishwasher

Other Brands Sharing Code i30:ElectroluxI30 AEGI30 ZanussiI30 Arthur MartinI30 SchulthessI30 FAGORI30 Schaub LorenzI30 AirluxI30 AtlanticI30 CastorI30

Symptom / Description

FAULT

Anti-flood system activated

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

Water has leaked into the base of the dishwasher, tripping the safety float switch.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Turn off the water and power to the appliance. The leak source must be identified and repaired by a qualified technician before resetting the system.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide V-Zug Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLWater Inlet Valve, Aquastop & FlowmeterDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

3.5kΩ–4.5kΩ (Standard 230V) / 2.0kΩ–4.2kΩ (Aquastop)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Solenoid Valve Coil / Aquastop Pneumatic Valve

Test Pins & Connections

PROBE (+)

PROBE (-)

Across coil spade terminals (disconnect harness first)

Tolerance & Diagnostic Criteria±10%. Open circuit (OL) indicates burned solenoid coil. Flowmeter turbine reed switch pulses on flow.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Disconnect electrical power before touching solenoid valve coils or Aquastop connectors.
!Firmly shut off the domc water supply tap before unscrewing the inlet hose fitting.
!Check safety base drip tray for accumulated water triggering the anti-flood polystyrene float switch.

3. Preliminary Mechanical & Visual Checks

Remove and clean sediment and sand particles from the 3/4" inlet hose metal mesh filter.
Verify domestic dynamic water pressure is between 1.0 and 10.0 bar (0.1 to 1.0 MPa).
Inspect outer Aquastop hose jacket for expansion, pinch damage, or internal leak reservoir triggering.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: V-Zug I30

FAQ TREE

What does error code I30 mean on a V-Zug appliance?

V-Zug error code I30 indicates: Anti-flood system activated.

What is the root cause of V-Zug error code I30?

The primary root cause for V-Zug code I30 is: Water has leaked into the base of the dishwasher, tripping the safety float switch..

How do I fix or resolve V-Zug error code I30?

To resolve error code I30: Turn off the water and power to the appliance. The leak source must be identified and repaired by a qualified technician before resetting the system.

Is it safe to clear V-Zug error code I30 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if V-Zug code I30 persists, the physical component causing Water has leaked into the base of the dishwasher, tripping the safety float switch. must be inspected or replaced.

How do I test electrical resistance for V-Zug code I30 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Solenoid Valve Coil / Aquastop Pneumatic Valve across Across coil spade terminals (disconnect harness first). Expected nominal reading is 3.5kΩ–4.5kΩ (Standard 230V) / 2.0kΩ–4.2kΩ (Aquastop). Tolerance: ±10%. Open circuit (OL) indicates burned solenoid coil. Flowmeter turbine reed switch pulses on flow..

What safety protocol must be followed before servicing V-Zug code I30?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEi30

V-Zug // OFFICIAL DIAGNOSTIC BENCH

V-Zug i30

DishwasherWater Inlet Valve, Aquastop & Flowmeter

Dishwasher

Other Brands Sharing Code i30:ElectroluxI30 AEGI30 ZanussiI30 Arthur MartinI30 SchulthessI30 FAGORI30 Schaub LorenzI30 AirluxI30 AtlanticI30 CastorI30

Symptom / Description

FAULT

Anti-flood system activated

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

Water has leaked into the base of the dishwasher, tripping the safety float switch.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Turn off the water and power to the appliance. The leak source must be identified and repaired by a qualified technician before resetting the system.

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide V-Zug Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLWater Inlet Valve, Aquastop & FlowmeterDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

3.5kΩ–4.5kΩ (Standard 230V) / 2.0kΩ–4.2kΩ (Aquastop)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Solenoid Valve Coil / Aquastop Pneumatic Valve

Test Pins & Connections

PROBE (+)

PROBE (-)

Across coil spade terminals (disconnect harness first)

Tolerance & Diagnostic Criteria±10%. Open circuit (OL) indicates burned solenoid coil. Flowmeter turbine reed switch pulses on flow.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Disconnect electrical power before touching solenoid valve coils or Aquastop connectors.
!Firmly shut off the domc water supply tap before unscrewing the inlet hose fitting.
!Check safety base drip tray for accumulated water triggering the anti-flood polystyrene float switch.

3. Preliminary Mechanical & Visual Checks

Remove and clean sediment and sand particles from the 3/4" inlet hose metal mesh filter.
Verify domestic dynamic water pressure is between 1.0 and 10.0 bar (0.1 to 1.0 MPa).
Inspect outer Aquastop hose jacket for expansion, pinch damage, or internal leak reservoir triggering.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: V-Zug I30

FAQ TREE

What does error code I30 mean on a V-Zug appliance?

V-Zug error code I30 indicates: Anti-flood system activated.

What is the root cause of V-Zug error code I30?

The primary root cause for V-Zug code I30 is: Water has leaked into the base of the dishwasher, tripping the safety float switch..

How do I fix or resolve V-Zug error code I30?

To resolve error code I30: Turn off the water and power to the appliance. The leak source must be identified and repaired by a qualified technician before resetting the system.

Is it safe to clear V-Zug error code I30 by resetting power?

How do I test electrical resistance for V-Zug code I30 using a multimeter?

What safety protocol must be followed before servicing V-Zug code I30?

Community Verification

COMMUNITY

Did this solution resolve the issue?

V-Zug i30

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: V-Zug I30

Community Verification

Related V-Zug Dishwasher Error Codes

V-Zug i30

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: V-Zug I30

Community Verification

Related V-Zug Dishwasher Error Codes