OEM VERIFIED BENCH

OFFICIAL FAULT CODEE10

Ilve // OFFICIAL DIAGNOSTIC BENCH

Ilve E10

Q: What does error code E10 mean on a ILVE appliance?

ILVE error code E10 indicates: ILVE Professional Series IVFID / IVDIT Fully Integrated Dishwasher: Diagnostic fault code E10 registered by the microcomputer controller. BLDC circulation wash pump motor tachometer or inverter fault.

DishwasherDrainage System & Drain Pump

Dishwasher

Select Appliance Type

0ms Instant Telemetry Switch

Other Brands Sharing Code E10:BoschE10 SiemensE10 SamsungE10 LGE10 ElectroluxE10 AEGE10 BekoE10 HaierE10 CandyE10 NeffE10

Symptom / Description

FAULT

ILVE Professional Series IVFID / IVDIT Fully Integrated Dishwasher: Diagnostic fault code E10 registered by the microcomputer controller. BLDC circulation wash pump motor tachometer or inverter fault

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On ILVE appliances engineered with Professional hydraulic architecture with stainless steel spray arms, brushless BLDC circulation pump, dual electronic water softener valves, and active dry turbine: wash circulation pump motor winding open or impeller locked Metrological tolerance verification: 3-phase pump windings balanced 38 Ω ± 2 Ω..

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: measure resistance across all 3 wash pump motor terminals (expected ~38 Ω). Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Hold the Start/Reset button down for 4 seconds until the machine beeps twice and the display reads '00'. Close the door to allow a 30-second drain cycle to finish before selecting a new wash program.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Ilve Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Ilve E10

FAQ TREE

What does error code E10 mean on a Ilve appliance?

Ilve error code E10 indicates: ILVE Professional Series IVFID / IVDIT Fully Integrated Dishwasher: Diagnostic fault code E10 registered by the microcomputer controller. BLDC circulation wash pump motor tachometer or inverter fault.

What is the root cause of Ilve error code E10?

The primary root cause for Ilve code E10 is: On ILVE appliances engineered with Professional hydraulic architecture with stainless steel spray arms, brushless BLDC circulation pump, dual electronic water softener valves, and active dry turbine: wash circulation pump motor winding open or impeller locked Metrological tolerance verification: 3-phase pump windings balanced 38 Ω ± 2 Ω...

How do I fix or resolve Ilve error code E10?

To resolve error code E10: Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: measure resistance across all 3 wash pump motor terminals (expected ~38 Ω). Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Hold the Start/Reset button down for 4 seconds until the machine beeps twice and the display reads '00'. Close the door to allow a 30-second drain cycle to finish before selecting a new wash program.

Is it safe to clear Ilve error code E10 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Ilve code E10 persists, the physical component causing On ILVE appliances engineered with Professional hydraulic architecture with stainless steel spray arms, brushless BLDC circulation pump, dual electronic water softener valves, and active dry turbine: wash circulation pump motor winding open or impeller locked Metrological tolerance verification: 3-phase pump windings balanced 38 Ω ± 2 Ω.. must be inspected or replaced.

How do I test electrical resistance for Ilve code E10 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Drain Pump Motor Stator Coils across Across pump motor spade terminals (L-N unclipped). Expected nominal reading is 160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC). Tolerance: ±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ..

What safety protocol must be followed before servicing Ilve code E10?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEE10

Ilve // OFFICIAL DIAGNOSTIC BENCH

Ilve E10

DishwasherDrainage System & Drain Pump

Dishwasher

Select Appliance Type

0ms Instant Telemetry Switch

Other Brands Sharing Code E10:BoschE10 SiemensE10 SamsungE10 LGE10 ElectroluxE10 AEGE10 BekoE10 HaierE10 CandyE10 NeffE10

Symptom / Description

FAULT

ILVE Professional Series IVFID / IVDIT Fully Integrated Dishwasher: Diagnostic fault code E10 registered by the microcomputer controller. BLDC circulation wash pump motor tachometer or inverter fault

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Ilve Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Ilve E10

FAQ TREE

What does error code E10 mean on a Ilve appliance?

What is the root cause of Ilve error code E10?

How do I fix or resolve Ilve error code E10?

Is it safe to clear Ilve error code E10 by resetting power?

How do I test electrical resistance for Ilve code E10 using a multimeter?

What safety protocol must be followed before servicing Ilve code E10?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Ilve E10

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Ilve E10

Community Verification

Related ILVE Dishwasher Error Codes

Ilve E10

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Ilve E10

Community Verification

Related ILVE Dishwasher Error Codes