OEM VERIFIED BENCH

OFFICIAL FAULT CODEAL03

Haier // OFFICIAL DIAGNOSTIC BENCH

Haier AL03

DishwasherDrainage System & Drain Pump

Dishwasher

Other Brands Sharing Code AL03:WhirlpoolAL03 IndesitAL03 CandyAL03 BauknechtAL03 AristonAL03 HooverAL03 ZanussiAL03 De DietrichAL03 GaggenauAL03 SchulthessAL03

Symptom / Description

FAULT

Haier I-Pro Shine / Washlogix Ultra Silence Dishwasher: Drain evacuation alarm AL03; sump fails to empty completely during intermediate rinse drain phase.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Haier dishwashers powered by I-Pro Shine Ultra Silence brushless wash circulation pump, dual-zone inverter spray system, and micro-filtration: Heavy grease clogs in drain hose, sink siphon nipple blocked, or drain pump motor winding weakened (~160–220 Ω).

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Disconnect drain hose from under-sink siphon and verify clear bore. Flush drain hose with warm water. Measure pump motor resistance (~160–220 Ω). Press Power button off, hold Half Load and Start buttons together while powering on until diagnostic test mode 01 displays, then power off.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Haier Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Haier AL03

FAQ TREE

What does error code AL03 mean on a Haier appliance?

Haier error code AL03 indicates: Haier I-Pro Shine / Washlogix Ultra Silence Dishwasher: Drain evacuation alarm AL03; sump fails to empty completely during intermediate rinse drain phase..

What is the root cause of Haier error code AL03?

The primary root cause for Haier code AL03 is: On Haier dishwashers powered by I-Pro Shine Ultra Silence brushless wash circulation pump, dual-zone inverter spray system, and micro-filtration: Heavy grease clogs in drain hose, sink siphon nipple blocked, or drain pump motor winding weakened (~160–220 Ω)..

How do I fix or resolve Haier error code AL03?

To resolve error code AL03: Disconnect drain hose from under-sink siphon and verify clear bore. Flush drain hose with warm water. Measure pump motor resistance (~160–220 Ω). Press Power button off, hold Half Load and Start buttons together while powering on until diagnostic test mode 01 displays, then power off.

Is it safe to clear Haier error code AL03 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Haier code AL03 persists, the physical component causing On Haier dishwashers powered by I-Pro Shine Ultra Silence brushless wash circulation pump, dual-zone inverter spray system, and micro-filtration: Heavy grease clogs in drain hose, sink siphon nipple blocked, or drain pump motor winding weakened (~160–220 Ω). must be inspected or replaced.

How do I test electrical resistance for Haier code AL03 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Drain Pump Motor Stator Coils across Across pump motor spade terminals (L-N unclipped). Expected nominal reading is 160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC). Tolerance: ±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ..

What safety protocol must be followed before servicing Haier code AL03?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEAL03

Haier // OFFICIAL DIAGNOSTIC BENCH

Haier AL03

DishwasherDrainage System & Drain Pump

Dishwasher

Other Brands Sharing Code AL03:WhirlpoolAL03 IndesitAL03 CandyAL03 BauknechtAL03 AristonAL03 HooverAL03 ZanussiAL03 De DietrichAL03 GaggenauAL03 SchulthessAL03

Symptom / Description

FAULT

Haier I-Pro Shine / Washlogix Ultra Silence Dishwasher: Drain evacuation alarm AL03; sump fails to empty completely during intermediate rinse drain phase.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Haier Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Haier AL03

FAQ TREE

What does error code AL03 mean on a Haier appliance?

Haier error code AL03 indicates: Haier I-Pro Shine / Washlogix Ultra Silence Dishwasher: Drain evacuation alarm AL03; sump fails to empty completely during intermediate rinse drain phase..

What is the root cause of Haier error code AL03?

How do I fix or resolve Haier error code AL03?

Is it safe to clear Haier error code AL03 by resetting power?

How do I test electrical resistance for Haier code AL03 using a multimeter?

What safety protocol must be followed before servicing Haier code AL03?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Haier AL03

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Haier AL03

Community Verification

Related Haier Dishwasher Error Codes

Haier AL03

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Haier AL03

Community Verification

Related Haier Dishwasher Error Codes