OEM VERIFIED BENCH

OFFICIAL FAULT CODEE04

Rosieres // OFFICIAL DIAGNOSTIC BENCH

Rosieres E04

Q: What does error code E04 mean on a Rosières appliance?

Rosières error code E04 indicates: Rosières RLI / RDS Grande Capacité Built-in Dishwasher: Bottom tray anti-flood switch activated E04; water detected in base pan, triggering continuous drain and lock-out..

Q: What is the root cause of Rosières error code E04?

The primary root cause for Rosières code E04 is: On Rosières dishwashers utilizing Grande Capacité built-in hydraulic circuit, triple-arm spray system, and acoustic soundproofing: Sump O-ring seal leak, perforated tub stainless steel seam, dripping wash pump shaft seal, or leaking water jacket hose..

DishwasherDrainage System & Drain Pump

Dishwasher

Select Appliance Type

0ms Instant Telemetry Switch

Other Brands Sharing Code E04:BoschE04 SiemensE04 SamsungE04 LGE04 ElectroluxE04 AEGE04 BekoE04 HaierE04 CandyE04 NeffE04

Symptom / Description

FAULT

Rosières RLI / RDS Grande Capacité Built-in Dishwasher: Bottom tray anti-flood switch activated E04; water detected in base pan, triggering continuous drain and lock-out.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Rosières dishwashers utilizing Grande Capacité built-in hydraulic circuit, triple-arm spray system, and acoustic soundproofing: Sump O-ring seal leak, perforated tub stainless steel seam, dripping wash pump shaft seal, or leaking water jacket hose.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Isolate electrical supply. Remove side panels and dry bottom pan. Run test cycle while inspecting sump joint, pump mechanical seal, and hose clamps with a torch. Press and hold Start/Cancel button for 6 seconds until all cycle lights extinguish, then switch off mains toggle switch.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Rosieres Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Rosieres E04

FAQ TREE

What does error code E04 mean on a Rosieres appliance?

Rosieres error code E04 indicates: Rosières RLI / RDS Grande Capacité Built-in Dishwasher: Bottom tray anti-flood switch activated E04; water detected in base pan, triggering continuous drain and lock-out..

What is the root cause of Rosieres error code E04?

The primary root cause for Rosieres code E04 is: On Rosières dishwashers utilizing Grande Capacité built-in hydraulic circuit, triple-arm spray system, and acoustic soundproofing: Sump O-ring seal leak, perforated tub stainless steel seam, dripping wash pump shaft seal, or leaking water jacket hose..

How do I fix or resolve Rosieres error code E04?

To resolve error code E04: Isolate electrical supply. Remove side panels and dry bottom pan. Run test cycle while inspecting sump joint, pump mechanical seal, and hose clamps with a torch. Press and hold Start/Cancel button for 6 seconds until all cycle lights extinguish, then switch off mains toggle switch.

Is it safe to clear Rosieres error code E04 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Rosieres code E04 persists, the physical component causing On Rosières dishwashers utilizing Grande Capacité built-in hydraulic circuit, triple-arm spray system, and acoustic soundproofing: Sump O-ring seal leak, perforated tub stainless steel seam, dripping wash pump shaft seal, or leaking water jacket hose. must be inspected or replaced.

How do I test electrical resistance for Rosieres code E04 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Drain Pump Motor Stator Coils across Across pump motor spade terminals (L-N unclipped). Expected nominal reading is 160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC). Tolerance: ±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ..

What safety protocol must be followed before servicing Rosieres code E04?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEE04

Rosieres // OFFICIAL DIAGNOSTIC BENCH

Rosieres E04

DishwasherDrainage System & Drain Pump

Dishwasher

Select Appliance Type

0ms Instant Telemetry Switch

Other Brands Sharing Code E04:BoschE04 SiemensE04 SamsungE04 LGE04 ElectroluxE04 AEGE04 BekoE04 HaierE04 CandyE04 NeffE04

Symptom / Description

FAULT

Rosières RLI / RDS Grande Capacité Built-in Dishwasher: Bottom tray anti-flood switch activated E04; water detected in base pan, triggering continuous drain and lock-out.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Rosieres Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Rosieres E04

FAQ TREE

What does error code E04 mean on a Rosieres appliance?

What is the root cause of Rosieres error code E04?

How do I fix or resolve Rosieres error code E04?

Is it safe to clear Rosieres error code E04 by resetting power?

How do I test electrical resistance for Rosieres code E04 using a multimeter?

What safety protocol must be followed before servicing Rosieres code E04?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Rosieres E04

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Rosieres E04

Community Verification

Related Rosières Dishwasher Error Codes

Rosieres E04

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Rosieres E04

Community Verification

Related Rosières Dishwasher Error Codes